Pour clean water into the mixing bucket and then add the full bag of Dunlop Concrete Resurfacer. Mix with a mixing paddle and heavy-duty drill. Pour the mix onto an area of concrete.
Full Answer
Can I use Dunlop concrete resurfacer on vertical surfaces?
Dunlop Concrete Resurfacer can also be used on vertical surfaces such as walls or staircases.
How to resurface a concrete floor?
Instructions 1 Repair the Surface. Concrete resurfacers should be viewed as cosmetic finishes, not repair products. When serious damage is widespread, resurfacing will mask the problems for only a short time. 2 Clean and Prepare the Surface. It is critical that the concrete surface is cleaned of all loose debris. ... 3 Mix the Resurfacer
What is the best product to resurface a concrete slab?
If you are fully resurfacing a concrete slab, make sure to use a resurfacer designed for the purpose, such as Flo-Coat Concrete Resurfacer from Sakrete, Concrete Resurfacer from Quickrete, or Re-Cap Resurfacer, also from Quickrete. This type of product will be clearly labeled as "concrete resurfacer" rather...
How do you use Dunlop multipurpose primer?
Apply a coat of Dunlop Multipurpose Primer and allow to dry. Pour clean water into the mixing bucket and then add the full bag of Dunlop Concrete Resurfacer. Mix with a mixing paddle and heavy-duty drill. Pour the mix onto an area of concrete. Use a flat trowel, squeegee or broom it over the surface.
How do you apply concrete resurfacer?
3:054:28How to Resurface Concrete - YouTubeYouTubeStart of suggested clipEnd of suggested clipWorking back and forth evenly spread the resurfacer onto the slab. After. About five minutes a non-MoreWorking back and forth evenly spread the resurfacer onto the slab. After. About five minutes a non-slip finish can be applied using a concrete broom.
How thick should concrete resurfacer be?
1 Unlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab. Concrete resurfacer is a very strong product, rated for compressive strength of about 4,500 psi.
Do you need to seal concrete resurfacer?
Sealing is the final step to protect new and resurfaced concrete. It is also essential for ongoing maintenance. Resurfacing can be completed within two days while sealing can take just a few hours.
How many square feet does a 40 lb bag of concrete resurfacer cover?
One 40 lb (18.1 kg) bag of Concrete Resurfacer will cover approximately 17 ft2 (1.6 m2) of surface at a thickness of 1/4 in (6.4 mm) or approximately 90 ft2 (8.4 m2) per bag when applied at the minimum thickness with a broom or squeegee.
Will concrete resurfacer crack?
Preparation is very important when resurfacing concrete. If you use on top of a damaged slab then the resurfacer won't last long before it starts to crack.
Does concrete resurfacer really work?
That begs the question, “does concrete resurfacing last?” The short answer is, “yes.” If there are no issues with the underlying foundation the resurfacing agent pours onto, then the new material will last. It bonds to the foundation, creates a seal, and leaves you with a brand-new concrete driveway.
What is the best product to resurface concrete?
Our Top PicksBest For Interiors. Quikrete Fast-Setting Self-Leveling Floor Resurfacer. ... Best for Exteriors. Rapid Set High Strength, 15 Min Set, Featheredge. ... Best For Cracks. KILZ Over Armor Textured Wood/Concrete Coating. ... Best For Flooring. Ardex Feather Finish Grey Self-Drying Cement. ... Best For Small Jobs. ... Best Premixed.
Can you put a thin layer of concrete over concrete?
How thin can you pour concrete over concrete? Your new layer needs to be at least 2 inches thick. If it's any thinner than that, it'll easily crack under pressure and won't adequately bond to your surface.
When can I seal concrete resurfacer?
While it can be tempting to apply driveway concrete sealer right after it is poured, this is never recommended. There is excess moisture in the concrete that needs to evaporate during the curing process. The total curing process normally takes about a month before the concrete is solid and ready to be sealed.
Is quikrete concrete resurfacer self leveling?
QUIKRETE® Self-Leveling Floor Resurfacer (No. 1249-50) is a self-finishing interior floor topping and underlayment specially formulated to produce smooth surfaces ready for the installation of ceramic tile, resilient flooring or other finishes. No troweling required.
How long does concrete overlay last?
Concrete overlays typically last 10-15 years but can last up to 25+ years if well-applied and maintained. The overlay material quality, the amount of prep work done to the concrete, and the amount of regular maintenance can impact the lifespan of a concrete overlay.
How long does it take concrete resurfacing to dry?
Freshly placed concrete will require not less than 14 days but up to 28 days curing period before acceptance of decorative concrete resurfacing method.
