- Place your clock on a level surface. Grandfather clocks rely on gravity to keep accurate time. ...
- Rotate the minute hand counterclockwise to avoid playing the melody. Most grandfather clocks play a melody and chime on the hour.
- Move the minute hand clockwise if the clock is a few minutes off. ...
- Set the day count and moon phase if the clock has them. ...
- Move the hour hand if the chimes are wrong. If you notice that the hour hand is showing one time but the number of chimes is indicating another, move ...
- Wind the clock weekly, or as often as necessary. You should wind your clock at least once a week to keep the time correct.
- Unlock and open the glass door of your Ridgeway grandfather clock to access its face and hands. ...
- Grasp the clock's minute hand gently between your thumb and forefinger.
- Rotate only the minute hand counterclockwise until both the hour and minute hands reflect the correct time.
How to setup an antique longcase grandfather clock?
Summary - Setting Up Your Antique Long Case Clock
- Make certain the clock is stable. ...
- Always wind up both weights of the clock and the chime side (the one on the left) a little more then the time side
- Never turn the hands backwards.
- Always let it strike each hour.
- To slow it down, lower the bob. ...
- Only correct the date between 4 and 8 o'clock.
How to move a grandfather clock the right way?
- Get at least three good friends to help you move your grandfather lock safely.
- Use a utility dolly to wheel your prized longcase clock out to the moving van. ...
- Use extreme caution when moving your grandfather clock up or down the stairs. ...
How do you adjust grandfather clock?
– Push the minute hand around the clock until the clock displays the actual time. How do you adjust a Howard Miller grandfather clock? Turn the adjustment nut on the pendulum disk to change the speed of timekeeping. Turn the adjustment nut to the left to slow the clock down. Turn the adjustment nut to the right to speed the clock up.
How to set an analog clock?
Method 2 Method 2 of 2: Setting an Analog Watch Download Article
- Change the battery. If your watch has stopped, you may need to change the battery. ...
- Find the crown on your watch. This is the small knob on the side of your watch. ...
- Pull out the crown. On some watches, the crown will pull out to multiple levels. ...
- Set the time. ...
- Push the crown in. ...
How do you turn on a Ridgeway Grandfather Clock?
3:545:34How To Setup Ridgeway Grandfather Clock - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply move the chime selector switch located at the 3 o'clock to the off or silent position slowlyMoreSimply move the chime selector switch located at the 3 o'clock to the off or silent position slowly move the minute-hand which is the longer one clockwise.
How do you start a Grandfather Clock?
1:273:20How to easily wind & set your vintage grandfather clock - YouTubeYouTubeStart of suggested clipEnd of suggested clipMoving it over and letting. It find its way back and forth. Now the movement of the pendulum. We'llMoreMoving it over and letting. It find its way back and forth. Now the movement of the pendulum. We'll start to get the clock ticking. It's on nice solid ground here.
How do I turn my Grandfather Clock back on?
Take the minute hand (the long one) and move it back (counter-clockwise) one hour by rotating the hand backwards. If the clock chimes while you are doing this, it will not harm anything. If you feel any resistance on the minute hand, wait a few hours and try again.
How do you start a pendulum clock?
Place the clock where it is to be used, on a stable, level surface. Open the front door and hang the pendulum on the hook (on many clocks the hook is behind the dial), give the pendulum a swing, and the clock will start ticking.
How do you wind a Ridgeway clock?
How to Wind a Pendulum ClockLocate the winding points on the clock face. ... Insert the key or crank into a winding point. ... Continue turning the key or crank until it won't turn any further. ... Wind the other one or two winding points the same way if your clock chimes on the hour or quarter-hour.
Why is my grandfather clock not working?
Ensure the clock hands are not touching each other. When the hands are touching it usually means they are stuck and your clock will not run. Look at the hour and minute hands closely. If they are touching the "time train" may be jammed which prevents the pendulum from swinging.
Why is my Grandfather Clock not striking?
