How to Wind a Bobbin on a Brother Sewing Machine
- Place your spool of thread on the spool pin.
- Run the thread to the thread guide on the left and wrap it around according to the picture on top of the machine.
- Now run the thread back to your bobbin winder.
How do I use my brother LS 30?
11:4122:08Brother LS30 Instructional Video (English) - YouTubeYouTubeStart of suggested clipEnd of suggested clipConnect the power supply plug into the jack of the machine and turn the main power switch. On setMoreConnect the power supply plug into the jack of the machine and turn the main power switch. On set the pattern selection dial to 1a pass the upper thread into the hole the presser foot align. The red
How do you thread the bottom bobbin on a brother?
0:303:16How to Thread and Properly Insert a Bobbin - Brother JX2517 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay you take your thread you put it through the tiny hole in the bottom and you hold it.MoreOkay you take your thread you put it through the tiny hole in the bottom and you hold it.
How do you thread a bobbin on a brother ls2350 sewing machine?
0:162:17Brother Video Tip: Winding and Threading Your Bobbin - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace your bobbin into the bobbin winder shaft. And slide the bobbin winder shaft to the right. NowMorePlace your bobbin into the bobbin winder shaft. And slide the bobbin winder shaft to the right. Now twist the bobbin clockwise by hand until the spring on the shaft clicks.
How do I fix the bobbin thread on my Brother sewing machine?
1:223:22Common Brother Sewing Machine Problems: Causes and RemediesYouTubeStart of suggested clipEnd of suggested clipThis is what you do turn the Machine off remove the presser foot unscrew both of these screws.MoreThis is what you do turn the Machine off remove the presser foot unscrew both of these screws. Remove the bobbin. And remove the needle plate. Check through here for loose threads.
How do you thread the bottom bobbin?
5:579:27How to wind a bobbin and thread the bottom of your sewing machineYouTubeStart of suggested clipEnd of suggested clipThe top to the left. So anti-clockwise you then drop it into the Machine. And at. If you imagineMoreThe top to the left. So anti-clockwise you then drop it into the Machine. And at. If you imagine this is looking like a clock between 6 and 7 o'clock you'll have just a really tiny little catch.
How do you load the bottom bobbin?
0:472:52How to Load a Bobbin | Sewing Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo now with the bobbin in the casing you're gonna go ahead and load it into your machine. You'llMoreSo now with the bobbin in the casing you're gonna go ahead and load it into your machine. You'll take this little lever and hold it out that'll keep your bobbin.
How do you thread a bobbin on a Brother LS 2125i sewing machine?
2:403:39Threading the Light Blue Brother LS-2125i - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to use our left hand and we're gonna hold the thread that's coming from the needle.MoreSo we're going to use our left hand and we're gonna hold the thread that's coming from the needle. Our right hand goes onto the handwheel thumb on top going. Towards us so the needle goes down.
How do you thread a bobbin on a Brother LS 1217?
0:182:18Brother LS-1217 Sewing Machine: Winding The Bobbin - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're going to place the bobbin on the bobbin winder. And then pull the slack. Back in then all we'MoreWe're going to place the bobbin on the bobbin winder. And then pull the slack. Back in then all we're going to do is push the bobbin winder in. And then we're going to start pushing our foot pedal.
How do you put a bobbin in a Brother LS 2125?
0:402:27How To Thread Bobbin on Brother LS 2125 Sewing Machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you just want to match the notch. That is on the bottom. Holding holding it in just like so andMoreSo you just want to match the notch. That is on the bottom. Holding holding it in just like so and then these two side pieces hold it together.
Why is my bobbin not threading?
- Make sure the bobbin is wound evenly and has been inserted into your machine properly. - Check for scratches on the bobbin case. - Make sure that the bobbin thread is pulled completely under the pretension, to assure that the bobbin is wound evenly. - Make sure you are using the correct bobbin in the machine.
What causes a sewing machine to not pick up the bobbin thread?
There could be several things that could cause the machine not to pick up the bobbin thread. The upper thread could be tangled. Remove the thread completely from the machine. The correct size spool cap should be used for the size of the thread spool.
Why is my sewing machine not catching the bottom thread?
