How do you run a sprinkler line?
- Step 1: In-Ground Sprinkler Overview. ….
- Step 2: Dig the Trenches. ….
- Step 3: Make the Water Connection. ….
- Step 4: Install the Zone Valves. ….
- Step 5: Place the Pipes in the Trenches. ….
- Step 6: Connect the Pipe at the Valve Box. ….
- Step 7: Install the Pop-Up Sprinklers. ….
- Step 8: Roll Out the Irrigation.
How do you move a sprinkler line?
Before we can move the line, we must plan out the new sprinkler line layout according to your landscaping needs. First, we analyze your landscaping to determine where to place the new line so your foliage receives adequate hydration. 2. Locate the Origin of the Line To move a sprinkler system line, we must first locate its origin.
How deep does a sprinkler line need to be?
The trench for a sprinkler line is usually about 8 to 12 inches deep. The width of the trench should be between 4 and 6 inches. The trench may contain two pipes. One for the water and another to contain the sprinkler wire. It is not compulsory to have two pipes as the wires may not be put in a pipe.
How do you flush a sprinkler system?
To do this, we perform a simple water flush, which involves removing the sprinkler heads and turning on the water source. After flushing the pipes, we replace the sprinkler heads and turn on the water to check for any leaks.
Where are the valves on a sprinkler system?
Within your sprinkler system, there are a set of valves that controls each sprinkler line. Those valves are typically housed in a plastic box below ground, typically identified by a round green plastic top. We trace the existing line to its origin at the valve and cut it at the point of attachment.
How do I run a new sprinkler line?
3:194:59How to Install a Sprinkler System | A DIY Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you've made sure the pipes don't leak turn on your zone valve. And sit back and watch yourMoreOnce you've made sure the pipes don't leak turn on your zone valve. And sit back and watch your plants get. Water. Then you can just back fill in your trench.
Can I install sprinkler system myself?
Installing your sprinkler system is doable if you're willing and able to put in the work and time required to do it right. However, it is one of the more challenging projects a homeowner can take on themselves. Even experienced DIYers may need a plumber or electrician to complete certain aspects.
How many sprinklers can I run on one line?
With your 10 gpm flow rate at your spigot, you could run two sprinklers at 5 gpm each. The best set-up is to run two hoses from the spigot–each to one sprinkler. Suggested sprinklers for this set-up are the Residential Sled Base Sprinklers or the Tripod Sprinklers.
How deep do you dig sprinkler lines?
Dig for Your Sprinkler System The trenches will be relatively shallow, usually 6 to 12 inches deep, depending on your area's freeze cycles and frost severity. The trench must also be deep enough to allow the sprinklers to retract underground to prevent breakage from lawn machines.
How many sprinkler heads can you put on a zone?
If your home's water capacity was 10 GPM, you could place 3 heads per zone.
How many zones do I need for my sprinkler system?
How Many Irrigation System Zones Do I Need? Most irrigation systems have nine zones or less. It's pretty common to have 6-9. Part of it boils down to your water source, and how much water it can pump out.
Which pipe is best for sprinkler system?
Many types of piping are available for irrigation systems, but PVC Schedule 40, Pressure-rated PVC, and black roll pipe are suitable for this use. Drain, waste and vent (DWV) PVC is not suitable due to a low pressure rating. Other piping types are either too expensive or too difficult to work with in the landscape.
What size sprinkler line should I use?
That number is flow rate in terms of gallons per minute, or GPM. For schedule 40 PVC, use 1/2-inch pipe for a 4 GPM system, 3/4-inch pipe for 8 GPMs, 1-inch pipe for 13 GPMs, 1 1/4-inch pipe for 22 GPMs, 1 1/2-inch pipe for 30 GPMs, and 2-inch pipe for 50 GPMs.
How do you layout a lawn sprinkler system?
Sprinkler heads should always be placed so that the sprays overlap—the distance one head throws should reach the head of the next sprinkler. This is called head-to-head coverage, and sprinklers should be placed equidistantly in each zone to achieve it.
How do you dig a trench for underground sprinklers?
Dig Trenches By Hand: To soften the soil, water the ground approximately two days before you dig. Dig trenches 8 to 12 inches deep. Put sod on one side of the trench and soil on the other. Note: Before digging any trenches, you must have all underground utilities marked to avoid any damage.
How far apart should sprinkler heads be?
The absolute number one rule in spacing is called “Head-to-Head coverage” or Head-to-Head spacing. Head-to-Head coverage applies to both sprays and rotors. In a nutshell, it means that the heads are spaced so that they overlap from head to head. Each head should throw water far enough so that it hits the next head.
How Far Should sprinklers be from house?
2 feet awayMake sure sprinklers don't spray your house, especially the windows, or over window wells. Keep the spray at least 2 feet away from the house.
How much does it cost to put in a sprinkler system?
National Averages According to Home Advisor, the national average for a new sprinkler costs $2,429. At the lower end of the scale, the cost is $500, and the high end is $5,000. The typical cost for an irrigation system ranges from $$1,697 - $3,530.
How do I install an above ground sprinkler system?