What if my mechanical clocks will not chime or strike? Make sure that the strike on/off lever is not in the "strike off" position or halfway between positions. Make sure that the movement is not in the "night off" position. Make sure that all the packing material is removed from the movement area.
What are the three winding holes on a clock?
The middle hole will wind the spring that powers the timekeeping function of the clock. The right hole, as you're looking at the clock, powers the chimes of the clock. Finally, the left winding hole, as you're looking at the clock, powers the hourly strikes of the clock.
How often do you wind a Grandfather Clock?
Wind weekly, or as necessary. Almost all grandfather clocks are made to run for seven or eight days without winding, so winding them on the same day each week will ensure that it never stops. If your clock stops before its regular winding time, however, you may need to wind it more frequently.
Why grandfather clock pendulum stops?
If the pendulum is touching the chime rods toward the back or touching the weights toward the front, the pendulum will stop. This indicates a problem in leveling from front to rear. Leveling ~ Your clock will need to be level from front to back and side to side.
How do you set a pendulum on a grandfather clock?
The pendulum disk is moved up or down by turning the adjustment nut. To slow the Grandfather Clock down, move the pendulum disk down by turning the adjustment nut to the left. To speed the Grandfather Clock up, move the pendulum disk up by turning the adjustment nut to the right.
How do you set a pendulum on a grandfather clock?
The pendulum disk is moved up or down by turning the adjustment nut. To slow the Grandfather Clock down, move the pendulum disk down by turning the adjustment nut to the left. To speed the Grandfather Clock up, move the pendulum disk up by turning the adjustment nut to the right.
How often do you have to wind a grandfather clock?
Wind weekly, or as necessary. Almost all grandfather clocks are made to run for seven or eight days without winding, so winding them on the same day each week will ensure that it never stops. If your clock stops before its regular winding time, however, you may need to wind it more frequently.
Why does the pendulum stop on my grandfather clock?
Often a pendulum clock will stop when it has been moved, bumped or even a too aggressive push to restart a pendulum. It is not broken, only out of beat. This only takes a few minutes to readjust and all pendulum clock owners should learn how as this will happen eventually.
Why would a grandfather clock stop chiming?
If your clock has stopped chiming after 5 years, or has stopped chiming correctly, chances are the problem is a lack of, or improper, maintenance. Most manufacturers of clocks recommend 'oiling' a clock every year.
How to set the moon on a clock?
In order to set the moon follow these simple instructions: With your fingertips, apply slight pressure to the front of the moon dial and rotate the moon dial clockwise until the moon is directly below the #15 lunar day mark (each mark represents a lunar day) on the lunar arch (See figure 9). If the moon dial will not rotate, see the Trouble Shooting Section. Refer to an almanac or calendar and determine the date of the last full moon. Count the number of days past the last full moon. Rotate the moon dial clockwise 1 lunar day for every day past the full moon.
How does a clock run?
In order for your clock to run continuously, you must wind (raise the weights) the clock regularly, before the weights get to the bottom of the cabinet. NOTE: NOTALL CLOCKS ARE “EIGHT DAY CLOCKS”. Although there is usually enough chain or cable on the clock movement to allow weights to fall for eight days (this is where the term “eight day clock” originates), the length of time can be determined by the design or size of the cabinet. Some clocks will require winding more often. We generally use two different types of movements in our clocks - chain and cable. Please select the instruction that matches your clock.
How to tell if a pendulum is slow or fast?
The distance the pendulum disc hangs from the clock movement determines how fast or slow your clock runs. This distance can be changed by turning the nut which is located below the pendulum disc. Turn the nut to the right and the pendulum gets shorter and the clock runs faster. Turn the nut to the left and the pendulum gets longer and the clock runs slower.
How to use a chainsaw chain?
1. Grasp the free end of the chain. 2. Pull straight down on the chain. You will be tempted to pull the chain toward you.Avoid doing this since it will cause links of the chain to open and eventually break. Do not lift up on the weight while winding as this could cause the chain to come off of the sprocket. 3. Use a slow even motion when raising the weight. Do not jerk the chain or release the weight suddenly as this could break the chain. Raise each of the weights to the bottom of the dial frame.
