how do you take apart a lazy susan

How to Disassemble a Lazy Susan

Full Answer

How do you remove a lazy Susan cabinet?

Remove the mounting screws holding the bearing to the base material with the Phillips screwdriver. Pull the freed bearing from the base. And there you have it. Your cabinet is finally free. Tip #1. It may take some force to remove the old Lazy Susan from the cabinet.

How do you remove a lazy Susan bearing?

Unscrew with a screwdriver, preferably a Phillips. You also need to rotate the base. Then remove the mounting screws as well. Now, turn the Lazy Susan over so you can see the top plate of the bearing. Remove the mounting screws holding the bearing to the base material with the Phillips screwdriver.

How to set up a lazy Susan base?

So you need to set the lazy Susan base up on a firm surface at a comfortable working height. Remove the screws from the top piece of the lazy Susan. This may be tricky, but if you installed the lazy susan yourself, then it won’t be.

How do you fix a misaligned Lazy Susan?

Adjusting misaligned Lazy Susan units might seem intimidating, but the most common corrections you'll need to make can be done at home using standard tools. Fix rotation problems by adjusting the center shaft or bottom shelf position. Remedy misaligned doors by correcting the door position from inside the overall unit.

What is a lazy Susan?

How to expose the screws holding the bearing to the base material?

About this website

Is it easy to let go of a kitchen?

Letting go is not easy. Especially if your kitchen is old and with a lot of memories. But you have no choice. Out with the old, in with the new.

Does the lazy Susan cabinet organizer rotate well?

Lazy Susan Cabinet organizer. Like magic, the lazy susan became the hero of blind corners, until it did not. As you probably know already, the lazy susan in itself is full of problems. The first one is the design challenge. Also, after a while, it does not rotate well. The plain truth is no one wants it anymore.

How to fix lazy Susan?

Fix rotation problems by adjusting the center shaft or bottom shelf position. Remedy misaligned doors by correcting the door position from inside the overall unit.

How to replace plastic lazy Susan?

Commonly, the older units will show the plastic to be worn. Simply replace the plastic piece, and it should realign and close properly .

What happens if you don't tighten the screws on a lazy Susan?

If the screws for your Lazy Susan don't tighten, the fasteners or the attaching hardware may be stripped. This means that damage has been done to the part of the hardware intended to grip the fastener (like the grooves of a screw). Replace stripped hardware and try again. Thanks!

How to adjust pivot base on Susan?

Realign the pivot base when necessary. Open the door wide enough to expose the bottom bracket on either side of the Susan. Loosen this bracket by removing the fastening setscrew and star washer with a screwdriver. Now you can realign the pivot cam (metal arm) base so that it’s centered.

Why is my lazy Susan so stiff?

When a Lazy Susan becomes stiff and difficult to rotate, the problem is usually caused by either the center shaft or the position of its bottom shelf. Lightly spin the Susan and note where it locks up, has difficulty turning, or has poor clearance. If the center movable shelf begins to bind, it will prevent free rotation.

Where are the locking screws on lazy Susan shelves?

Most Lazy Susans should have two or more locking screws located at the center of each shelf. These screws hold the shelves to the center shaft. When all of the shelves are held together by the front decorative panel, you will need to adjust the entire shelf system.

How to adjust center shaft on a cabinet?

Now that the bolt is loose, you’ll be able to adjust the center shaft. Slide the metal adjusting sleeve the bolt was holding in place no more than 1 inch (2.5 cm) to provide better clearance between the center shaft and top of the cabinet.

What is a lazy Susan?

A lazy Susan uses a rotating bearing to allow one pieces of material to rotate on top of another. A lazy Susan displays more items than a standard fixed shelf and increases the storage capacity of corner-mounted cabinets. Since the lazy Susan bearing rests between the two pieces of material, access to the screws holding the bearing to the material is limited. Disassembling a lazy Susan requires a straightforward approach and a little searching.

How to expose the screws holding the bearing to the base material?

Turn the top plate of the bearing to expose the screws holding the bearing to the base material.