Step-by-Step Instructions
- Raise your needle completely.
- Lower your presser foot if necessary.
- Press the needle threader lever.
- Wrap your thread around the elbow-shaped bracket.
- Pass the thread into the cage where the thread-catch hook is located.
- Release the lever.
- Pull the loop through the eye of the needle.
How to thread a Bernina?
Easy Instructions for Threading a Bernina Serger
- Preparation. Number each thread path, starting at the left of your Bernina serger. ...
- Upper Looper. Grasp the No. ...
- Lower Looper. Repeat steps 1 and 2 in section 2, using the No. ...
- Right Thread. Repeat steps 1 and 2 of section 2, substituting the second thread. ...
- Left Needle. Repeat steps 1 to 3 of section 4 with the first thread on the Bernina serger. ...
What is a Bernina stitch regulator?
The BERNINA Stitch Regulator, more often known as BSR, is an attachment that works with certain BERNINA sewing machines to create stitches that are the same length as you free motion stitch. This attachment regulates the size of your stitches for you as opposed to traditional method where you, the sewist, regulate the stitches yourself (as is common with thread painting and free motion quilting).
How to thread a needlepoint needle?
Steps To Thread Needle For Cross Stitch
- Select Cross Stitching Needle. You have to choose the beginning cross-stitch thread needle for your cross-stitching project. ...
- Choose Embroidery Thread. Then you have to choose the perfect embroidery thread you require, a single strand of thread falls off the needle for cross-stitching.
- Cut Required Size Of Thread. ...
- Un-Strand Embroidery Thread. ...
How to thread a needle with a needle threader?
- Step 1: Twist thread around the top part of the needle, near the eye.
- Step 2: Pinch the end of the thread and pull it out to create a loop.
- Step 5: Double the thread up, then make the ends neat and tie together with a single loop. Pull it tight. ...
How does the Bernina threader work?
The manual needle threader enables threading of the needle eye. The thread is pushed through the needle eye by a small metal wire. Then use the small hook to pull the thread completely through the needle eye.
How do you use a Bernina 770 needle threader?
1:132:07Bernina 770 6 Needle Threader - YouTubeYouTubeStart of suggested clipEnd of suggested clipThrough the needle let me just put your thread underneath the foot. And you're ready to go so let'sMoreThrough the needle let me just put your thread underneath the foot. And you're ready to go so let's do that one more time so halfway down all the way down push.
How do you use a bernette needle threader?
0:521:40Bernette London 5 7 Needle Threader - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen put the thread in there lift up and let it pull it out of your hand. So if you hold on tooMoreThen put the thread in there lift up and let it pull it out of your hand. So if you hold on too tight over here it can't pull the loop through and well.
Why is my automatic needle threader not working?
- Needle might be installed incorrectly or damaged or bent. - The wrong size needle is being used. - The type of the thread being used is prohibitied for the automatic needle threader. - The hook of the needle threader might be damaged.
How do you thread a Bernina b740?
2:103:36How To Thread Your Bernina 770QE? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe scoop underneath that little plastic arm and then this fully goes all the way down and you'llMoreWe scoop underneath that little plastic arm and then this fully goes all the way down and you'll feel it positively click and there's a little wire that goes through the eye of the needle.
How do you fix a needle threader on a Bernina 880?
0:362:10Fixing Bernina needle threader - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull down on this on the threader. And you're gonna try and just get it to pop all the way back up.MorePull down on this on the threader. And you're gonna try and just get it to pop all the way back up. And you're going to be moving. It. And if you pull all the way down.
How do you use bernette b35?
0:101:02How to use Bernette b35 Needle Theader - YouTubeYouTubeStart of suggested clipEnd of suggested clipHold the thread out the back pull your needle threader forward slowly let go and you'll get a littleMoreHold the thread out the back pull your needle threader forward slowly let go and you'll get a little loop at the back of the needle. Pull that loop. And your needle is threaded you.
How do you use bernette sew and go 1?
bernette sew&go 1, 3 + 5: threading and preparing to sewButton Sew-On Foot. With this presser foot not only buttons of different sizes can be sewn on but also rings or hooks. ... Bobbins. The bernette bobbins always maintain the thread tension consistent. ... Darning Plate. ... Zipper Foot. ... Buttonhole Foot with Slide. ... Zigzag Foot.
How does an automatic threader work?
Automatic threader – Many sewing machines sold today come with an automatic threader function. This is essentially a lever that will guide the thread through the eye of your sewing needle for you so that you don't have to do it yourself.
How do you change a Bernina needle threader?
2:166:04Replace the Needle Threader on your Bernina Jeff shows how easy it is ...YouTubeStart of suggested clipEnd of suggested clipAnd your new needle threader has to line up with that pin right in that little rounded slot it goesMoreAnd your new needle threader has to line up with that pin right in that little rounded slot it goes on with the metal side pointing to the right. And angles about 45 degrees to the back.
Why won't my thread stay in my needle?
One of the most common issues leading to a needle that keeps unthreading is a sewing machine with the wrong thread tension in place. Thread tension at the top that's either too high or too low can result in this issue.