How long does it take for a cable driven clock to work?
ALLOW YOUR CLOCK TO OPERATE AT LEAST 2 HOURS BEFORE MAKING ANY ADDITIONAL ADJUSTMENTS. If, at the end of two hours the clock strikes the incorrect number of times on the hour, see the adjustment for synchronization on Page 9. REMEMBER: On cable driven movements, do not remove the Styrofoam packing between the pulleys and cables until they become loose through normal operation, which typically occurs after eight (8) hours of run time. At that time they can easily be removed without damage to the cables.
How to make a dial silent?
A. On the dial, move the lever (located at the “3” position) to SILENT.
What to do if the hour strike and time do not correspond?
If the hour strike and the time do not correspond you will need to make this adjustment. Example: The clock shows 4:00 and it strikes three times. Follow these instructions for correcting. 1. IF YOUR CLOCK IS SET IN THE SILENT POSITION, MOVE IT TO CHIME.
How to set grandfather clock?
In order to set the correct time and pendulum beat of a grandfather clock, make sure that it is on level ground. Then, carefully adjust the hands until they show the right time and set the pendulum swinging. Make sure that the pendulum continues to swing freely and evenly and the hands show the correct time. If not, a small adjustment is usually all that is necessary for your clock to keep accurate time.
How long does it take for a grandfather clock to adjust?
Give your clock a few hours to self-adjust. If you recently set up your grandfather clock, it may need an hour or two for the mechanism to adjust. Check on your clock after about two hours to see if the issue has resolved.
How to stop a clock from touching?
If they are touching something, hold the hand of the clock with two fingers near the center. Use your other hand or a needle-nose plier to gently pull it away from whatever it is touching.
How to keep grandfather clock accurate?
1. Place your clock on a level surface. Grandfather clocks rely on gravity to keep accurate time. If your clock is on a surface that tilts it in one direction, this will throw off the timekeeping mechanisms. Try adjusting your carpet or bringing the clock away from the wall.
How to set the clock back to the time?
In order to set the time without playing the melody, move the minute hand counterclockwise. Winding the minute hand 1 full rotation counterclockwise will set the c lock back by 1 hour. Do not move the hour hand.
How to wind a clock?
1. Wind your clock and start the pendulum. In order to wind your clock, determine if your clock is crank-wound or chain-wound. Look at the face of your clock. If there are 1-3 small holes, these are winding points for a crank. Insert the crank and wind either clockwise or counterclockwise, whichever feels most smooth.
How to move the clock forward in a piano?
If your clock is only off by anywhere from a few minutes to an hour, it will be faster to move the minute hand in a clockwise direction. Wait at each quarter hour for the melody to finish playing before you continue to move the minute hand. Winding the minute hand 1 full rotation clockwise will set the clock forward by 1 hour.
How to tell if grandfather clock is winding?
1. Look for the winding points. If your grandfather clock is wound by a crank or a key, it should have one to three small holes on the clock face. Most commonly, these are located near the 3 (III), the 9 (IX), the center, or anywhere in the lower half of the clock face. If you do not see a hole, and your clock did not come with a crank or key, ...
How to wind a clock?
Use the crank or key to wind the first weight. Gently push the shaft of the crank or key into any one of the winding holes. It should be a snug fit, but do not force it in. Gently hold the clock face steady with one hand, and use the other to gently turn the crank .
How to make a clock with more than one weight?
If your clock has more than one weight, it should also have more than one winding point in the clock face. Move the crank or key to the remaining winding points, turning it in each one until every weight is nearly touching the wooden board above it.
How to make a clock with a pendulum?
It depends what type of clock you have. Almost all use a hook and eye system, however. Hold the pendulum and gently hook it into place. Make sure it's not loose by gently pulling down on it. Let go of the pendulum and start the clock.
How to tell if a clock is chain-wound?
