How to Take Apart a Moen Shower Valve
- Step 1. Shut off the main water supply to the house by turning the valve to the right. The water valve should be located...
- Step 2. Gently pop off the decorative cap on the faucet handle with a flat screwdriver and do it slowly to prevent...
- Step 3. Loosen the screws on the escutcheon plate behind the faucet handle with a flat head...
Full Answer
How to take apart a Moen showerhead?
How to Take Apart a Moen Showerhead. Step 1. Locate the main water valve inside your bathroom sink's cabinetry. Twist the valve clockwise until it is in the "off" position. This ... Step 2. Grip the pipe section of your Moen showerhead with a pair of tongue-and-groove pliers, which are commonly ...
Is it time to replace your Moen shower faucet?
If your Moen shower faucet begins to drip water and the faucet handle is difficult to turn, it may be time to replace it. First, you need to remove the old valve cartridge before you can install the new one. It just takes a few tools to take apart your Moen shower valve and it is possible to do this job on your own.
How do you disassemble a shower faucet?
Before disassembling any type of shower faucet, turn off the water supplies to the shower and open the faucet to release water pressure in the pipes. If you have to pull out the handle of your shower faucet to turn on the water, the faucet has a cartridge.
Where do you put the water valve on a shower faucet?
The water valve should be located near the shower in an adjacent room or in the basement of the home. Gently pop off the decorative cap on the faucet handle with a flat screwdriver and do it slowly to prevent damage. Set it in a safe location for later.
See more
How do you change a cartridge on a Moen shower valve?
1:213:14How to Remove & Install the 1222 Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the cartridge is in the on position the notch in the stem should be facing up remove theMoreMake sure the cartridge is in the on position the notch in the stem should be facing up remove the cartridge from the valve. You can also use the Moen cartridge removal tool to pull out the cartridge.
How do you fix a dripping single handle Moen shower faucet?
0:2810:07How to fix a leaking Moen Shower - YouTubeYouTubeStart of suggested clipEnd of suggested clipStep is you're going to verify that the water is in fact off by turning the handle. And this alsoMoreStep is you're going to verify that the water is in fact off by turning the handle. And this also will drain out any excess water that's inside the valve.
How do you disassemble a Moen cartridge?
2:077:32How to remove and replace a Moen shower cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe Knick cartridge comes with a plastic knot that I will slide over the cartridge. And then I willMoreThe Knick cartridge comes with a plastic knot that I will slide over the cartridge. And then I will take my pliers. And twist on the plastic nut to loosen up the cartridge.
How do you take apart a Moen shower handle?
0:001:37Remove Shower Handle - Moen Shower Handle - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor a mowing handle a 7 64 hex is a common size after removing the set screw i used a rubber malletMoreFor a mowing handle a 7 64 hex is a common size after removing the set screw i used a rubber mallet to help loosen the handle remove the handle.
What Moen shower valve do I have?
If not the series number can be usually be found on the underside of the faucet or on the decorative escutcheon ring that goes around it. The second way to identify your Moen valve cartridge is to remove the old one. You will do this by first shutting off the hot and cold water feed to your shower.
How do I know if my Moen cartridge is bad?
When Should You Change Your Shower CartridgeLeaking from the handle, tub spout or shower head when off.Difficult to open or close shower valve.Difficult to turn shower handle.Inability to get very hot or very cold water.
How do you remove a shower valve stem?
1:157:15How to Repair a Shower Valve Stem | Ask This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn these anytime you look at these handles you realize they have to be attached somehow to get atMoreOn these anytime you look at these handles you realize they have to be attached somehow to get at the screw you have to pry off the index from the end.
How do you remove a single handle shower cartridge?
2:456:30How to Replace a Delta Faucet Shower Cartridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning itMoreUse a strap wrench or a pair of channellock pliers to loosen the bonnet nut by turning it counterclockwise then remove the bonnet nut by hand.
How do you remove a Moen cartridge without the tool?
2:0114:48Removing a Stuck Moen Cartridge Without Proper Cartridge PullerYouTubeStart of suggested clipEnd of suggested clipYou know kind of wiggle it and pull over straight.MoreYou know kind of wiggle it and pull over straight.
How do you remove a Moen handle?
Some Moen faucets have handles that remove by loosening the screw in the back of the handle. To loosen this screw use a 3/32" hex wrench. After the handle has been removed unscrew the spout collar nut by turning counterclockwise then lift and rotate the spout.
How do I remove a Moen handle adapter?
4:4020:07Moen Std Handle Adapter and 1225 Assembly MASTER - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis metal bracket is called a handle. Adapter. You after removing the screw the handle adapter canMoreThis metal bracket is called a handle. Adapter. You after removing the screw the handle adapter can be removed by lifting it off of the faucet.
How do you replace a Moen 1225 shower valve?
0:082:23Moen 1225 Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen remove the faucet handle cap or insert button be careful not to scratch the finish. This willMoreThen remove the faucet handle cap or insert button be careful not to scratch the finish. This will expose a screw which must be removed before you can pull off the handle assembly.
