How do I troubleshoot my GE front load washer?
How to Troubleshoot a GE Front Load Washer That Won't Spin or...Remove any kinks in the drain hose. ... Inspect the household drain. ... Check the drain and make sure there is an air gap between the hose and drain. ... Clean the pump filter. ... Rearrange the clothing in the load. ... Allow the washer to cool down for two hours.More items...
How do I reset my GE front load washer?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I troubleshoot my GE washer?
How to Troubleshoot a GE Top Load WasherCheck the amount of detergent you have put in the washer. ... Examine the GE top load washer's drain hose for leaks. ... Check the water connections to your GE top load washer. ... Check whether the GE top load washer lid is closing firmly. ... Check the load in your GE top loading washer.More items...
Is there a reset button on a front load washer?
Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.29 Dec 2018
Can you reset a GE washing machine?
Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.
What are common problems with GE washers?
12 Common GE Washing Machine ProblemsGE Washer Not Filling with Water: ... Water Leaks From Fill Valve While Machine Is Running: ... GE Washer Not Starting: ... Washer Won't Drain: ... GE Washer Does Not Agitate Or Spin: ... GE washer Making Grinding Noise: ... Washing Machine Does Not Have Enough Detergent:More items...•19 Oct 2021
How do I find the error code on my GE washer?
How to Access Error Codes on GE WashersPress the "Power" button on your GE washer. ... Unplug the power cord for at least 30 seconds.Plug the power cord back in to the GE washer. ... Press "Delay Start" to advance to "t02". ... Press and hold "Start/Pause" to clear the saved error codes after viewing them.More items...
How do I know if my GE washer motor is bad?
5:0511:12Motor General Electric Washing Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the motor starts with no problem. And you want to find out the motor overheats or not let it runMoreIf the motor starts with no problem. And you want to find out the motor overheats or not let it run for about fifteen minutes on the spin cycle then unplug the test cord.
Does a GE front loader washer have a dispenser?
Also, if you press power at anytime it will exit the test mode. Some GE front loader washer models don’t have a dispenser motor but still have a dispenser test mode.
Can you diagnose a washer without service?
The way these washers are designed it is almost impossible to diagnose them without placing them in the service mode. In the service mode you have total control over the washer so that you can test components such as the motor, pump, inverter, water valve and others.
Step 1
Press the "Power" button on your GE washer. Any current cycles on the control panel will be cleared. The control panel display must be blank to proceed.
Step 3
Plug the power cord back in to the GE washer. Within 30 seconds of restoring power to the washing machine, press the "Signal" button, press the "Delay Start" button, press the "Signal" button, the press "Delay Start" button again. The washer door will lock, and the control panel will display "t01" when it has successfully entered Test Mode.
Step 4
Press "Delay Start" to advance to "t02". The control panel will display the most recent error code. Press "Start/Pause" to cycle through previous error codes. "E00" displayed in the control panel means there are no saved error codes.
Step 5
Press and hold "Start/Pause" to clear the saved error codes after viewing them.
Step 7
Press "Signal," press "Delay Start," press "Signal," and press "Delay Start" to exit the test mode of your GE washer.
Why does my washer leak?
Loose hose connections are the most common cause of washer leaks. If you suspect your leak is coming from the back of the washer, move it away from the wall a few inches and hand-tighten all hose connections between the appliance and the supply pipes.#N#The location of the leak can also give you a hint. For top-load washers, a leak from the top could be due to oversudsing or overloading (both of which are easily resolved), whereas a leak from the bottom could suggest an issue with the water pump. For front-load washing machines, a front leak could be caused by a damaged or dirty door seal, but a bottom leak is more likely to be caused by a worn drum seal.
Why won't my washing machine spin?
This is because heavy or bulky loads may unbalance the drum and eventually cause a jam. The washer will shut itself down to prevent any further damage.#N#If your washing machine fills and agitates (washes) but doesn't spin, the problem could also be with the lid switch, which tells the washer the lid is closed but may become dislodged by the vibrations of the spin cycle. In machines that have belt drives, a loose, worn, or broken belt will prevent the drum from spinning and need to be repaired or replaced. A problem with the controls, meanwhile, will definitely demand some expert attention.
Why won't my washer fill with water?
If your washer doesn't fill with water in the first phase of a wash cycle, there are only a few components that could be to blame. The hoses should be your first stop: check for kinks, blockages, or holes (which would also result in a leak), and make sure the faucets at the water supply are turned on.
Why does my washing machine smell?
Mold, mildew, soap scum, bacteria, limescale. There are plenty of potential causes of washing machine odors, and most of them can be tackled with a thorough clean. Pay close attention to seals, gaskets, dispensers (which can usually be removed for cleaning) and any other components that come into contact with laundry or detergent.
Why does my GE washer pause?
Modern GE washers all have sensors on the door latch area. If the door isn’t properly closed or can’t be kept closed, the washer will pause until the door can be properly shut. This leads to awkward pauses until you open the door to check on your clothes.
Why isn't my washer using HE detergent?
Not using HE detergent means your laundry load will be covered in way more suds than usual. All that froth and sudsing will make it hard for your washer to move, almost acting like a clog. This forces your washer to pause so that it can drain some of the suds out of your machine. Thankfully this is a good, quick fix.
What causes a GE washer to lag?
2. Bad Water Valves. Most GE washers will have two different water valves: a hot water valve and a cold one. If you have a clog or a leak in either water valve, your washer will begin to lag and pause.
What detergent does GE use?
All GE machines need to use HE detergent, also known as “High Efficiency” detergent . If you recently switched detergents, check to see if the new brand is considered to be HE. (It’ll write it on the front of the jar.) Not using HE detergent means your laundry load will be covered in way more suds than usual.
Why does my GE washer stop working?
There are several major reasons why a GE washer may end up stopping. Most of the time, this is due to a blown motor or a bad pump that runs the machine . However, it can also be caused by a glitchy computer system as well as a bad failsafe.
What does water level control do?
The water level control is what sends the “call” for more water. These two have to work together in order to make sure water levels stay regular. If the water pressure sensor is off, then the washer won’t be able to figure out when to ask for more water or if the washer is fully loaded with water.
Why does my front loader pause?
The most common issues include: Those pauses often happen for pretty worrying issues. In order to fix (and hopefully prevent damage to) your GE washer, you’re going to need to know how to troubleshoot and fix things.