First, make sure the bobbin-winding spindle (located on top of your machine) has been pushed back to the left for sewing. If it is not in the correct position, the needle will not go down and pick-up your bobbin thread.
How do you thread the bottom of a sewing machine?
1:042:36How To: Pick Up (Collect) Bobbin Thread (Sewing for Beginners)YouTubeStart of suggested clipEnd of suggested clipI tend to do in those cases is to grab a loop hair scissors your unpick er something like that whereMoreI tend to do in those cases is to grab a loop hair scissors your unpick er something like that where you can just hook underneath.
Why isn't my sewing machine grabbing the bobbin thread?
- Make sure the bobbin is wound evenly and has been inserted into your machine properly. - Check for scratches on the bobbin case. - Make sure that the bobbin thread is pulled completely under the pretension, to assure that the bobbin is wound evenly. - Make sure you are using the correct bobbin in the machine.
How do you thread the bobbin on a brother cs6000i?
0:384:42Brother CS 6000i 5 Threading & Winding a Bobbin - YouTubeYouTubeStart of suggested clipEnd of suggested clipClockwise. Around it and you need to make sure the thread actually gets underneath.MoreClockwise. Around it and you need to make sure the thread actually gets underneath.
How do you thread a bobbin on a Brother LS 2125i sewing machine?
2:403:39Threading the Light Blue Brother LS-2125i - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're going to use our left hand and we're gonna hold the thread that's coming from the needle.MoreSo we're going to use our left hand and we're gonna hold the thread that's coming from the needle. Our right hand goes onto the handwheel thumb on top going. Towards us so the needle goes down.
What is the bobbin on a Brother sewing machine?
Scissors. In order to sew on any sewing machine, it is necessary to have a threaded bobbin. The bobbin thread interlocks with the top thread and shows on the underside of material when you sew. The bobbin on a Brother sewing machine is threaded by placing an empty bobbin on top of the machine and winding it there .
How to wind a bobbin?
Holding the end of the thread, gently depress the foot pedal to make the bobbin begin winding. Stop when the spinning bobbin holds the thread on its own. Clip off the excess thread and depress the foot pedal again to spin the bobbin winder until the bobbin is full.
How to insert bobbin in shuttle race?
Place the filled bobbin in the bobbin case and guide the end of the thread through the slit on the side of the case and out through the top of the case. Holding the bobbin case by the latch, insert the case into the shuttle race, which is located on the lower front part of the machine. Click in place. (See Fig. 4)
How to change the needle on a sewing machine?
Step 1. On the side of the sewing machine is a wheel that moves the needle when turned by hand. In the center of this wheel is a clutch release switch that can move up and down. There is a small picture of a needle at one position and a bobbin opposite it. Push the switch up or down so that the switch is at the bobbin setting.
Which way to pass threads around bobbin?
Pass the thread counterclockwise (to the left) around the ‘bobbin winding thread guide’. It’s often a circle.
How to cut excess thread off bobbin?
Cut the excess thread off using the slit on the bobbin winder (circled below in red). You slide the thread into the slit and pull it to the right to cut.
How to wind thread into a bobbin?
Your bobbin normally has 1 (or more) holes in it. Insert your thread through the hole in the bobbin from the inside to the outside. It might be easier for you to take the bobbin off the machine to do this.
How to stop thread from getting tangled?
Make sure the thread unwinds to the front from the bottom. This stops the thread from becoming tangled around the spool pin, according to Brother.
What thread is used on a vertical spool pin?
Cotton thread on a vertical spool pin.
How many differences are there in bobbins?
There are about 6 differences in the process depending on whether you have a basic or computerized machine, a front-loading or top-loading bobbin system, and whether your thread spool stands up or lies down, etc. This post covers them all!
What is a bobbin?
A ‘bobbin’ is a small circular item that holds thread. You can get plastic or metal versions. Place your bobbin on the ‘bobbin winder shaft’. It’s the small silver pin at the top of your machine. My plastic bobbin on the ‘bobbin winder shaft’.
How to wind a Brother sewing machine?
To start winding the bobbin use the hand crank on the side of the sewing machine to raise the needle until it is as high as it can go. The bobbin on a brother sewing machine is threaded by placing an empty bobbin on top of the machine and winding it there. The filled bobbin is then removed and inserted into the bobbin case under the main sewing plate.