How thin can you pour concrete over existing concrete?
about 2 to 2 ½ inchesHow Thin Can You Pour Concrete Over Existing Concrete? The thinnest that is usually used when pouring concrete, in general, is about 2 to 2 ½ inches. That also applies to this pouring new concrete over old concrete. Any thinner than 2 inches would be too thin.
Is quikrete concrete resurfacer self-leveling?
QUIKRETE® Self-Leveling Floor Resurfacer (No. 1249-50) is a self-finishing interior floor topping and underlayment specially formulated to produce smooth surfaces ready for the installation of ceramic tile, resilient flooring or other finishes. No troweling required.
What is the best product to resurface concrete?
Our Top PicksBest For Interiors. Quikrete Fast-Setting Self-Leveling Floor Resurfacer. ... Best for Exteriors. Rapid Set High Strength, 15 Min Set, Featheredge. ... Best For Cracks. KILZ Over Armor Textured Wood/Concrete Coating. ... Best For Flooring. Ardex Feather Finish Grey Self-Drying Cement. ... Best For Small Jobs. ... Best Premixed.
Can you add a thin layer of concrete?
Yes, you can put new concrete over old concrete providing there are no issues such as significant cracks of frost heaves with your existing concrete. A new layer of concrete should be about two inches to ensure an even, strong coverage.
What Is Concrete Resurfacer?
Well, for one thing, concrete resurfacer is a lot more expensive than plain concrete. In my area, a 60-pound bag of concrete mix costs $2, while a...
How Much Resurfacer Should I Buy?
It's hard to estimate the amount of resurfacer you will need, as much of the estimate depends on the final depth of the product. The manufacturers...
What If The Concrete Is damaged?
Concrete resurfacer will make the slab look a lot better, but it won't fix any underlying problems. Minor cracks can be patched. Oil, grease and pa...
What's The Best Weather For Resurfacing?
Concrete resurfacer should not be applied in cold weather. Make sure that the current temperature is at least 50°, and that the temperature will st...
How to apply Dunlop resurfacer?from dunlopdiy.com
Pour clean water into the mixing bucket and then add the full bag of Dunlop Concrete Resurfacer. Mix with a mixing paddle and heavy-duty drill. Pour the mix onto an area of concrete. Use a flat trowel, squeegee or broom it over the surface. Spread in a thin as a layer as possible while getting full coverage. Apply a light broom-finish to achieve the desired texture. Work in areas small enough to permit finishing without walking on the freshly installed areas.
What is Dunlop resurfacer used for?from dunlopdiy.com
Dunlop Concrete Resurfacer can also be used on vertical surfaces such as walls or staircases.
What is resurfacing mortar?from dunlopdiy.com
A concrete resurfacing mortar modified with high-performance polymers to provide exceptional bond strength. It can be used over the surface of exisiting concrete to produce a new wear layer as well as to fill in small surface defects such as spalls and gouges. Resurfacing concrete has never been so easy to refresh old concrete surfaces, especially driveways.
How to remove contaminants from concrete?from dunlopdiy.com
To remove contaminants use mechnical methods like sweeping, vacuuming high-pressure power washing and if necessary, grinding. Patch small holes, gouges ...
How thick is 9m 2?from dunlopdiy.com
9m 2 at 0.8mm thickness or 2.4m 2 at 3mm thickness per 10kg
Can you put pavers on sand?from ozbargain.com.au
If your pavers are on sand then this is not good as your pavers may wobble as you walk on them and cracks will form in the pebble finish. If however your pavers are on a concrete base then you can give it a go.
What Is Concrete Resurfacer?
Concrete resurfacer is a special cementitious product that blends ordinary Portland cement, fine sands, polymer modifiers, and other additives aimed at providing adhesion. 1 Unlike other cement products, it is designed to be applied in very thin coats (no more than 1/2 inch thick), and its additives provide good adhesion to an existing slab.
What is a resurfacer?
Resurfacers are self-leveling, meaning that they don't need to be worked extensively to create a level surface.
How to keep concrete from sticking to concrete?
Instead, cover the joints with duct tape to prevent the resurfa cer from sticking to them. Concrete resurfacer should not be applied in cold weather. Make sure that the current temperature is at least 50 degrees Fahrenheit, and that the temperature will stay above 40 degrees for at least the next 24 hours.
How many square feet does a 40 lb bag of concrete cover?
Concrete resurfacer comes as a dry mix in 40-pound bags or 50-pound pails. A 40-pound bag typically covers 15 to 90 square feet, and you usually apply two or sometimes three coats.
