Feed the cord through the holes in the housing and pulley, and tie a knot in the end. Keep tension on the cord with one hand while you release the pliers with the other. Let the pulley slowly rewind.
This starter mechanism comprises a rope, with a grip at the end, moulded rope reels and a spring. The rope is coiled within a reel which is held under spring tension within an outer reel.
What to do after replacing a recoil spring on Husqvarna chainsaw?
How to operate a chainsaw?
How to replace drive disc spring?
Where to put recoil spring on starter?
How to remove slack from a starter?
See 2 more
About this website
How do you rewind a Husqvarna recoil spring?
1:344:15Husqvarna String Trimmer Recoil Spring Replacement #545008087YouTubeStart of suggested clipEnd of suggested clipHold the rewind pulley in place and use pliers to carefully detach the drive spring. Now gentlyMoreHold the rewind pulley in place and use pliers to carefully detach the drive spring. Now gently remove the rewind pulley and the old recoil spring if still intact the spring can cause injury.
How do you rewind a chainsaw pull cord?
0:031:58Chainsaw Recoil Starter Cord Replacement (Correct way to wind ...YouTubeStart of suggested clipEnd of suggested clipThen simply begin by winding the rope back onto the pulley. Either one way or the other. And thenMoreThen simply begin by winding the rope back onto the pulley. Either one way or the other. And then simply place the pulley loose into position inside the housing. No need to fix anything in place.
How do you rewind a pull start?
0:121:46Recoil Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can hold the short piece of rope wind it up we're going to wind it two times and see what thatMoreYou can hold the short piece of rope wind it up we're going to wind it two times and see what that does for us then by holding the recoil with the housing. We're going to pull the rope slack out.
How do you replace the pull cord spring on a Husqvarna chainsaw?
3:0910:41Chainsaw Pull Cord Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo firmly grasp the take-up reel. The cord is pulled out in line with a Philips screw at my rightMoreSo firmly grasp the take-up reel. The cord is pulled out in line with a Philips screw at my right thumb carefully release the spring tension once.
How do you fix a pull start that won't retract?
0:222:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipNow to start this easy repair all you need to do is pull the cord again. Now. You might notice onMoreNow to start this easy repair all you need to do is pull the cord again. Now. You might notice on your recoil that you have a hole like this if not you can heat up a screwdriver.
How does a recoil pull starter work?
Inside the starter there is a long spring that unwinds as you pull the cord. The spring then recoils its self and pulls the cord back into the starter and onto a pulley. A simple clutch or levers/pawls let the pulley catch the crankshaft in only one direction so the pulley is free when the engine starts.
How do you put a spring in a pull start?
3:2410:26Best 3 Ways To Install A Recoil Starter Spring On A Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow if your fingers can handle it just squeeze the spring like this. And you'll have to loop itMoreNow if your fingers can handle it just squeeze the spring like this. And you'll have to loop it around it's a bit tedious. This is my preferred method here. I usually loop it really tight like this.
What is recoil spring plug?
A spring that is placed at the rear of the bolt of a automatic or semi automatic gun, that is utilized to take in or contain the recoil. The recoil spring is needed to absorb the shock of when a bullet is fired and the firearm pulls back towards the user so as to lessen the reaction of impact the user receives.
How do you fix a pull cord spring?
0:096:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this. Okay go in there like that you know catch it.
What makes a chainsaw hard to pull?
You could examine the pulley system on the chainsaw and find that it isn't working as it normally should. This could be because the tension isn't right or you might even have a weak contact between the pawl and the spring. In this case, you might need to replace parts to get the pulley system working as it should.
How do you rechain a chainsaw?
Otherwise, a flat head screwdriver and a socket wrench will do just fine.Step 1: Remove the Old Chainsaw Chain. ... Step 2: Release the Chain Tension. ... Step 3: Remove the Old Chainsaw Chain. ... Step 4: Loosen the Tensioning Screw. ... Step 5: Thread the New Chain Onto the Saw. ... Step 6: Align the Guide Bar. ... Step 7: Replace the Side Plate.More items...
What size is chainsaw pull cord?
#4 (1/8" Diameter) and #4-1/2 (9/64" Diameter) rope is used on most chain saws and larger 2-cycle engines.
How do you rechain a chainsaw?
Otherwise, a flat head screwdriver and a socket wrench will do just fine.Step 1: Remove the Old Chainsaw Chain. ... Step 2: Release the Chain Tension. ... Step 3: Remove the Old Chainsaw Chain. ... Step 4: Loosen the Tensioning Screw. ... Step 5: Thread the New Chain Onto the Saw. ... Step 6: Align the Guide Bar. ... Step 7: Replace the Side Plate.More items...
How do you put a spring on a pull start?
2:0710:26Best 3 Ways To Install A Recoil Starter Spring On A Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you want to hold it like that now grab a second pair of pliers. And just grab it the other wayMoreAnd you want to hold it like that now grab a second pair of pliers. And just grab it the other way like that. You want to end up with the pliers and the spring in this position.
How do you fix a recoil spring on a starter?
0:096:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this. Okay go in there like that you know catch it.
How do you fix the pull cord on a Poulan chainsaw?
