7 Ways to Tighten a Bolt That Keeps Spinning
- Use a Longer Bolt. Here we are referring to the issue of the bolt not being long enough for the hole it’s being...
- Use a Wider Bolt. The issue could also be that the bolt you are using is not wide enough for the hole it is meant to...
- Get Unstripped Bolts or Nuts. A likely cause is of course that the bolt or the nut...
How do you use toggle bolts on a wall?
Push the toggle bolt (with the item attached) into the hole in the wall until you can feel or hear the wings spring open. Use one hand to pull the item and the bolt forward (toward you) until the pair of wings contact the back of the wall. Keep this pressure constant as you turn the bolt clockwise.
How do you fix a loose bolt on a wall?
Push the entire toggle nut into the large hole in the wall. Once inside, you should hear it open. Using a screwdriver or a power driver, tighten the bolt from the front. Important – The butterfly toggle should be resting on the drywall on the inside for the bolt to tighten. If not, the bolt will spin and will not tighten.
What happens when you tighten a toggle bolt?
As the bolt is tightened, it presses against the drywall. This causes the bolt to anchor in the drywall. The larger the area of the butterfly toggle in contact with the drywall, the stronger the anchor and the higher the weight rating. What size toggle bolts do I need?
How do you use a wing bolt to hang something?
Insert the bolt into the shank after first inserting it through whatever you're going to hang. The next step is a little tricky. Use your fingers or a screwdriver to hold the wings (which have spread out behind the drywall) against the back of the wall while you tighten the bolt with another screwdriver.
How tight do you tighten toggle bolts?
7:339:16How to Use Toggle Bolts - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you just push it through.MoreIf you just push it through.
How do you fix a loose toggle bolt?
2:528:05How To Fix A Pulled Out Or Damaged Drywall Anchor | Toggle BoltsYouTubeStart of suggested clipEnd of suggested clipYou can also from the back side take some needle nose pliers. And hold on to the plastic. Part andMoreYou can also from the back side take some needle nose pliers. And hold on to the plastic. Part and then use your phillips head and back that screw.
How do you secure a toggle bolt?
1:382:43How to Use Toggle Bolts to Hang Almost Anything - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm just going to use a electric screwdriver to screw the toggle screw. I have these wooden capsMoreI'm just going to use a electric screwdriver to screw the toggle screw. I have these wooden caps that you insert over the screws. You hide the screw.
How do you use a spring toggle bolt?
0:271:51Spring toggles - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd push it through the. Oil. Then in order to get this ring toggle to bite on the bike youMoreAnd push it through the. Oil. Then in order to get this ring toggle to bite on the bike you sometimes have to pull the item that you're fixing forwards a bit.
Why do my drywall anchors keep pulling out?
If you put even moderate outward force on one, however, it can easily pull right out of the wall. The easy repair is to replace it with a larger conical anchor, but that anchor will probably also pull out in time. A more effective solution is to replace it with a plastic screw-in anchor, a molly bolt or a toggle bolt.
How do I stop my anchor from spinning?
Push Them In The anchor can be pushed back with a screwdriver and a bit of force. You can also use a hammer to tap the end of a screwdriver or other similar metal object and force the anchor behind the edge.
How do you install a toggle bolt without a drill?
0:472:33How to Put an Anchor in Drywall Without a Drill - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext we would take our drywall anchor and place it right on top of our screwdriver. Then we're goingMoreNext we would take our drywall anchor and place it right on top of our screwdriver. Then we're going to take it. Put it into the hole. And just begin to tighten it in. There.
How does a toggle screw work?
A toggle bolt works by anchoring itself to the back of the drywall, so when you put outward force on the bolt, the entire sheet of drywall resists it, not just the crumbly core. The two types of toggle bolts are the wing style and the strap style, which features a solid support bar that makes it easier to install.
How much weight can toggle bolts hold?
Toggle bolts are the types of drywall anchors that can support up to 50 pounds, while steel hollow-wall anchors have a drywall anchors weight limit of up to 100 pounds.
How do you use a plastic toggle bolt?
0:000:53Plastic Toggle Anchors - YouTubeYouTubeStart of suggested clipEnd of suggested clipInsert the anchor into the hole. And tap it flush with a hammer insert the red key to pop the anchorMoreInsert the anchor into the hole. And tap it flush with a hammer insert the red key to pop the anchor open behind the wall. This is not necessary in thick or solid walls remove.