How much does it cost to resurface a 40 lb pail?
At $25 to $55 per 40-pound bag, or up to $70 for a 50-pound pail, resurfacing is not a cheap project, but it is less expensive (and much quicker) than tearing up an old slab and pouring a new one.
Can you demolish a concrete driveway?
If you have a concrete garage floor, driveway, sidewalk, or patio that is starting to show its age, you are left with two options: You can demolish and remove the old surface, prepare the base, and pour a new slab; or you can use a resurfacing process to restore the slab to its youthful appearance.
Can you resurface only part of a larger slab?
If you plan to resurface only part of a larger slab, be aware that it is hard to match colors. New concrete looks new, and old concrete looks old. If you really want to make the surface look new again, it's best to plan on resurfacing all of it. Most jobs require a second, and sometimes a third coat of resurfacer.
How to make a resurfacer with a drill?
Mix 1 part water with 7 parts resurfacer using a drill and paddle attachment. Pour the resurfacer powder into a 5 US gal (19 L) bucket, then add the water. Use a paddle attachment on a corded drill to mix the resurfacer. Keep mixing the resurfacer until it has a thick consistency like cookie dough.
What is resurfacing concrete?
Resurfacing means pouring a thin layer of concrete resurfacer over the top of your existing slabs to hide cracks and make it look brand new. Besides being more cost-effective than replacing the slab, you can resurface your concrete in a single day.
How to mix resurfacer with water?
Mix 5 1⁄2 c (1,300 ml) of cool water with 20 lb (9.1 kg) of resurfacer. Pour the resurfacer mix and the water into a 5 US gal (19 L) bucket. Use the corded drill with a paddle attachment to blend the resurfacer together. This time, blend the resurfacer until it has the consistency of pancake batter.
How many square feet does a bag of concrete resurfacer cover?
A bag of concrete resurfacer covers about 90 square feet (8.4 m 2 ).
How much water to mix with resurfacer?
The amount of resurfacer you need depends on how many cracks and holes you need to fill. Start by mixing 1 cup (240 ml) of water with 3 1⁄2 pounds (1.6 kg) of resurfacer mix.
How do I clean a concrete slab?
Use a power washer to remove dirt and loose concrete. Plug the power washer in, connect it to a water source, and turn on the machine using the switch. Hold the end of the power washer 3–4 inches (7.6–10.2 cm) from the surface of the concrete and pull the trigger to shoot out water. Use back and forth strokes to clean all of the concrete completely. Focus on areas where concrete is loose or deteriorating.#N#Look for a power washer with a fan tip that reaches 3500 PSI to clean your concrete slabs.#N#If you don’t have access to a power washer, you can get an attachment for your garden hose.#N#Cleaning your concrete makes the resurfacer adhere better.
What to wear when using a resurfacer?
Always wear rubber or nitrile gloves before touching the resurfacer. That way, it won’t dry on your skin.
What is a Quikrete concrete resurfacer?
QUIKRETE® Concrete Resurfacer is a special blend of Portland cement, sand, polymer modifiers and other additives designed to provide a shrinkage compensated repair material for making thin repairs to sound concrete which is in need of surface renewal. QUIKRETE® Concrete Resurfacer provides a beautiful, durable, wear resistant surface designed to withstand heavy foot and vehicle traffic. QUIKRETE® Concrete Resurfacer provides an economical alternative to removing and replacing existing old, spalled concrete.
How big is a section off of a concrete resurfacer?
Section off the work into areas no larger than about 144 sq. ft. (13.4 M2). Control joints and expansion joints can usually be used to define work areas. It is essential that control joints and expansion joints are maintained. Use weather stripping or duct tape to prevent QUIKRETE® Concrete Resurfacer from spilling into joints. Mask areas that are not to be coated with QUIKRETE® Concrete Resurfacer.
How long does it take for a Quikrete concrete resurfacer to work?
QUIKRETE® Concrete Resurfacer has a working time of about 20 minutes at 73°F (23°C). In hotter weather, working time will be reduced.
How much water to use for a concrete resurfacer?
Level spalled areas and pits with QUIKRETE® Concrete Resurfacer in trowelable consistency. Use approximately one part water to 7 parts QUIKRETE® Concrete Resurfacer. Allow the repairs to harden before resurfacing the entire area.
How long does it take for a sandpaper to cure?
Wait 6 hours before allowing foot traffic and 24 hours for automobile traffic. With cool temperatures allow longer curing time prior to use. Protect from rain for at least 6 hours, longer in cool or damp weather. Do not cover unless immediate rain protection is necessary. No sealer is required.