How to stop a bobbin machine?
Only use bobbins that were designed to be used with this machine. Turn the hand crank toward you to do this and once the needle gets as high as it can go you can stop turning the crank. Then stop the machine.
How to remove bobbin cover?
Unwind about 4 of thread from the full bobbin. Remove the bobbin cover by sliding it and lift toward you.
How to wind a bobbin?
While holding the end of the thread gently press the foot controller to wind the thread around the bobbin a few times .
What is the Best Thread for Brother Sewing Machine?
This question should be answered by first considering what you’re sewing. If you are doing a lot of top-stitching, then you might want to use a heavier thread. Thread weight is measured in tex, with 8 being the heaviest and 50 being the lightest.
Things to Consider When Threading Your Machine
It is always best to read the manual for your specific sewing machine before attempting thread.
Where can I find instructions for threading a Brother sewing machine?
You can find diagrammatic instructions for threading a Brother sewing machine in your manual, the quick-start guide, or on the body of your sewing machine. However, I always prefer real picture tutorials. So that’s why I’ll be showing you how to thread your Brother sewing machine using my Brother CS6000i as a model.
What class bobbins are used in Brother sewing machines?
Make sure to only use compatible Brother bobbins for your sewing machine. In the case of most Brother sewing machines, this will be Class 15, SA156 plastic bobbins.
How to wind a bobbin on a sewing machine?
Use low foot pressure or the slowest slider speed when pressing start/stop to wind the thread a few times. Then, press down harder or increase speed to fully wind the bobbin. For all sewing machines, now clip the excess thread and slide the bobbin winding pin back to the left.
How to trim thread in bobbin seat?
Pass the thread through the slit in the base of the bobbin seat to trim the excess thread.
How to start bobbin winding?
To begin the bobbin-winding process, first, pull the spool pin all the way up or out, and place your spool of thread on it. If your machine has a horizontal spindle, you may need to place the spool cap over it. My vertical spindle machine does not need a spool cap.
How to wind a Brother sewing machine without a bobbin?
For Brother sewing machines without fast bobbin-winding: Insert the end of the thread into one of the holes in the bobbin. Turn on the sewing machine and either press the start button (if your machine is computerized) or press the foot pedal down while holding the end of the thread. Use low foot pressure or the slowest slider speed when pressing start/stop to wind the thread a few times. Then, press down harder or increase speed to fully wind the bobbin.
How to tell if bobbin is spinning counterclockwise?
You should be able to see the directions on the base of your sewing machine for a diagram reference. If you were to pull your thread, the bobbin would spin counterclockwise.
How do you thread a bobbin on a Bother LS 2020?
Firstly, a bobbin is a wheel-like circular object around which the thread is spun. Its main job is to hold the thread that is used to form the stitches on the fabric. Now, to wind, a bobbin follows the steps given below.
How do you put the bobbin back in a Brother sewing machine?
The universal method mainly involves disengaging the needle first and then popping up the bobbin enclosure.
What is a computerized sewing machine?
A computerized or digital sewing machine with an automatic threader allows follows the same procedure for How to thread a brother sewing machine. The difference being the use of buttons in the digital ones. For instance, to pull up the needle, we press the up button on the machine while we rotate the dial on the manual machine. Digital machines help in making our lives simpler and a digital sewing machine serves its purpose too.
How to thread Brother sewing machine?
Step 1: Wind the bobbin. Step 2: Install the bobbin properly. The process of doing that has been discussed above. Step 3: Thread the top thread.
What is a sewing machine?
Sewing Machine. A sewing machine is a machine that is used to sew fabrics and materials, and uses a thread to do so. These days we have electric sewing machines and the most trusted brand, without a doubt, is Brother. The common issue everybody used to face back then and is still facing is how to thread a brother sewing machine.
What is the difference between a home sewing machine and a commercial sewing machine?
However, home sewing machines and commercial sewing machines have a lot of differences. The commercial ones are bigger, smoother, and faster to use , unlike the home sewing machines for obvious reasons.
When was the sewing machine invented?
It was built to reduce the amount of manual sewing work being done in the clothing companies. The first sewing machine was used in the early 1800s and since then, the productivity and efficiency of the machine have only gone upwards.