What are spring toggles?
Spring toggles are used to secure objects to surfaces such as plasterboard or hardboard. They are a heavy duty anchor suitable for overhead applications but can also be used to fix radiators or handle rails. They are fast and easy to install and the spring loaded wings come pre-assembled on the pan head screw.
How do you use toggle bolts on metal studs?
0:001:14How to Installing Metal Stud Bolts for a TV Wall Mount - YouTubeYouTubeStart of suggested clipEnd of suggested clipGoing up and down vertical represent the metal stud. After you drill your hole you're going to takeMoreGoing up and down vertical represent the metal stud. After you drill your hole you're going to take your toggle bolt straighten all the way out to where it's flat. Against the against the plastic.
How do you tighten a metal wall anchor?
3:066:48How to Fit Hollow Wall Anchors - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore you insert your anchor into the wall it's very important that you put your bracket. OrMoreBefore you insert your anchor into the wall it's very important that you put your bracket. Or whatever it is that you're fixing it to the wall. In between the bolt. And the anchor fixing itself.
Why is my screw not going into the anchor?
Try wedging two or more wooden toothpicks in the anchor, preferably toward the sides (glue probably won't help since it doesn't tend to stick to the soft plastic in anchors). Now when you drive the screw, the toothpicks should push outward, creating a tighter fit that may be enough to lock the screw into the anchor.
How do you fix a pulled wall anchor?
0:183:38HOW TO Fix Pulled-Out Drywall Anchors - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they ripped out these anchors now we've got these holes in the walls that we got to go ahead andMoreAnd they ripped out these anchors now we've got these holes in the walls that we got to go ahead and fix. So i'm going to show you how to fix it and put this towel hook back up there if you want to
How does a toggle bolt work?
A toggle bolt works by anchoring itself to the back of the drywall, so when you put outward force on the bolt, the entire sheet of drywall resists it, not just the crumbly core. The two types of toggle bolts are the wing style and the strap style, which features a solid support bar that makes it easier to install. Advertisement.
How much weight can a toggle bolt hold?
A 1/2-inch diameter toggle bolt can support 340 pounds in 3/8-inch drywall and up to 600 pounds in 3/4-inch ...
What is a strap toggle anchor?
Instead of wings, a strap toggle anchor has a spring-loaded bar, and it comes with a plastic frame. One popular brand, the Snaptoggle, gets its name from the method you use to install it as well as from the fact that it's a snap to install.
How to snap a bar on a wall?
Hold the bar perpendicular to the frame and slide it through the hole. The bar will automatically snap into position perpendicular to the wall. Slide the cap along the frame until it is flush against the wall, and then snap off the part of the frame that extends past the wall.
Rather watch than read? Check out this 8-minute video
DISCLAIMER: This blog contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission
The Problem With Some Drywall Anchors
Recently, I was trying to hang an 18” towel rod in a bathroom. I was able to secure part of it on a stud, which is always the preference when hanging something on drywall. But because it was 18” – I knew it would hit a wall cavity for the left-hand side of the towel rod. So I needed to use some form of anchor.
The Solution: Toggle Bolts!
For my situation, I already made some holes in the walls, so let’s use those holes and insert a toggle bolt .
1. Remove loose anchors
Remove the loose anchors. They should come out by unscrewing the screw from the anchor.
2. Pass toggle bolts through the brackets & thread them
I used 18” x 3” toggle bolts that I passed through the bracket and then threaded on the spring nut on the end of each of the two toggle bolts. You’ll start to thread it through (but don’t go too far down the hole).
3. Compress
Then you’ll compress both of the spring nuts and pass them both into the wall cavity. You can do this one at a time if it’s easier for you. You’ll pass them in and wait for the click – and the click will mean that the spring nut flared out behind the drywall. Then, you’ll do the bottom one.
4. Tighten them up
Once they’re in the wall cavity, you can do a test to make sure that they are spread out and they don’t pull back through. If that’s the case, then start to tighten them up with a compact nut driver until they’re snug against the wall.
What size toggle bolt do I need?
The first thing to consider is the thickness of your wall. ⅜” and ½” are the most common drywall thicknesses.
