- Take out each of the taillights. In order to spray your taillight, you will first need to remove them from the car.
- Sand the taillights. Before spraying your taillight, you will first need to sand them to provide a completely smooth surface for the spray tint.
- Place masking tape over any areas you don't want to spray. In most cases, this will be the reverse light, which must remain untinted according to several state laws.
- Apply the spray tint. Once the lights are completely dry and you have masked off the applicable areas (if necessary), place the tail lights on a stable work surface ...
- Apply the clear coat. The process of applying the clear coat is very similar to applying the spray tint.
- Sand the tail lights again. Once the taillights are completely dry (this may take a couple of hours) you will need to repeat the sanding process.
- Apply some rubbing compound. Once the taillights have been evenly sanded, get some rubbing compound and apply a generous amount to an application pad or clean cloth.
- Polish and wax the lights. Once you have finished applying the rubbing compound, wipe your tail lights down with a microfiber cloth, then use the same technique to apply ...
- Replace your tail lights. Once your tail lights have been waxed, they are ready to be reinstalled in your vehicle.
How do you remove spray tint from tail lights?
To get it off, we used rubbing alcohol and immediately put detailing spray or wax afterwards. It worked pretty well. 3 level 1 OriginalHulk · 5y Goof Off. Try that, and see what happens. 1 level 1 TheRagCompany · 5y The Rag Company Vendor There are a few different versions of this kind of spray-tint stuff out there.
How do you tint a tail light?
Method 2 of 3: Tint the tail lights with film
- Heat gun or hair dryer
- Microfiber or lint-free cloth
- Sharp utility knife
- Small vinyl squeegee (choose a small handheld squeegee)
- Spray bottle of water
- Window tint film of the desired darkness (For example, you can use 5%, 30%, or 50% film tint)
How to tint your taillights like a pro?
Method 1 of 3: Use spray tint to tint your tail lights
- 2,000-grit wet-sanding paper
- Can of clear coat
- Can of tint spray
- Car polish
- Car wax
- Lint-free cloths
- Masking tape
- Pail with 1 gallon of water and 5 drops of dish soap
- Sharp utility knife
Should I tint my tail lights?
Should I tint my tail lights? A taillight is for making yourself visible to other drivers. Tinting your taillight decreases your visibility = reduced performance. To all that do not agree. I suppose you are also the ones driving in the rain or fog with no lights on.
How long does it take to spray tint tail lights?
Apply the spray tint. Leave this first layer of tint to dry for 20 to 30 minutes. Once the first layer of tint is dry, you can apply a second layer of tint. When you are done, let the lights stand for 20 to 30 minutes until they are dry to the touch.
How do you smoke tail lights with spray paint?
2:555:03DIY: Smoke / Tint Tail lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou should be spraying. Between eight to ten inches away and parallel to the taillight as well. SoMoreYou should be spraying. Between eight to ten inches away and parallel to the taillight as well. So as the taillight curves your hand must curve with the taillight. After you've practiced.
How do you spray tinted tail lights on rustoleum?
1:443:02Rust Oleum Lens Tint How to Apply - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to hold the can about 10 to 16 inches from the lens. Then in steady even back and forthMoreYou want to hold the can about 10 to 16 inches from the lens. Then in steady even back and forth motions slightly overlap each pass. It's important to keep the can in motion while spraying.
Can you spray paint your taillights?
2:247:55How to custom paint tint your tail lights - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you want to get that kind of color just go to your local paint supplier or paint shop even askMoreSo if you want to get that kind of color just go to your local paint supplier or paint shop even ask a panel shop in your area ask them to give you a clear base coat with ten percent flat.
How do you smoke your tail lights at home?
0:563:53How To Smoke Tail Lights Yourself - YouTubeYouTubeStart of suggested clipEnd of suggested clipAlright in this video we're going to smoke our tail light so the first thing we're gonna do is sendMoreAlright in this video we're going to smoke our tail light so the first thing we're gonna do is send our lenses with 2,000 grit water sand. Next step we want to make sure we dry it. Good.
How do I blacken my tail lights?
2:124:06How To Tint Tail Lights | Easy Guide | Blacken Headlights - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen once you have the colors match just let it sit and dry for 30 minutes I'll show you guys whatMoreThen once you have the colors match just let it sit and dry for 30 minutes I'll show you guys what it looks like when it's come down I'll apply the clear coat after you're.
How do you apply spray tint?
0:131:39Rust-Oleum Lens Tint Spray - How to Tint Car's Light - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to hold the can about 10 to 16 inches from the lens. Then in steady even back and forthMoreYou want to hold the can about 10 to 16 inches from the lens. Then in steady even back and forth motions slightly overlap each pass. It's important to keep the can in motion while spraying.
What is the best tint for tail lights?
Plasti Dip. Tint film is the most accurate type of tint to apply to your tail lights and gives your tail lights a seamless finish. Tail light film is also durable and protects your tail lights from cracking.
