How do you start a Stihl ms170 chainsaw?
- of 15: Before starting your chain saw, the chain brake should be activated by pushing it forward (see picture).
- of 15: Always remove the bar cover before starting your chain saw.
- of 15: If your chain saw is fitted with a decompression valve, press it now.
Full Answer
How to start a Stihl?
May 08, 2020 · How do you start a Stihl ms170 chainsaw? Move the" Master" control switch to the cold start position. Pull the spark plug wire off of the spark plug and remove the spark plug from the cylinder head.
Why is my Stihl Chainsaw hard to start?
Mar 24, 2020 · Starting the STIHL MS 170 petrol chainsaw on the ground is just as easy as working with our entry-level model. In the video we give you a step-by-step guide ...
How to pull the starter cord on a Stihl Chainsaw?
How do you start a Stihl MS 180 chainsaw? To start Stihl’s chainsaw , start by moving the chain brake forward to activate it and removing the hood over the chain and bar. Then press the bottom valve several times, if your chainsaw has one, and set the main control to the cold start setting.
How to start a Stihl gas powered hedge trimmer?
Pull the starting rope five or six times to clear fuel out of the combustion chamber. Replace the air filter and spark plug, and connect the spark plug wire. Leave the choke open and pull the starting cord several times. The chain saw should start.
How do I start my Stihl ms170?
0:322:59STIHL MS 170 Starting Procedure - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst engage the throttle. Then I can push it down all the way down to choke and it stays there onceMoreFirst engage the throttle. Then I can push it down all the way down to choke and it stays there once I'm full choke you just have to pull it.
How do you start a Stihl 017 chainsaw?
2:340:26How to Start a Stihl Chain Saw - YouTubeYouTubeStart of suggested clipEnd of suggested clipGive the saw throttle trigger a quick squeeze to disengage the throttle lock and bring the saw toMoreGive the saw throttle trigger a quick squeeze to disengage the throttle lock and bring the saw to idle.
Is there a trick to starting a Stihl chainsaw?
2:264:06Chapter 9: Starting Your STIHL Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pull until you feel slight resistance. At this point give the Rope a sharp brisk pull and thenMoreAnd pull until you feel slight resistance. At this point give the Rope a sharp brisk pull and then guide the rope back slowly into the starter housing.
Why will my new Stihl chainsaw not start?
If the engine doesn't start on the first three or four pulls, the fuel and air mixture becomes fuel rich, and if you continue to pull the starter while the choke is closed, there is too much fuel to ignite and the engine floods. You can simply wait for the fuel to drain, but there is a faster way to clear the engine.
How do you start the easy start on a Stihl chainsaw?
0:053:07How to start your Stihl MS 250C Easy2Start Chainsaw. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis lever all the way down past. These three points and in order to do that you push down pull theMoreThis lever all the way down past. These three points and in order to do that you push down pull the trigger and push it all the way down to the choke position once it's starting to start.
How does Stihl easy start?
Compared with conventional starters, the STIHL Easy2Start™ not only requires less effort, but also allows the starter rope to be pulled approximately two-thirds slower. The even pull on the starter rope overcomes the engine's compression to minimize the strength and effort required to start.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn't work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Where is the choke on a Stihl chainsaw?
The choke position is the fourth setting on the master control lever. This setting is used to start the saw when its motor is cold. Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
How do you start a new chainsaw?
0:301:54Chainsaw Basics: How to Start a Gas Chainsaw - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to make sure that your toggle switch is in the on. Position your choke is pulled out andMoreYou want to make sure that your toggle switch is in the on. Position your choke is pulled out and you've pressed the purge valve four to five times to prime the engine.
What is the button on top of Stihl chainsaw?
The Decompression Release Button lowers engine compression temporarily to make it easier to pull the start rope during starting.Jun 9, 2008
How do you know if your chainsaw is flooded?
1:008:51Quickly Unflood A Chainsaw Using NO Tools - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo start your spark plug. Cannot fire and ignite pure fuel in there it has to be a mixture of airMoreTo start your spark plug. Cannot fire and ignite pure fuel in there it has to be a mixture of air and fuel for it to actually run too much fuel in there. That's what flooding means.