Pull the starting cord several times. The starting cord should be on the base of the lawn mower, and will have a plastic cord to grasp. Hold onto this firmly, and give the starting cord a single smooth, long pull upward. Do not jerk or yank on the cord. Pull quickly until the cord has fully extended.
Full Answer
Why won't the pull cord on my lawn mower pull?
Debris in the Lawnmower Deck Something might be stuck in the deck, meaning the lawn mower blade won't turn. If your blade is bolted onto the crankshaft and the blade is wedged, then the pull rope will not pull. A stick, rock, or garden hose could be the cause.
How does a pull cord start an engine?
The operator pulls the rope's handle or grip. This causes the rope to unwind around the crankshaft and spin it. The spinning motion of the crankshaft cranks the engine. The crankshaft's motion engages the flywheel, enabling the engine to start.
What is a pull start connected to?
Most small engines use a starter cord that you pull by hand. The cord is attached and wound. around the flywheel or a pulley attached to the crankshaft.
How does the pull cord on a lawn mower work?
The starting cord is wound around a spring-loaded hub that is designed to engage with the engine flywheel. When you pull the cord, the flywheel rotates, which in turn rotates the crankshaft and moves the piston. A magnetic coupling on the flywheel causes the spark plug to fire cyclically as the piston moves,.
What does it mean when your lawn mower won't start?
Your Mower Won't Start: If you have last season's gas in your mower, drain your fuel tank and fill with fresh gas. Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace.
How does a push mower starter work?
Not only does the lawn mower starter turn the engine over, but it also charges the battery. The wire brushes inside of the starter are designed to produce electrical current and send it to the battery as the engine runs.
How do you use a pull-start?
0:060:55How to use the pull start on a atv - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're just going to go ahead get a good firm position on our pedal here. And then just one nice pullMoreWe're just going to go ahead get a good firm position on our pedal here. And then just one nice pull. Right up that's how you start.
Why are lawn mowers pull-start?
Your lawn mower takes so many pulls to start because the fuel filter is filled with debris, the spark plugs aren't working, the battery is damaged, or there's not enough gas in the tank. A damaged engine can make the mower take more pulls to start because it won't combust the oxygen and fuel.
What is the thing you pull to start a lawn mower called?
Push, or walk-behind, mowers commonly feature a pulling mechanism that is designed to turn the crank shaft and start the lawn mower engine. Also known as a recoil start, the pulling mechanism consists of a few different parts that work together to allow a user to start the mower engine.
How do you pull-start?
0:162:05How To Pull Start an Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust like that instead of pulling and pulling and pulling and trying to guess when it'll start youMoreJust like that instead of pulling and pulling and pulling and trying to guess when it'll start you just pull it over the compression cycle and give it one good hard yank and they'll start right up.
How do you pull-start a truck?
0:000:56Pull Starting a Truck Engine by Hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll right the first thing you got to do is a jack up one of the rear. Wheels once the wheel is up inMoreAll right the first thing you got to do is a jack up one of the rear. Wheels once the wheel is up in the air you just take your toe strap that you should always have and wrap it around the tire.
Can you pull-start a diesel engine?
RAY: So theoretically, yes, you certainly can roll-start a diesel engine using fourth or fifth gear. But keep in mind that we do have a recent invention that makes this completely unnecessary in most cases, Bobby. It's called the ignition key.
How do you fix a pull-start on a go kart?
Fixing a go-kart pull start is easy, but you'll need to get a high-quality pull string or new recoil spring....1. Replace the Pull StringStep 1: Disconnect the Recoil Starter Housing From the Engine. ... Step 2: Replace the Old Pull String. ... Step 3: Reattach the Recoil Starter Housing.