2:069:47DIY above ground Sprinkler System...NO DIGGING!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere we have the hunter pro-spray in-ground sprinkler head. And what we do is we connect it to aMoreHere we have the hunter pro-spray in-ground sprinkler head. And what we do is we connect it to a lawn spike that has 1/2 inch hose connectors. And then you take this MP rotator.
Can you install sprinklers on existing lawn?
You can! With the proper equipment and care an in ground sprinkler system can be installed without making a mess of your existing lawn. Follow these steps for a seamless installation.
How do you tap a water line for a sprinkler system?
0:416:31Tapping Into the Main Line - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd on the supply side pipe push on the tee fitting and twist it into a 45-degree upward angle aboutMoreAnd on the supply side pipe push on the tee fitting and twist it into a 45-degree upward angle about five feet of service line has been dug up after the tee.
Why do people have sprinkler systems?
Having a sprinkler system is great. It helps everything grow better, and it’s extremely convenient. That’s why so many people have them installed. These systems do have a caveat though. When your system is buried underground, it can be hard to know exactly where the lines are located. If you need to do some digging in the yard, you certainly don’t want to put a shovel through your lines. Also, when the lines need service, it’s vital to locate them so you don’t have to dig up the whole lawn. For these and other scenarios, Andy’s utilizes a few tricks to find the buried lines.
Why do we dig around sprinkler heads?
We also sometimes have to dig in order to be sure we have found the part that needs work. It’s common to do light digging around sprinkler heads to find a leak, or we might have to dig up valves in order to diagnose them (or install a box).
Do sprinkler heads have to stick out?
Your sprinkler heads have to stick out of the ground or they won’t work. This is great for us as it gives us something visible to identify. Once the heads are marked in a grid, we know that the water lines have to run between them. A small amount of probing or digging around each head allows us to verify the direction of the lines, giving us a solid picture of the layout of your system.
Can you contact Andy's Sprinklers?
If you need to know where your lines are, we can help you locate them. If you need any other work with sprinklers or drainage, we’re here for you. You can contact Andy’s Sprinkler, Drainage and Lighting at any time. We’re always happy to help.
Do you have to dig up a sprinkler line?
Ultimately, most sprinkler work requires digging. If we need to access a line or other component beneath the ground, we have to dig it up; there really is no other way. Everything we’ve illustrated in this article allows us to dig as little as necessary to do the work, but digging is always the final step.
Prepare for Your Sprinkler System
Living landscapes need water to survive and flourish, but relying completely on natural rainfall isn't always a reliable way to supply water. An underground sprinkler system offers the convenience of spraying water directly where it needs to go and the opportunity to automate your watering schedule according to your needs.
Determine the Water Pressure
There are two measurements of water pressure: working (when the water supply is turned on) and static (when the water supply is shut off). You'll need a pressure gauge to determine your working water pressure number. The gauge attaches to the outside faucet and provides a pressure reading in PSI.
Determine the Water Meter Size
If you're on a municipal water system, you should find the size printed on the meter itself. If you can't locate it, look on your utility bill or call your water provider. Water meters are 5/8 inch, 3/4 inch or 1 inch.
Determine the Service Line Size
To match the size of the irrigation pipe to your existing water service, you'll need to determine the size of your incoming supply line. To do so, get a piece of string and wrap it once around the water pipe. Measure the length and compare it to the chart below.
Map the Sprinkler System
When you've completed all of the preliminary research, it's time to start laying out your system. Most yards have a variety of elements that have to be considered when laying out an irrigation system:
Plan the Coverage
When installing a sprinkler system, 100% coverage is essential to avoid dry spots. You can achieve this by overlapping the spray pattern. Head-to-head coverage refers to the sprinkler head layout that allows spray from each sprinkler head to reach the adjacent head, ensuring overlap.
Know the Primary Parts
Done with the planning? Take your water measurements and maps with you when shopping for parts. You'll need to select your system components to match your water supply and water pressure. A mismatch will either stress the system or provide insufficient irrigation.
How do you trench a sprinkler line?
A sprinkler line is buried in trenches below the soil surface. The course of the sprinkler must first be decided through mapping of the area. This can be done by first deciding the capacity of the sprinkler head and how much area is to be covered by each.
What is the primary pipe for a sprinkler system?
Pipes for conveying the sprinkler line and the water pipes are primary for the job. To end the day without blisters and cuts, hand gloves are advised.
How deep should a trench be?
The trench should be about 8 to 12 inches for a mild climate region. It can be as deep as 18 inches in places with freezing climates. The digging can be done using a shovel, ensure to avoid destroying sods if you have grass cover already.
How deep is a sprinkler trench?
The trench for a sprinkler line is usually about 8 to 12 inches deep.
How deep should a trench be for a frost line?
In such climates, 18 inches deep trenches are more appropriate. The increased depth is to allow the line to convey water without it freezing up. The digging should put the pipes below the frost line. It may be instrumental to contact environmental authorities for the recommended depth below the frost line.
How long does it take to dig a trench?
Averagely, digging trenches may take up to 2 or more hours. Consider that the planning of the course is also an important part of the process. For about 10 feet long trench digging, about an hour of work is needed.
What is used to lay a bed under pipes?
The trenches are covered with soil. Medium-sized pebbles or sand can be used to lay a bed under the pipes before finally covering them with soil.