How do I stop my shower from dripping?
How to fix a leaky shower headCheck for a worn seal. Your O-ring or rubber washer is the component that prevents water from leaking between your showerhead and hose. ... Reattach the shower head and turn on the water. ... Turn your attention to the valve.
How do you remove a Moen faucet handle without screws?
You can use an allen wrench (also called an allen key) to remove it. Once you've done that, you can typically just lift the faucet handle off. However, if it has a cartridge inside, you may need to unscrew a top piece as well to be able to remove the cartridge.
How do you fix a leaky single handle bathtub faucet?
0:172:38Repairing a Leaky Single Handle Tub/Shower Ball-Type FaucetYouTubeStart of suggested clipEnd of suggested clipTurn off the main water supply to your home. For an obstacle remove the index button by prying offMoreTurn off the main water supply to your home. For an obstacle remove the index button by prying off with the screwdriver. Then unscrew the handle screw. And remove the handle.
How do you fix a leaky Moen bathroom faucet?
0:021:36How To Fix a Dripping Moen Faucet (HowToLou.com) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you look at your new one there's a little tab right there that goes to that slot right there soMoreIf you look at your new one there's a little tab right there that goes to that slot right there so just line those two up and push it in put your brass ring back on tighten. It with pliers.
How does a Moen shower head work?
How the Cartridge Works. Moen showerhead cartridges have rocker switches, which have the ability to open and close your cold and hot water lines. These switches are capable of changing the water to different temperatures, which makes for a more comfortable shower.
Why is my Moen shower not working?
When a Moen showerhead is not working properly, it is usually due to it needing cleaning, stuck or damaged cartridges or failing O-rings (which are located around it). Before taking the showerhead apart, you first need to shut off the valve that controls the bathroom's water. This is probably located in the bathroom sink's cabinet.
What is a Moen showerhead?
Moen is a respected company that manufactures bathroom and sink fixtures, and Moen is known for its cart ridge-designed shower faucets. Rather than having hot-water and cold-water taps, Moen showerheads work with lever-style handles and cartridge valves. If your Moen showerhead starts leaking, or if it seems to be working poorly, ...
How to get O rings out of a cartridge?
To help ease out the cartridge, grip it with pliers. Move the cartridge carefully from side to side; this should loosen the O-ring from the metal stop tube. The cartridge is held in place with a retaining pin, and you can pull this out with needle-nose pliers. From here, you can see if the O-rings are damaged.
How to pull out O rings?
The cartridge is held in place with a retaining pin , and you can pull this out with needle-nose pliers. From here, you can see if the O-rings are damaged. If they are, you will need to purchase replacements.
Can you pull out a Moen shower head?
These cartridges can get stuck, and you may not be able to pull yours out without some additional work. The Moen cartridge puller (removal tool) can help get it out, but sometimes they are not effective, or the cartridge may break. In cases like this, the best solution may be to contact a licensed plumber to fix your Moen showerhead.
What happens if you pull out the handle of a shower faucet?
If you have to pull out the handle of your shower faucet to turn on the water, the faucet has a cartridge. If the faucet leaks or you can't control the temperature, you usually have to remove the cartridge and clean it or replace O-rings and gaskets. The procedure begins with turning off the water to the shower and opening ...
What are the different types of shower faucets?
Every manufacturer of shower faucets has its own idiosyncratic approach to design, but on the whole, shower faucets fall into one of three categories: cartridge, ball valve and compression. If your faucet has a single handle, you'll find either a cartridge or ball valve when you disassemble it.
Why is my faucet leaking?
Sometimes, the faucet is leaking because one of the valve seats is cracked. The valve seats are replaceable, and to remove one, you need a seat wrench, which looks a bit like a hex wrench. Insert the wrench into the valve housing and through the valve seat, and then turn the seat counterclockwise to unscrew it.
What is a Pfister shower faucet?
Other manufacturers, such as Price-Pfister (now known simply as Pfister) offer both cartridge-style and compression faucets. A general disassembly procedure works for most faucets, but if you're in doubt about the details of your shower faucet, look up the manual on the manufacturer's website.
How to avoid damaging finish on ball valve?
To avoid damaging the finish, wrap a rag around it first. Once you've removed this, the ball-valve assembly simply lifts out along with the adjustment ring and an O-ring. Inside, you'll find rubber gaskets around the hot and cold inlets, and there are springs underneath them.
Do Moen faucets have a cotter pin?
Moen faucets often have a cotter pin that must be removed with pliers. If you're disassembling a Delta faucet, you usually have to unscrew and remove an outer metal sleeve to expose a large retaining ring that you can unscrew with locking pliers.
Does a shower diverter have a valve?
The shower diverter, if it's built into the wall, usually has a valve somewhere between a cartridge valve and a compression valve. No matter which type of faucet valve you have, the process for disassembling it is essentially the same.
