Whirlpool Washer Disassembly Guide
- Remove the agitator by removing the cap off the top then removing the bolt, down in the agitator.
- Lay the washer down on its back. Note you may have to disconnect the hose in order to do so.
- Remove the three bolts that hold the gear-case on.
- Pull the entire gear-case and agitator shaft out.
- Remove the trust bearing off the agitator shaft.
Why is my Whirlpool washer not draining completely?
It’s also a great idea to check that the drain hose is positioned correctly. If the hose is too far or not far enough down inside the standpipe, it can cause improper draining. This in turn causes the Whirlpool washer to not drain the water completely.
How to take apart a GE topload washer?
Things You Will Need
- Unplug the electrical cord from the wall outlet. ...
- Slide a putty knife between the top of the washer and the front panel about 3 inches from the left corner. ...
- Unscrew the screws on the top of the front panel using a Phillips screwdriver. ...
- Remove the screws that hold on the back access panel using a nut driver. ...
How to take apart a front load washer?
- find the end covers (usually plastic)on each side of the control panel.
- with a small screwdriver, gently pry the bottom of the covers forward and up.
- under that cover you will notice a small screw that holds the panel to the top of the washer.
How to reset your Whirlpool washing machine?
The following steps should be used to reset your Whirlpool washing machine:
- Turn off the washer.
- Turn the mode dial to NORMAL.
- Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
How do you take apart a top load washer?
0:309:40GE Top-Load Washer Disassembly – Washing Machine Repair HelpYouTubeStart of suggested clipEnd of suggested clipNow insert a putty knife under the main top to release the two spring clips securing the front panelMoreNow insert a putty knife under the main top to release the two spring clips securing the front panel. Pull the front panel forward and lift up to remove remove the two screws securing the main.
How do you take the top off a Whirlpool top load washer?
7:4216:02Whirlpool Top-Load Washer Disassembly (Model WTW7120HW0)YouTubeStart of suggested clipEnd of suggested clipSupport the main top with the chain. You can now remove the wash plate tub cover and inner tub. UseMoreSupport the main top with the chain. You can now remove the wash plate tub cover and inner tub. Use the small flathead screwdriver to help detach the wash plate cap.
What are the most common problems on a Whirlpool washing machine?
Here are seven of the most common problems on a Whirlpool washing machine and potential fixes for them.Washer Making Unusual Noises. ... Washer Won't Start. ... Washer Lid Won't Lock. ... LD Error Code Appears. ... Washer Leaves Deposits on Dark Clothes. ... Washer Has a Burned Plastic Odor. ... Rust Spots Appear on Washer Lid.
How do you take apart a Whirlpool front load washer?
3:3010:55Whirlpool Front-Load Washer Disassembly, Repair ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panelMoreUse a t20 Torx bit to unthread the screws in the dispenser. Housing. Next cut the control panel housing mounting. Screws. You can now lift up the task to detach the housing.
How do you remove a washing machine cover?
Open the lid on the washing machine and place your hand between the drum and the top of the machine. Lift upward and toward you to remove the metal cabinet. If the cabinet does not lift easily, slide it toward the front of the machine, then lift. Be careful not to dent the casing as you take it away from the drum.
What would make a Whirlpool washer not spin?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
How do you fix a Whirlpool washer that won't spin?
14:1119:41Whirlpool Washer Won't Spin - How to Test and Fix - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd keeps falling out you'll need to purchase a new shift actuator of a slightly different model andMoreAnd keeps falling out you'll need to purchase a new shift actuator of a slightly different model and i'll have the part number in the description.
How do you fix a loose agitator on a Whirlpool washer?
2:094:12WASHING MACHINE AGITATOR LOOSE—EASY FIX - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'll wrap it running I wrap it on really tight. And this would just buy you some time this mayMoreI'll wrap it running I wrap it on really tight. And this would just buy you some time this may actually even work for a month or two.
How do you reset a Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.
Why is my HE washer not cleaning my clothes?
A common reason why your washing machines is not cleaning clothes properly is because the line leading from the detergent tray to the drum has become clogged up with washing up powder. This means that just a small amount of detergent actually reaches the drum – the rest of it becomes stuck behind the blockage.
Why is my Whirlpool washer not draining?
Drain Hose is Kinked or Clogged. A kinked or clogged drain hose is one of the most common reasons for a Whirlpool washer not draining. Kinks can occur if the washer moves or pushes the hose up against the wall. This twist in the hose restricts the flow of water, causing it to back up into the washer.
How do I reset my Whirlpool front load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How to remove the control panel on a washer?
1. Disconnect power from washer. 2. Remove the two screws (one on each side) that hold the control panel on. On some washers, you will see the screws from the front, some you will have to snap a cover off to see the screws and on some washers the screws will be on the back . 3.
Can you replace a Whirlpool washer clutch?
Above are Whirlpool washer disassembly instructions for disassembly down to the motor, which is all you need to know for most Whirlpool washer repair however sometimes you have to replace the gear-case or the clutch. To do so first remove the motor and pump as shown above, then follow these additional steps.
How to remove washer clips from washer?
There will be one clip located in the slots on each side in the area that is normally covered by the console. Use a flat head screwdriver to pry the ends of the clips out from the top of the cabinet. This will loosen the tension so that the other end slides down and out of the tab on the back panel.
How to open a washer cabinet?
Slide the console toward the front of the machine. When the tabs under the console have cleared the slots in the top of the washer cabinet, lift it up and roll it open on its hinges.
Can you disassemble a Whirlpool washer?
Never disassemble a washer while it's plugged in or with the water lines turned on. If you need to access the cabinet of your Whirlpool washer to do repairs, you'll have to remove the panel on the back. Although removing the back is fairly simple, you can't just remove the panel without some preparation, including removing ...
How long does it take to open a Whirlpool washing machine?
On a Whirlpool unit, the clips are located near the back and require you to lift the lid from the back toward the front. You can open the top of the washing machine in less than 15 minutes to access the interior workings of the appliance.
Where to find end caps on washing machine?
Locate the end caps of the washing machine on the back instrument panel, and pull the caps off by hand, being careful not to break the plastic clips.
