Attach the rope to the starter housing: Pass this pointed end through the starter housing hole. Tie a knot at this end of the rope to prevent it from coming out of the starter housing. Wind the pull cord: Next, remove the screwdriver and let the pulley wind the rope back completely.
How do you rewind a lawn mower starter?
Insert one end of the starter rope through the rewind and pulley holes that are aligned and out of the pulley. Tie an overhand knot in the end and pull the loose end of the rope tight to secure the knot. Hold the pulley in place with one hand and pull the screwdriver out. Loosen your grip on the pulley to allow it to rewind very slowly.
How does a Briggs and Stratton lawn mower start?
Briggs & Stratton 3.5 lawn mower engines are push mower engines with a rewind, or recoil, starting system. The rope attaches to a pulley to spin the flywheel and make the spark plug fire to start the engine. A recoil spring below the pulley pulls the rope into the blower housing after each pull.
How does a starter rope work on a lawn mower?
The rope attaches to a pulley to spin the flywheel and make the spark plug fire to start the engine. A recoil spring below the pulley pulls the rope into the blower housing after each pull. Starter ropes eventually fray, break or will not retract, and need replacing.
How do you change the pull cord on a Briggs and Stratton?
Changing the Pull Cord on a Briggs & Stratton Engine 1. Disconnect the spark plug so that the engine can't start while you're working. 2. Unscrew the decorative shroud that covers the motor housing. There are usually four hex-head screws that are easy to... 3. Locate and remove the three screws ...
How do you rewind a starter rope?
1:172:51How-To: Fix a Broken Recoil Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe can go ahead and take a paper clip open up the paper clip the paper clip is used just to assistMoreWe can go ahead and take a paper clip open up the paper clip the paper clip is used just to assist in pulling the Rope up through between the cage and the pulley.
How do you rewind a pull start spring?
0:050:56How to Rewind a Recoil Starter Spring--A Quick Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn first I just align the tab on the spring with the notch and the housing. And then I just wind theMoreIn first I just align the tab on the spring with the notch and the housing. And then I just wind the spring back into the housing. And that's how simple it is to rewind a starter spring.
How do you fix a pull start that won't retract?
0:352:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipNow to start this easy repair all you need to do is pull the cord again. Now. You might notice onMoreNow to start this easy repair all you need to do is pull the cord again. Now. You might notice on your recoil that you have a hole like this if not you can heat up a screwdriver.
How do you fix a Briggs and Stratton pull cord?
0:063:14Briggs and Stratton Pull Start Rope Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn it so it doesn't retract. And I'll show you how that is here in a second so I'll be right back I'MoreOn it so it doesn't retract. And I'll show you how that is here in a second so I'll be right back I've installed a pair of hemostats onto the rope and now I'll be able to untie the grip.
How do you recoil a pull start lawn mower?
0:171:19Replacing the Recoil Starter on a Lawn Mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition the new recoil starter in the blower housing and snap it into the retainer clips snap theMorePosition the new recoil starter in the blower housing and snap it into the retainer clips snap the recoil starter guard into place position the blower housing on top of the engine.
How do you wind a lawn mower spring?
7:538:42PushMowerRepair.com - Briggs 3.5HP Recoiling a Starter SpringYouTubeStart of suggested clipEnd of suggested clipAnd we'll get a 1 it in an anti-clockwise. Direction. We want to wind this about two times to startMoreAnd we'll get a 1 it in an anti-clockwise. Direction. We want to wind this about two times to start off with then check how you're doing for the length of the cord.
How do you tension a starter spring on a lawn mower?
0:163:31How to Tension a Lawn Mower Starter Spring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt think of which way you pull in the rope. So that you wind it the right way. And you wind the ropeMoreIt think of which way you pull in the rope. So that you wind it the right way. And you wind the rope wind the string. In you're tensioning the spring.
Why won't the cord on my mower pull?
0:102:38Lawn Mower Won't Start: Can't Pull the Recoil Starter Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou might have a problem with the recoil starter or the engine might be locked up we'll remove theMoreYou might have a problem with the recoil starter or the engine might be locked up we'll remove the blower housing to check the recoil starter on.
How do you replace the pull cord on a Briggs and Stratton lawn mower?
2:224:55Briggs & Stratton Lawn Mower Engine Starter Rope #697316 - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the rope out of the handle. Prepare the new starter rope for installation by inserting one endMorePull the rope out of the handle. Prepare the new starter rope for installation by inserting one end through the handle then tie a knot to secure.
What makes a lawn mower pull hard to start?
Some common issues that can lead to a cord being harder to pull are hydro locking, which usually occurs because of oil spilling into the exhaust area, and a misshapen crankshaft. The misshapen shaft can generally be detected due to the noise it makes.
How do you restring a lawnmower pull cord?
Prepping to Replace a Lawn Mower Pull CordLocate Your Lawn Mower's Starter Housing, Then Unscrew It. ... Carefully Remove the Starter Housing. ... Remove the Old Pull Cord. ... Measure the Old Cord, Then Cut a New One. ... Thread Your Cord, Then Tie It Off. ... Reassemble Your Device, Then Test.
How do you put a pull string back on a lawn mower?
2:165:52HOW TO Replace a Broken Lawnmower Pull Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow pull the rope like. This pull right to the other end of the rope. Now insert the starter handle.MoreNow pull the rope like. This pull right to the other end of the rope. Now insert the starter handle. Make a knot over. Here. Now you can remove the clamp. Now gently let it go back. In.
