How to Fasten a Downspout to Vinyl Siding
- Step 1. Fasten the downspout to the gutter elbow with sheet metal screws according to the manufacturer's instructions.
- Step 2. Place a downspout strap at the top where it meets the elbow. Secure one end of the strap to the siding with a...
- Step 3. Bend the strap across the downspout and secure the other end to the siding with a...
How do you attach a downspout to vinyl siding?
Downspouts can be attached to houses with rivets or metal screws. In the case of installing a downspout onto vinyl siding, a metal screw is used to secure it to the house. Using screws allows you to periodically take apart the downspout to clean it, which will prevent the gutters from backing up and sending water into your home.
How do you seal gutter downspouts on siding?
To provide continuous protection to siding it is strongly recommended that a silicone compound be applied around and in the holes drilled to apply clamps for securing the gutter downspouts. Simply insert a caulking silicone compound into a caulking gun and apply it to all the holes drilled to secure the clamps for the downspouts.
How do you attach gutter downspouts to stucco?
Drill a hole wide enough for the anchor, tap it into the stucco, and then attach the downspout clamp and screw a #6, 2-inch screw into the anchor. To provide continuous protection to siding it is strongly recommended that a silicone compound be applied around and in the holes drilled to apply clamps for securing the gutter downspouts.
Can you drill into vinyl siding?
Obviously, you want to be safe when climbing ladders to drill into the siding. Make sure that your ladder is secure and that the cord for your drill is clear of your work area. You probably will find that cordless drills will work just fine. Vinyl siding is easy to penetrate, but there are places you want to avoid within the profile of the siding.
How do you hold downspouts in place?
When the downspout is in place, wrap the strap around the downspout from both sides. Pull the strap tight so both sides of the strap are overlapping. Place one screw into the center of the overlapping straps.
How do you stabilize a downspout?
0:451:40How to Repair a Downspout - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd all you need to do is use a regular pop rivet tool with color-coded pop rivets that match yourMoreAnd all you need to do is use a regular pop rivet tool with color-coded pop rivets that match your work install. The pop rivet into the tool pull the handle of the pop Riveter and bingo the job's.
How do you attach a downspout to the side of a house?
0:011:21How To Install A Downspout Strap - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically all you do you can get them 1/4 inch diameter and then you pick up a quarter inch concreteMoreBasically all you do you can get them 1/4 inch diameter and then you pick up a quarter inch concrete bit and drill a hole that with this will fit in put the strap.
How do you keep downspouts from falling off?
The downspout must be attached to the side of the home to prevent it from falling. Use caulk to create a strong seal between the gutter and the downspout. After the caulking has dried, test your new gutter and downspout system....Hours.Monday9:00 AM - 5:00 PMSaturdayClosedSundayClosed4 more rows
What screws to use for downspouts?
1 1/2″ Hanger Screws W/HEX Bit The 1 1/2″ hanger screw by Raytec is the best screw to use while fastening a downspout strap to the wall of a home. Pro's use the 1 1/2″ gutter screws on every downspout strap regardless of the home exterior materials.
What do you put under a downspout?
Extending Gutter Downspouts: 6 Ideas for Better Downspout...Aluminum Extension. This one's a popular solution for a few good reasons. ... Buried Drain Pipe. ... StealthFlow. ... Decorative Splash Blocks. ... Roll-Out Drain Sleeves. ... Rain Barrel.
How do you attach an elbow downspout?
1:052:18How To Install Downspout Elbow On A Gutter System ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSection drill and insert two pop rivets on each side. Make sure the rivets penetrate both theMoreSection drill and insert two pop rivets on each side. Make sure the rivets penetrate both the straight downspout and the elbow.
How do you secure downspout extensions?
0:201:26How to Use Downspout Extenders to Protect Your Foundation - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater this version is installed by removing the elbow and slipping on the extender. Its held inMoreWater this version is installed by removing the elbow and slipping on the extender. Its held in place with a couple of screws.
How far apart should downspout brackets be?
Gutter Hanger Spacing Is Critical As a rule of thumb, gutter hangers should be spaced a maximum of three feet away from each other. If you live in a cold climate, your contractor may recommend gutter hanger spacing of two feet apart to account for the additional weight from snow and ice.
How do you fasten downspouts to gutters?
Screw a downspout elbow to the outlet tube protruding down from the gutter. Hold another elbow against the house and cut a piece of downspout to fit between the two elbows. Use needlenosed pliers to slightly crimp the elbow to fit into the downspout (as shown). Fasten the parts together with pop rivets or screws.
How do you reattach a gutter downspout to the house?
2:537:23How to Repair a Downspout properly, To get properly flowing Gutters!YouTubeStart of suggested clipEnd of suggested clipYou'll need to drill back you got a quarter inch drill bit you're going to attach with this quarterMoreYou'll need to drill back you got a quarter inch drill bit you're going to attach with this quarter inch hex head screw on the top screw head if you come over to here.
Do downspout extensions work?
So, will extending the downspouts help? Yes. And you should absolutely extend the downspouts away from the home. But they are rarely the only solution needed to solve a water problem in the basement or crawl space.
How do you secure downspout extensions?