How much does it cost to smoke tail lights?
For professional results, you can receive a perfect fit tail light tint job for between $65 and $150 per lens at the wide range of pricing. This is based on the vehicle and the shape and size of the tinted tail lights.
How long does it take for spray tint to dry?
DRY & RECOAT Dries to touch in 20 minutes, to handle in 1 hour and is fully dry in 24 hours. Apply a second coat within 1 hour or after 24 hours.
Can I use window tint on my tail lights?
If you are on a budget and still want to create a personal identity with your car, you can do so by tinting your tail lights yourself. Warning: Tint laws vary from state to state. You can check your state's tint laws at Solargard.com to determine if it is legal to tint tail lights in your area.
Should I tint my tail lights?
The tint protects the car lights from damages, scratches, chips, or road debris. It reduces the risk of lights becoming yellow, filthy, and toneless because of dirt and UV rays. Most of the headlight or taillight tints have superior UV and temperature resistance.
How do you lightly smoke headlights?
1:2013:37HOW TO TINT/SMOKE HEADLIGHTS (CHEAP!!) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt around the light right. So if you can see the light here here I'm gonna oversize it and make sureMoreIt around the light right. So if you can see the light here here I'm gonna oversize it and make sure it can cover the light.
How do you make smoked headlights?
The 5 Steps To Smoking Your HeadlightsStep 1 – Cleaning the Lens. What is this? ... Step 2- Applying the Backing Paper. You will look at the shape of your headlight when you do this. ... Step 3 – Removing the Backing Paper. You will want the headlight to be dry. ... Step 4 – Taping and Getting Tint. ... Step 5 – Final Process.
Can I tint my tail lights with window tint?
the tint film you see some using on lights is a translucent vinyl, this can stretch & conform a bit better, still not going to work great for the tails but at least you'd have half a shot with that, no chance of getting this to work with window tint....
Can you spray tint headlights?
1:1013:49Tint Your Lights DIY! Spray Headlights & Tail Lights Tinted [Super Seicento]YouTubeStart of suggested clipEnd of suggested clipLook I'm after for the exterior of the car to fix that I'm gonna be using spray. Light tin and todayMoreLook I'm after for the exterior of the car to fix that I'm gonna be using spray. Light tin and today I'm gonna show you how to spray tin all the lights on. Your car quick disclaimer tinted lights aren
What is the best way to tint tail lights?
Film tint is a great option for tinting your tail lights, as it allows the light through the tinting, but restricts the light that comes back in. There are many different types of film tint available both online and in car accessory stores.
How to tint tail lights?
Once the lights are completely dry and you have masked off the applicable areas (if necessary), place the tail lights on a stable work surface to begin the spraying process. Give the can of spray tint a vigorous shake, then hold it about seven inches away from the light, for best coverage. Spray a light, even layer all over both tail lights, making sure both lights achieve the same color. Leave this first layer of tint to dry for 20 to 30 minutes.
How to remove taillight film from plastic?
Remove the film tint from its protective sheet. Peel the film tint from the protective plastic sheet and spray either some soapy water or a solution of 85% water and 15% rubbing alcohol in a spray bottle on the adhesive side. This will prevent the film from sticking before you have properly aligned it on the taillight.
How to clean taillights with paper towel?
Wet a piece of 800 grit sandpaper and rub it against the taillight until the surface is dull and scuffed up. You can use a little dish soap if you like. Repeat the sanding process for each taillight. When you're done, wipe the lights clean with a cloth or some paper towel and allow them to dry.
How long do you wait to spray on a clear coat on a car?
Then, spray the lights with a spray-on tint using a back and forth motion to apply an even layer. Wait at least 1 hour before applying a clear coat. Finally, reinstall the tail lights. You can also tint your tail lights using tint film. First, clean your tail lights thoroughly with soap and water and wipe them dry.
How long does it take for tail lights to dry?
Spray a light, even layer all over both tail lights, making sure both lights achieve the same color. Leave this first layer of tint to dry for 20 to 30 minutes. Once the first layer of tint is dry, you can apply a second layer of tint. When you are done, let the lights stand for 20 to 30 minutes until they are dry to the touch.
What to use to clean a light fixture?
Give the lights a wipe down with some cleaning product - such as rubbing alcohol, gasoline, or window cleaner - and allow the lights to dry.
How to get scratch off taillight tint?
For taillight tint kits with slits spray the outside of the film with solution again. This will reduce scratching. Spray the light once again. Proceed as above being sure to liberally apply the solution to both sides of the film. When the film is stretched into position one of the sections or flaps of the film will naturally fall over the other. Lightly smooth the flap down until flat. Using a razor gently score away the overlapping film until you can easily pull the excess film away.
How to clean taillights with alcohol?
For proper adhesion, clean all surfaces using a 2:1 mixture of water to isopropyl alcohol or Rapid Prep.