How do you rewind the spring on a Weedeater?
0:114:00How to Fix Recoil Spring the Easy Way | Husqvarna Trimmer Weed ...YouTubeStart of suggested clipEnd of suggested clipThe coil pulled tight enough to fit snugly in the center of the spool. Firmly grasp the coil in theMoreThe coil pulled tight enough to fit snugly in the center of the spool. Firmly grasp the coil in the center with your thumb and forefinger. Start winding it up by stringing the end through your hand.
How do you tension a starter spring on a lawn mower?
0:163:31How to Tension a Lawn Mower Starter Spring - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt think of which way you pull in the rope. So that you wind it the right way. And you wind the ropeMoreIt think of which way you pull in the rope. So that you wind it the right way. And you wind the rope wind the string. In you're tensioning the spring.
How does a recoil pull starter work?
In the center of the pulley, a recoil spring connects to the pulley through a hook. When the starter rope gets pulled off the pulley and out of the engine, the recoil spring stretches out. When the operator lets go of the rope, the recoil spring snaps back and the rope recoils onto the pulley.
How do you shrink a spring?
Re: How to resize a spring? Compress it. Heat it up, then compress it and douse it.
How to attach a rope to a starter?from gardentoolexpert.com
Attach the rope to the starter housing: Pass this pointed end through the starter housing hole. Tie a knot at this end of the rope to prevent it from coming out of the starter housing.
How to cut a knot on a starter?from gardentoolexpert.com
Turn over the starter assembly, and you would see the old pull cord. With the help of pliers, cut the knot on the rope.
How to remove the 3 17mm screws from a fuel tank?from ifixit.com
Use a socket wrench with a 5/16" socket to remove the three 17mm screws that keep the fuel tank attached.
How to reinstall engine shroud?from gardentoolexpert.com
Reinstall the engine shroud by tightening the bolts that hold the shroud in place.
How to hold a spool in place?from ifixit.com
Wedge a screwdriver into the gap to hold the spool in place.
What is a pull cord on a lawn mower?from ifixit.com
The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil.
How to keep rope from fraying?from gardentoolexpert.com
Burn the end of the rope: Burn one of the rope’s ends with a match stick’s help and give it a little twist. This prevents the rope from fraying. Tie a knot: Now, pass this end of the rope through the pull handle and tie a knot, which shall prevent the rope from coming out of it. – Step 4.2.
How to keep a coil from unwinding?
Wind the starting coil through seven complete rotations, and then insert a screwdriver in the coil and at the top of the housing to keep the coil from unwinding. Line up the hole in the coil hub with the one on the housing.
How to tie a coil to a housing?
Feed the cord through the hole in the housing and the one in the coil hub and tie a single knot in the end. Pull on the cord to give it tension, and then remove the screwdriver and let the coil slowly rewind. There should be enough tension to bring the handle flush with the housing.
What to do before disassembly?
Before beginning disassembly, prepare a place for the screws to keep them organized and avoid losing any.
Why disconnect spark plugs when working?
Disconnect the spark plug so that the engine can't start while you're working.
Can you cut grass with a Briggs and Stratton mower?
Changing the Pull Cord on a Briggs & Stratton Engine. Your lawn mower may be tuned up and ready to go, but you won't be cutting any grass if the pull cord is broken. It's only a minor setback, though, because the cord isn't difficult to replace, especially if the lawnmower has a Briggs & Stratton engine, as many do.
Can you replace a Briggs and Stratton lawn mower cord?
It's only a minor setback, though, because the cord isn't difficult to replace, especially if the lawnmower has a Briggs & Stratton engine, as many do. Before you begin the procedure for replacing the cord, however, the manufacturer wants you to know that the spring is under tension and can pop free when you remove the starter housing.
How to tie a starter rope?
Insert one end of the starter rope through the rewind and pulley holes that are aligned and out of the pulley. Tie an overhand knot in the end and pull the loose end of the rope tight to secure the knot.
How does a Briggs and Stratton lawn mower work?
Briggs & Stratton 3.5 lawn mower engines are push mower engines with a rewind, or recoil, starting system. The rope attaches to a pulley to spin the flywheel and make the spark plug fire to start the engine. A recoil spring below the pulley pulls the rope into the blower housing after each pull. Starter ropes eventually fray, break or will not retract, and need replacing. Replacement rope is inexpensive and the installation process takes little time and few tools.
How to rewind a pulley?
Hold the pulley in place with one hand and pull the screwdriver out. Loosen your grip on the pulley to allow it to rewind very slowly.
How to remove a pulley from a rope?
Cut the remaining rope off the pulley with scissors and remove it with needle nose pliers. Insert pliers into the rope handle and pull it out by the knot.
How to loosen a recoil assembly?
Turn the recoil assembly pulley clockwise to loosen the remaining rope. Insert a flat-head screwdriver through the pulley spokes downward to hold it in this position. This is the point of most tension on the spring and the hole in the pulley and rewind assemblies are in line with each other.
What is recoil spring?
A recoil spring below the pulley pulls the rope into the blower housing after each pull. Starter ropes eventually fray, break or will not retract, and need replacing. Replacement rope is inexpensive and the installation process takes little time and few tools.
Can you use larger rope for a replacement?
Do not use larger rope for a replacement. It can cause the recoil assembly to malfunction and the rope will not retract correctly.