What is toggle bolt?
Toggle bolts are heavy-duty anchors perfect for installing anything in the drywall where you cannot find and screw into studs. They consist of two parts –. The bolt – the length and diameter of these decide their strength. The toggle – The butterfly-shaped nut whose size also determines the strength.
Why does a butterfly toggle bolt anchor in drywall?
As the bolt is tightened, it presses against the drywall. This causes the bolt to anchor in the drywall. The larger the area of the butterfly toggle in contact with the drywall, the stronger the anchor and higher the weight rating.
Why is a 4" bolt needed?
The 4″ long bolt is because it needs to pass through the 1½” thick board and then through the drywall. ¼” is the diameter of the bolt. Since these shelves will be holding dishes etc., in my kitchen, I went with the highest weight rating I could find.
Can a butterfly toggle bolt spin?
Important – The butterfly toggle should be resting on the drywall on the inside for the bolt to tighten. If not, the bolt will spin and will not tighten. This is a very common problem people encounter with toggle bolts. It has a straightforward fix.
What to do if a bolt and nut are spinning together?
If the bolt and nut are spinning together, it’s time to crack the bad nut. Get a nut splitter from your local hardware store, or you can easily buy one online, and break the nut. Be careful not to apply so much pressure that you damage your work surface.
How to avoid spinning bolts?
Before drilling, blow, or use a tiny piece of cloth to clean the hole out completely. Make sure you use the right drill bit and drill straight. Holding the drill at an angle will secure the bolt in place.
Why isn't my bolt spinning?
However, your bolt isn’t spinning because you have managed to over tighten it. This too can be harmful to whatever project you are doing. When you over tighten or over-torque a bolt you could strip the bolt or even snap the screw heads.
Why does a bolt spin in place?
The bolt may spin in place due to a few different reasons: A hole with specks of dust can prevent the bolt from staying in place. It acts as a lubricant. Another reason may be that you have the wrong-sized bolt. Both over and under-sized bolts are going to keep spinning.
Can you overtighten a bolt?
Are Your Bolts Stripped? Let us just start off by pointing out that it is possible to overtighten your bolt. Overtightening will cause its strings to be bent out of shape and the bolt will never tighten. If your bolt is spinning, you will need to check if your bolt is stripped or your nut.
Can you tighten a spinning bolt?
Although it might seem like the spinning bolt won’t tighten, it’s not impossible. Sometimes, the problem is quite simple and just tightening the bolt further or drilling a bit deeper will get the job done. Other times, you’ll have to remove/ break the bolt (and maybe even the nut) and start from scratch.
What do you use to tighten a bolt?
Wrenches are used to tighten and loosen fasteners, mainly nuts and bolts. Wrenches are generally made from a chrome-plated steel alloy. The material makes wrenches both durable and simple to clean.
How tight do you tighten a bolt?
In general, you should make the bolt tight enough so that the items it is holding together stay together, but not so tight that you damage the bolt’s threads. You should tighten bolts properly so that the bolt performs properly.
How do you tighten a bolt without a socket wrench?
Zip-tie. These wonderful little toolbox accessories aren’t just used to tidy up cables and attach hubcaps, they can also be used in place of a spanner. Place the zip-tie around the nut as tightly as possible and using the tail of the zip-tie pull in the direction necessary to loosen or tighten the nut.
What tool do you use to tighten nuts?
wrench, also called spanner, tool, usually operated by hand, for tightening bolts and nuts.
How do you make a metal screw tighter?
Tap the top of the screw hole with a hammer to flatten the outside edges. Inspect the threads on the screw to ensure they are intact. Thread the screw into the hole and tighten it with the appropriate screwdriver.
How do you stop a bolt from moving?
Nylon or metal inserts inside a nut (sometimes called a “lock nut”) can add extra friction to prevent loosening. A related idea is to fit a spring inside the nut, which firmly grasps the bolt threads and is designed to move in the opposite direction of the nut if vibration or other forces cause it to unwind.
How do you know if a bolt is tight enough?
Direct tension indicators are washers that have small protrusions on them. When the bolt is tightened, the gap between the unturned element and the washer decreases. The size of the gap is then measured and when it reaches the desired size, the bolt is pronounced tightened.