Can you use a pressure washer to clean concrete?
Old concrete must be rigorously cleaned to ensure proper adhesion of QUIKRETE® Concrete Resurfacer to the old surface. A high strength pressure washer must also be used to completely clean the existing concrete.
Can you use a broom to resurface concrete?
QUIKRETE® Concrete Resurfacer can be brush or broom finished for a professional look.
What is a Quikrete concrete resurfacer?from quikrete.com
QUIKRETE® Concrete Resurfacer is a special blend of Portland cement, sand, polymer modifiers and other additives designed to provide a shrinkage compensated repair material for making thin repairs to sound concrete which is in need of surface renewal. QUIKRETE® Concrete Resurfacer provides a beautiful, durable, wear resistant surface designed to withstand heavy foot and vehicle traffic. QUIKRETE® Concrete Resurfacer provides an economical alternative to removing and replacing existing old, spalled concrete.
How big is a section off of a concrete resurfacer?from quikrete.com
Section off the work into areas no larger than about 144 sq. ft. (13.4 M2). Control joints and expansion joints can usually be used to define work areas. It is essential that control joints and expansion joints are maintained. Use weather stripping or duct tape to prevent QUIKRETE® Concrete Resurfacer from spilling into joints. Mask areas that are not to be coated with QUIKRETE® Concrete Resurfacer.
How long does it take for a Quikrete concrete resurfacer to work?from quikrete.com
QUIKRETE® Concrete Resurfacer has a working time of about 20 minutes at 73°F (23°C). In hotter weather, working time will be reduced.
How much water to use for a concrete resurfacer?from quikrete.com
Level spalled areas and pits with QUIKRETE® Concrete Resurfacer in trowelable consistency. Use approximately one part water to 7 parts QUIKRETE® Concrete Resurfacer. Allow the repairs to harden before resurfacing the entire area.
How long does it take for a sandpaper to cure?from quikrete.com
Wait 6 hours before allowing foot traffic and 24 hours for automobile traffic. With cool temperatures allow longer curing time prior to use. Protect from rain for at least 6 hours, longer in cool or damp weather. Do not cover unless immediate rain protection is necessary. No sealer is required.
What is the best way to prewash a surface?from quikrete.com
Pre-wash the surface with a high-strength pressure washer.
Can you use a broom to resurface concrete?from quikrete.com
QUIKRETE® Concrete Resurfacer can be brush or broom finished for a professional look.
How to protect expansion joints when applying resurfacer?
It is important that expansion joints be protected when resurfacer is applied. Mask off these control joints with duct tape or weather stripping to prevent the resurfacer from filling them in. Resurfacer needs to be applied to a moist surface so the concrete won't draw moisture out of the resurfacer as it cures.
What is concrete resurfacing?
Concrete resurfacing products are intended only for covering the surface of concrete and will serve to repair only the most superficial cracks and pits. For more substantial repairs, such as wide cracks or those that have slight vertical shifts, you will need to first repair the areas using a product that is specifically designed for patching, such as Sakrete's Top 'n Bond, and then follow up with a complete resurfacing treatment.
How long does it take to dry concrete edger?
At the edges of the slab, you can create clean, professional-looking edges with a concrete edger, but only if you get to them within the first 10 to 15 minutes of application. Where a second coat is necessary, let the surface dry for two to three hours, then apply a second coat following the same procedure.
What is the best way to clean concrete?
It is critical that the concrete surface is cleaned of all loose debris. A strong spray from a garden hose and long-handled scrub brush may suffice, but a good pressure washing will provide better cleaning.
Can you use resurfacing to repair a crack?
Concrete resurfacers should be viewed as cosmetic finishes, not repair products. When serious damage is widespread, resurfacing will mask the problems for only a short time. But if you have only minor cracks or pits in your surface, resurfacing can be effective, provided you first repair the damage with a product specifically formulated for patching.
Can you resurface concrete?
Resurfacers will not correct deep cracking or heaving, but they can cover over routine flaking of a concrete surface or small pits due to spalling. A concrete slab that has been damaged by road salts, for example, can be renewed quite easily with a coating of resurfacer.
Can a resurfacer be slippery?
That's often what you want in a garage. However, the smooth finish can be slippery when wet, which makes it less desirable on a driveway, sidewalk, or patio surface.
What is DUNLOP grout?
DUNLOP GENERAL PURPOSE CONSTRUCTION GROUT is an economical, high-strength construction grout that can be mixed to a non-s lump or pourable…
What is silane modified adhesive?
A high performance and flexible silane modified adhesive and sealant for sealing and repairing joints and cracks.