4:225:42Poulan Chainsaw Repair - How to Replace the Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipTie an other simple overhand knot in the end of the rope I want to keep that tag end as short as IMoreTie an other simple overhand knot in the end of the rope I want to keep that tag end as short as I can pull that knot up into the opening on the handle.
Replacing The Pull Cord On A Husqvarna Chainsaw - LawnEQ Blog
Related Posts: Troubleshooting An Echo Chainsaw For Not Cutting; Winterizing Your Lawn Care Power Equipment; Common Snow Blower Problems – Pt. 1: A Snow Blower…
How to connect starter to chain saw?
Connect the starter pulley to the end recoil spring on the chain saw. Place the drive disc spring and the drive disk back into place and then insert the bolt in the pulley. Tighten the bolt with the wrench.
How to thread starter cord?
Thread the starter cord through the hole that is in the starter housing and then tie the cord into a knot.
How to release tension on a recoil spring?
Pull out the starter cord and place it into the notch on the drive pulley. Let the pulley rotate slowly backwards to release tension on the recoil spring.
How to stretch cord on a sleeve?
Remove the cord from the notch and then pull the handle to stretch the cord.
What happens if you don't tension the new start cord?
If you do not tension the new start cord, it will not engage the pulley correctly to start the engine.
Can a Husqvarna chain saw starter cord snap?
When the starter cord on your Husqvarna chain saw snaps or has become loose, you will need to replace it with a new cord. Advertisement.
What is a pull cord on a Husqvarna chainsaw?
Husqvarna gasoline chainsaw. Pull cords are commonly used to start chainsaws that run on gasoline. The chainsaw starts when the operator pulls on the cord. The cord engages the drive pulley and the chainsaw starts.
How to replace a chainsaw pull cord?
Replacing The Damaged Pull Cord: Step One: Place the chainsaw on a table or workbench. Step Two: Remove the screws that secure the starter to the side of the chainsaw. Step Three: Pull the starter out of the chainsaw. Step Four: Turn the socket wrench counter-clockwise to loosen the bolt that is in the center of the driver pulley.
How to change starter cord on chainsaw?
Step Eleven: Thread the new starter pull cord through the hole that is in the starter housing and tie the cord into a knot. Step Twelve: Place the starter pull cord into the notch on the drive pulley. Step Thirteen: Turn the pulley at least twice clockwise. Step Fourteen: Remove the cord from the notch. Step Fifteen: Pull the chainsaw- starting ...
Can you replace a Husqvarna chainsaw pull cord?
Even the pull cord that starts a Husqvarna chainsaw periodically needs to be replaced due to common wear and tear. Replacing the cord is not a difficult task. Husqvarna gasoline chainsaw. Pull cords are commonly used to start chainsaws that run on gasoline.
How to rewind a cord?
Prepare the cord for rewinding by melting the end with a lighter and rolling it around with your fingers to make a point. Move several feet away from the saw when you do this, and wear gloves.
How to stop a chainsaw from starting?
1. Set the chainsaw on a flat surface and pull the spark plug wire off the plug to prevent an accidental start-up.
How to remove starter housing from pull out?
Remove the starter housing and turn it over. Pull the knot in the center of the pull out with a pair of needle-nose pliers, cut the knot off with a utility knife, unwind the cord from the pulley and pull it out.
Why won't my chainsaw start when the starter rewinds?
Although it doesn't happen often, the recoil starter on your chainsaw may fail to fully rewind the starting cord. When that does happen, you may not be able to crank the engine enough to start it. If your chainsaw is a Homelite, the repair is uncomplicated, because the starter housing is connected to the engine by screws that are easy to find and remove. If the cord slipped out of the track, then rewinding it should restore the operation of the starter. If that doesn't work, though, you may need to replace the spring.
How to tie a pulley to a cord?
Feed the cord through the holes in the housing and pulley, and tie a knot in the end. Keep tension on the cord with one hand while you release the pliers with the other. Let the pulley slowly rewind. It will wrap the cord around itself and stop when the handle contacts the housing.
What to do if your spring is damaged?
If you find that the spring is damaged, you'll have to lift the pulley out of the housing to replace it. This can be dangerous, because the spring may still be under tension and may unwind violently. To avoid injury, wear gloves, protective clothing and goggles when you remove the pulley. Writer Bio.
What to do after replacing a recoil spring on Husqvarna chainsaw?
After replacing a broken recoil spring on a Husqvarna chainsaw, the pulley requires rewinding to tension it correctly for pull starting the chainsaw and string retraction into the starter housing.
How to operate a chainsaw?
Operate a chainsaw with both hands on the handles for proper control and safety. Start chainsaws on the ground, making certain that the cutting teeth are not in contact with the ground or any other object. Clean water, dirt and sawdust off chainsaw handles to maintain a firm grip on them.
How to replace drive disc spring?
Replace the drive disc spring and drive disc on top of the pulley. Insert the center bolt and tighten it clockwise with a screwdriver.
Where to put recoil spring on starter?
Place a new recoil spring into the bottom, center of the starter housing if the old one is broken. Set the starter pulley on top of the spring with the hook on the spring tip inserted into the slot on the starter pulley.
How to remove slack from a starter?
Grasp the pull cord handle with your left hand and stretch the cord to remove slack. Remove your right thumb from the pulley and allow the cord to retract slowly into the starter housing.