0:201:26How to Use Downspout Extenders to Protect Your Foundation - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater this version is installed by removing the elbow and slipping on the extender. Its held inMoreWater this version is installed by removing the elbow and slipping on the extender. Its held in place with a couple of screws.
How do you fix a bent downspout?
1:414:43How to DIY Fix a Metal Downspout Extension Quickly Repair Dented ...YouTubeStart of suggested clipEnd of suggested clipRight you can actually use the power of the clamp to try to mold that back into place and so theMoreRight you can actually use the power of the clamp to try to mold that back into place and so the process here for me was to kind of find where that footprint was that crushed part of the downspout.
How do you fix gutters with standing water?
In most cases, the ideal solution is to simply install an additional downspout in the location where the problem is present. This will facilitate the draining of any accumulation of standing water. For rainwater to properly flow when entering into down spouts, it is essential for gutter pitch to be correct.
How do you adjust the slope on a gutter?
1. To adjust the slope of the gutter, wearing gloves, pop out the gutter pegs on the side and around the corners. Loosen the drip edge with a screwdriver. Use a hammer and crowbar to loosen the gutter.
How to crimp a downspout?
Crimp the corners of the top end of the downspout piece with needle-nose pliers by grasping each corner with the pliers and twisting the metal in towards the downspout center.
Where to put aluminum sealant on gutter?
Run a bead of aluminum sealant caulk around the edge of the connector where it sits in on the top side of the gutter opening.
What is an aluminum downspout?
Aluminum downspouts direct water collected by gutters away from the house and towards the ground. Downspouts can be attached to houses with rivets or metal screws. In the case of installing a downspout onto vinyl siding, a metal screw is used to secure it to the house. Using screws allows you to periodically take apart the downspout to clean it, ...
How to measure elbows for downspout?
Hold the second elbow up to the side of the house with one opening facing towards the free end of the first elbow. Measure the distance, in a straight diagonal line, between the two elbow ends. Add three inches to the measurement and cut a piece of downspout to this length with a hack saw.
Can you use screws to secure a downspout?
However, if the siding to which the downspout is to be attached to is stucco or other material, it will be necessary to carefully consider the use of various anchors which will accept screws and expand, thereby securing the downspout, while also leaving as small an opening in the siding as possible. This will protect the siding from the intrusion ...
Can you attach downspouts to siding?
Knowing how to attach downspouts to different siding materials can be very useful information, especially if you attempting this project by yourself. Although seemingly difficult, the novice homeowner can save a lot of money with this simple project which can usually be finished in a weekend with a minimum of skills, tools and required materials.
How many screws do you need to attach a downspout?
When the downspout is set in place FIG. 5, it takes only two sheet metal screws through the holes 18 in the foldable arms 16 to attach clip to downspout.
What is a plastic downspout clip?
A molded plastic attachment clip with a lip at the top and angles leading back to siding, and back again to main body of clip causing a positive lock when inserted into the locking mechanism of vinyl siding, with two foldable arms to hold gutter downspouts in place without nailing or damaging the vinyl siding. This unique locking system allows for easy aligning of downspouts after installation, and does not void the warranty of vinyl siding as does present method of strapping downspouts.
Do you need to puncture a hole in vinyl siding?
It is no longer necessary to puncture any holes in vinyl siding to attach a downspout.
Can clips be painted to match siding?
Although the above description contains many specifications, these do not limit the scope of the invention but merely act as illustrations of some preferred embodiments of this invention. For example, the clips will be molded to exactly match most vinyl siding colors, and can also be painted to match the downspout.
How to expand a hole in siding?
If concerned about penetrations, drill a hole for the screws and apply a dab of silicone adhesive sealant to the hole prior to fastening. Expansion; we're only talking about an area of about 3 inches between screws so a couple of thousandths expansion won't be a problem. When installing siding a larger distance is accompanied with that application and more important to allow for expansion.
Is it OK to install vinyl siding with spacing?
If that's so and it's OK it makes you kinda suspect of how very specific people are about installing vinyl siding with spacing and fasteners designed to allow movement, as well as people saying how important it is have no imperfections in your wall membrane...
What causes rust on vinyl siding?
One of the worst things to see on vinyl siding is a streak of rust flowing down from a plain drywall screw. No matter where you live, moisture will cause regular screws to rust and many times the rust shows up rapidly. Even some galvanized screws will rust over time, but there is a secret to choosing the right product.
What happens if you miss a screw in a vinyl sheet?
If you miss and the screw is only in the vinyl field, it will work loose and leave a bigger hole and can cause whatever you are hanging to fall and break. Another area is the vinyl trim found on beams and eaves. This is a flat metal sheet with vinyl covering. Trim is normally applied over solid areas.
Can you penetrate vinyl siding?
Vinyl siding is easy to penetrate, but there are places you want to avoid within the profile of the siding. For siding that has two sections, called "ship lap," there is a rib running horizontally in the middle of the piece. Trying to place the screw through that middle rib can be awkward.
Can you put Christmas lights on vinyl siding?
Most homeowners who are lucky enough to have vinyl siding find that sooner or later something needs to be attached into the siding or trim. Christmas lights are a great example or maybe a hanging plant. Many times rather than using nails, screws of various sizes are required, and preferred.