How to apply Rapid Tac to a light?
Spray a liberal amount of the Rapid Tac onto the light which will allow you to reposition the film during the application process. Be sure to include gaskets and trim around the lights as well.
How to get rid of scratching on a film?
Spray the outside of the film with Rapid Tac of the soap and water solution again. This will reduce scratching. Spray the area once again to allow repositioning.
How to use Rapid Tac on tint?
As always, mist your fingers, and spray the Rapid Tac on the tint as well.
What is a precut taillight tint?
Precut tail light tints are the perfect way to upgrade, protect and restyle your vehicle's taillights. Precut to fit your year, make, model and sub-model and sold as a pair, they are the ideal way to do-it-yourself and save. If playback doesn't begin shortly, try restarting your device.
How to fix scratches on a light?
This will reduce scratching. Spray the light once again. Apply pressure to the center of the film on the light with a squeegee so that it begins to adhere to one end of the light. It may be easier to have a partner help you by holding the film as you begin the next step. Gently begin to heat the film on one end from the center with a hair dryer or heat gun on a low setting. Take your time in heating the film, you do not want to melt the film.
How much does it cost to get your tail lights tinted on average?
If you want to spray your own tail lights, you will spend about $20 on the paint, sandpaper, and other accessories. If you would like to have the paint professionally applied, then you can expect to pay anywhere from $65 to $150 per lens.
How much does it cost to tint brake lights?
If you are looking to apply tint to your brake lights, then you can expect to pay about $40 for the cost of the tint as well as other associated accessories. If you opt to have the tint professionally applied, then you can expect to pay anywhere between $65 to $150 per lens .
What is the difference between tinted and smoked tail lights?
The main difference between both approaches depends on the overall effect of the light passing through the lens. When it comes to smoking the light, the appearance of the tail light will not be as dark as the tint. Tinting will allow for a darker appearance. However, with both approaches, you will be reducing the amount of light that passes through the lens.
Will tinted tail lights pass inspection?
Tinted tail lights will pass inspection under several conditions. First, tinting tail lights should be legal in the state where the vehicle is registered. Also, the light must meet the minimal allowable viability. Finally, the tail light may have to pass various appearance standards set by that state’s Department of Motor Vehicle.
Is it illegal to tint tail lights?
For instance, New York, Iowa, California, Virginia, and Hawaii have overall strict limits on window tinting. In New Jersey, New Hampshire, and Vermont, tinting any part of a vehicle is illegal. This includes the taillights.
Can you tint your car's tail lights?
Most car owners, who are looking to modify their vehicle, often ask, “Can you put window tint on tail lights?” The simple answer is that some states do not allow any form of tinting of your tail lights . In the states where it is legal to tint your lights, you will have to make sure that you allow for the minimum required amount of illumination. For instance, in certain states, the tail light will have to emit at least 24% of light with the tinting applied. No matter which states that you are in, all tail lights must be DOT compliant.
Can you put a window tint on brake lights?
While it is possible to use window tint on tail lights, it is not recommended. That is because window tint does not stretch very well. This will make it hard for the window tint to conform around any curves on the tail light. If you are looking to use tint for your tail lights, then it is better to apply a film designed for light application.
How to tint a tail light with water?
Step 2: Mist the tail light with water from your spray bottle. Use the spray bottle to wet the tail light surface. This will allow you to attach the tint film. Step 3: Remove the protective layer from the tint film. Take of the protective layer from the adhesive side of the tint film.
How to clean a tail light?
After you remove the first light, repeat the Steps 1-4 on the other tail light. Step 6: Prep the tail light surface. Wash the tail light with the water and soap, and then dry them completely afterwards. Soak the 2,000-grit sandpaper in the water and soap while you wash the tail lights. Step 7: Mask the reverse lights.
How to remove tail lights from car?
The removal procedure for the tail light is generally the same for every car, but some models may have slight differences. Open the trunk and pull the stiff carpet liner away from the rear of the trunk where the tail lights are.
How long does it take for a clear coat to dry on a tail light?
In the same manner as the tinting spray, apply clear coat to the tail light. Apply light, complete coats to the tail lights with each pass. Allow 30 minutes to dry between coats. Tip: Spray at least 5 coats of clear coat onto your tail lights. 7-10 coats is optimal for a uniform, protective finish.
How to smooth out tailgate edges?
Use the squeegee, your finger, or a credit card to smooth the edges out and tuck them in around the tailgate to complete the process.
How to cover reverse light?
Cover the reverse light area completely, then trim it precisely to size with your utility knife. Use light pressure as you don’t want to gouge into the light too deeply.
Can you tint your tail lights yourself?
If you are on a budget and still want to create a personal identity with your car, you can do so by tinting your tail lights yourself. Warning: Tint laws vary from state to state. You can check your state’s tint laws at Solargard.com to determine if it is legal to tint tail lights in your area.