How do I thread my Bernina sewing machine?
2:123:59How to thread a BERNINA sewing machine - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure the thread is properly hooked in the thread take-up lever guide the thread through theMoreMake sure the thread is properly hooked in the thread take-up lever guide the thread through the guides at the bottom of the take-up lever cover. And at the needle bar. Then let go of the thread.
How do you change a Bernina needle threader?
2:166:04Replace the Needle Threader on your Bernina Jeff shows how easy it is ...YouTubeStart of suggested clipEnd of suggested clipAnd your new needle threader has to line up with that pin right in that little rounded slot it goesMoreAnd your new needle threader has to line up with that pin right in that little rounded slot it goes on with the metal side pointing to the right. And angles about 45 degrees to the back.
How do you thread a bobbin on a Bernina sewing machine?
2:047:07Bernina 480 5 Threading & Winding a Bobbin - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo put the silver side down and then take the thread around it the direction that it shows you to goMoreSo put the silver side down and then take the thread around it the direction that it shows you to go which is clockwise. Oh four five six times and then you're going to come underneath.
What are the steps in threading the lower part?
How to Thread a Sewing MachineWind a bobbin. The bobbin is the lower spool of thread for your machine. ... Load your wound bobbin. ... Place the spool. ... Thread through the thread guide. ... Pull the thread through the U-shaped guide. ... Wrap the thread around the thread take-up lever. ... Thread the needle. ... Catch the thread.
How does a needle threader work?
Needle threaders take the imprecision out of threading by working in reverse . Instead of guiding the thread straight through, the threader allows you to anchor it in place, then pull the needle around it.
How to use a wire threader loop?
Guide the end of the thread through the threader loop. The wire threader loop will give you a much larger target to aim at. Once you’ve got the thread inside, pull the loose end to continue feeding it through. [4]
How to thread a needle without squinting?
If you’re over it with the frustration of attempting to thread a needle the old-fashioned way, try using a needle threader tool. Just insert the wire loop through the eye of the needle, then slip your thread through the larger threader hole and double it over. When you slide the needle off the loop, it will catch the thread effortlessly, and you can knot it and get right to stitching without a lot of unnecessary squinting and poking.
Why do you need a needle threader?
A needle threader is helpful if your thread is on the thicker side, if it keeps unraveling, or you have poor vision or hand/eye coordination.
How to get a needle out of a wire loop?
Be careful not to let the needle slip back off the thread. Pull the loose end of the thread free. Give the thread a gentle tug to work it out of the wire loop the same way it went in. Work the loose end out with your fingers if needed. The thread should now be running straight through the eye of the needle.
How to use single thread for sewing?
Knot the thread around the eye of the needle. If you’re content with using single thread, simply tie off the loose end. You can then begin sewing as usual. That’s all there is to it!
How to get thread out of a needle?
Pull the loose end of the thread free. Give the thread a gentle tug to work it out of the wire loop the same way it went in. Work the loose end out with your fingers if needed. The thread should now be running straight through the eye of the needle.
How to avoid rethreading a Bernina serger?
To avoid completely rethreading your Bernina serger, loosen the tension, trim the thread directly above the thread path, tie on the new thread and gently pull it through the entire thread channel. Return the tensions to their correct setting.
How to thread a serger?
Clip the right needle thread into the flat needle guide directly above the right serger needle. Grasp the end with the tweezers and slip the thread into the eye of the right needle. Pull the thread toward the back of the machine.
How to thread a looper eye?
Locate the sideways V-shaped and grooved lower looper eye that points toward the right of the machine. Grasp the thread end with the tweezers and place it in the hole. Pull the thread over the already-threaded upper looper eye, under the presser foot and toward the back of the Bernina serger.
What is the first thread on a Bernina serger?
The first thread leads to the left needle and the second to the right needle. The third thread path goes to the upper looper, while the fourth thread corresponds with the lower looper. If there is a fifth thread, it is the thread for the coverstitch function on compatible machines. You will thread your Bernina serger in ...
How to thread a serger with a guide rod?
Pull the thread downward from the guide rod. Pass it through the metal guide clip at the back of the serger and directly in front of the thread holder that you are currently working with. Grasp the thread just below this clip and pull the thread downward and into the thread tension knob.
What is a serger for sewing?
Thread snips or sharp scissors. Sewing tweezers. A serger is a valuable tool for the modern seamstress. Most sewing aficionados find that they no longer want to sew without one once they are used to the many benefits of this handy machine. It can, however, be intimidating to thread your Bernina serger. Luckily, Bernina makes this process as easy as ...
Where to pull thread from a looper?
Pull several inches of the thread away from the back of the upper looper eye and under the presser foot.
Threading the upper thread correctly
I already touched on this topic in my April 2020 blog post, which you can find here: How to Begin Sewing Without “Eating Up Your Materials”
Thread types, thread stands, thread nets and more
I have often been asked whether it makes a difference which thread stand you use and in what direction the thread is inserted. The newer BERNINA models have two thread stands, one horizontal and one vertical.