1. Look for chains hanging next to the weights. Open the door protecting the long, hanging weights in the clock case (not the pendulum). Most clocks have one, two, or three weights, but there may be more on unusual models. If you see a hanging chain next to each weight, your clock is probably chain-wound.
How to slow down a clock?
Be gentle to avoid bending or breaking the clock hand, and stop and wait for the clock to strike or time before continuing to move the hand. A nut on the bottom of the pendulum can be tightened to slow the clock down, or loosened to speed it up. Adjust this if you find yourself adjusting the time every week or two.
What to do if you can't find a chain in a clock?
If you cannot find either a chain or a winding hole in the clock face, ask someone to help you look, or consult a professional clockmaker or clock repair shop.
What is a Ridgeway grandfather clock?
Its classic design continues to attract consumers and collectors today. A Ridgeway grandfather clock is a treasured family heirloom and a striking timepiece that adds an attractive aesthetic to any room.
Who owns the Ridgeway clock?
As of 2004, the Howard Miller Clock Company in Zeeland, Michigan has control of the Ridgeway grandfather clock production. Howard Miller, which also owns Kieninger, a German company that makes clock parts, changed the way the clock machinations were made during that time. The Ridgeway is the oldest grandfather clock that has been manufactured continuously in the United States.
What does the serial number on a Ridgeway clock mean?
The first two digits of the Ridgeway serial number represent the year it was manufactured. For example, if the serial number starts with 93, it was made in 1993. Conduct a Ridgeway or Howard Miller grandfather clock serial number search online if you are unsure about what the serial number means for your particular clock.
What clock does the winner of the Monster Energy Cup get?
It is so revered for its craftsmanship that the winner of the NASCAR Monster Energy Cup Series at Martinsville Speedway receives a Ridgeway grandfather clock.
When did Gravely Furniture sell to Pulaski?
In 1960, the company moved to only producing the classic timepieces. In 1985 , Gravely Furniture was sold to Pulaski Furniture Corporation. This is where things can get confusing for some collectors. Pulaski began referring to only the majestic clocks as Ridgeway grandfather clocks.
Where is the serial number on a clock?
The serial number may be located along the inside back panel of the clock . This can be difficult to access. You will have to get down on your knees and look deep into the clock's inner workings. Be careful not to upset the weights or other parts of the clock while you are attempting to locate the serial number.
When did Gravely Furniture start making clocks?
The famed clock maker actually began as a sofa maker. The Gravely Furniture Company opened its doors in 1926 with well-crafted bedroom, living room and dining room pieces as well as statuesque grandfather clocks. In 1960, the company moved to only producing the classic timepieces.
How to keep a clock from crooking on the wall?
If this fails or you don’t wish to have a clock case crooked on your wall, you may take off the pendulum and slightly move the pendulum leader from left to right or right to left until it almost or starts moving back and forth on its own. It should have the same feel from dead center to right and dead center to left. Rehang the pendulum and the clock should continue and you are done.
How to set the beat of a pendulum clock?
How to Set The Beat of the Pendulum Clock. TIP – Prevention: for wall clocks, always remove your pendulum before taking the clock off the wall. If the pendulum stays in the clock it may scratch the inside of the case as well as change the beat and then the clock may not work. Check The “Beat”: Listen to the tick-tock on ...
How to check if a clock is out of beat?
You work toward equal time between the TICK and the TOCK. The pendulum needs to swing exactly equal distances from dead center to the left, as from dead center to the right. If a clock is out of beat, the pendulum will swing for a few minutes, then stop even if the clock case is level.
How to stop the clock when the hands are touching?
If the hands are touching, this will stop the clock. Slightly bend the hands away from each other by holding the hand still toward the center and slightly pulling the hands away from each other.
Why does my pendulum stop dragging?
Is the Pendulum dragging? Look into the lower side window and watch the pendulum swing. If the pendulum is touching the chime rods toward the back or touching the weights toward the front, the pendulum will stop. This indicates a problem in leveling from front to rear.
