The removal of a gas line is a relatively simple process if you follow these steps:
- Shut off the gas supply.
- Disconnect or cut and remove the gas line.
- Use Teflon tape on threads, wrapping them clockwise if they are outside threads and counterclockwise if they are the threads of a plug that will screw into a pipe.
- Cap or plug the gas line and do a leak test.
- Physically, if needed, remove the old gas line that has been cut.
What to do if your old gas appliance is connected to a steel pipe?
How much water to use to test gas leak?
What to do if fittings don't match?
What size flare fittings are used for soft copper?
How to fix a leaky threaded pipe?
How to reduce 3/4 inch female pipe thread?
Can you use soft copper tubing to connect appliances?
See 4 more
About this website
How do you unclip a gas line?
1:422:43DIY: Removing a Push Lock Fuel Line Fitting - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically want to do is you can see there is a cutout on the one side here to snap it over top ofMoreBasically want to do is you can see there is a cutout on the one side here to snap it over top of the fuel line there. So once you snap it over top here you want to push this inside.
How do you use the Ford fuel line disconnect tool?
0:392:50How to Remove THOSE PESKY Ford Fuel Lines - ALL MODELS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipDifficult. It's going to take quite a bit of wiggling. Quite a bit of finagling. But eventually.MoreDifficult. It's going to take quite a bit of wiggling. Quite a bit of finagling. But eventually. Once you push down in the correct way the line will come apart.
How do I remove a quick disconnect fuel line?
0:134:21How to Disconnect Common Fuel Line Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipWith the push type connector. There are a couple different versions as you can see on this connectorMoreWith the push type connector. There are a couple different versions as you can see on this connector. There is a push here. And location the push on the other side.
How do I use OEM fuel line disconnect tool?
0:070:49OEMTOOLS 27131 Fuel Line Disconnect Set - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool position the tool against the fuel line and apply firm pressure the tool will snap into placeMoreTool position the tool against the fuel line and apply firm pressure the tool will snap into place over the fuel line. Slide.
How do I use the OEM master disconnect tool set?
0:070:53OEMTOOLS 27318 Master Disconnect Set - YouTubeYouTubeStart of suggested clipEnd of suggested clipAttach it to the line and snap it into place. Slide the disconnect tool into the fitting. This willMoreAttach it to the line and snap it into place. Slide the disconnect tool into the fitting. This will depress the latching tabs on the inside of the fuel line hole to separate.
What size is Ford fuel line disconnect tool?
5/16" sizeAir Conditioning / Fuel Line Disconnect Tool Set The 5/16" size fits on push lock connectors found on Ford radiators and transmission lines. Easy to use in confined spaces.
How do you use disconnect pliers?
0:302:31Quick Release Pliers from Lawson Products - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore using quick-release pliers remove all pressure from the lines lawson's quick-release pliersMoreBefore using quick-release pliers remove all pressure from the lines lawson's quick-release pliers are a great choice for messy fuel filters. They control fuel spillage. And help restrict gas flow.
How do I use the AC Quick Disconnect Tool?
3:164:32How to Remove A/C LINE on car. AC LINE DISCONNECT TOOL - YouTubeYouTubeStart of suggested clipEnd of suggested clipClick. Okay like that now holding this one you need to pull the line it's super busy with the tool.MoreClick. Okay like that now holding this one you need to pull the line it's super busy with the tool. Okay. And you can see this came out like that so no problem at all. Next.
What will happen if I directly connect my stove to a gas pipe ... - Quora
Answer (1 of 11): I am gas fitter. I teach gas fitting. Swapping out a gas appliance is something I would not recommend for a homeowner to do. It seems simple enough, break a friction fitting or a MBI fitting, put it back together and Bob is your uncle. I agree with the previous answers but nee...
Running and Connecting a Gas Line for Your Dryer
Connecting a gas line for your dryer is a simple task that can easily be carried out on your own. However, unless necessary precautions are taken, the job can prove to be quite costly (much more than hiring a professional) due to harmful effects of gas leakage.
What to do if your old gas appliance is connected to a steel pipe?
If your old appliance is connected with a steel gas pipe and you're installing a new appliance, buy a gas appliance connecting kit.
How much water to use to test gas leak?
Turn the gas back on and swab each joint with a solution of 2 tsp. dishwashing liquid to 1 cup water or with a commercially prepared leak testing solution.
What to do if fittings don't match?
If the fittings don't match, one solution is to replace the valve with one that has a flare fitting on one side and a 1/2-inch female pipe thread on the other side.
What size flare fittings are used for soft copper?
Common sizes of flare fittings are 3/8 inch, 1/2 inch, and 5/8 inch.
How to fix a leaky threaded pipe?
Fix leaky threaded connections by reapplying pipe joint compound or gas-rated Teflon tape and reassembling the fitting.
How to reduce 3/4 inch female pipe thread?
If necessary, use a bushing to reduce the existing 3/4-inch female pipe thread to 1/2 inch. Use a 90-degree elbow at the stove to avoid kinking the gas tubing when you push the stove against the wall. Before you replace an old valve, find and turn off the main gas valve to the house.
Can you use soft copper tubing to connect appliances?
A leak-proof joint is formed by the perfect fit between the flared end of the tube and the cone-shaped fitting. If the soft copper tubing isn't kinked or damaged, you can reuse it to connect your new appliance.
What is a fuel line disconnect tool?
Using a fuel line disconnect tool helps you disconnect the fuel line from the connector without causing damage. The tools put the right amount of pressure on the connection to disconnect with minimal effort on your part. Many fuel lines only disconnect using the specialty tool.
Why do you need to wear safety goggles when disconnecting fuel line?
Be sure to wear safety goggles to protect your eyes from the damaging buildup, grease, grime and dirt that is beneath your vehicle. Getting those things in your eyes not only makes it hard to see to work on your car, but they can cause further damage.
Can you disconnect fuel lines?
Many fuel lines only disconnect using the specialty tool. If you attempt to disconnect it using other methods, you may cause more damage to the system. The tool is rather inexpensive and costs much less than replacing fuel lines that were not damaged.
Average Cost of Gas Line Removal
Most homeowners hire a plumber to remove a gas line at a cost averaging $115 plus the cost of a permit cost if one is required. The cost is the same to cut and cap or plug the line, since the job goes pretty quickly. This is because simple jobs take less than an hour and cost the plumber’s minimum first-hour service fee.
Overview of Gas Line Removal
Removing a gas line is done one of two main ways. The easiest technique to remove a gas line is simply cutting the line, if necessary for space, capping it and leaving where it is. This is less expensive than physically removing the gas line pipe back to where it is connected to the main gas line.
Retail Costs for Gas Line Removal Tools and Supplies
This is a pretty basic job requiring few tools and supplies. Here are their costs.
Permits, Inspection, Related Costs and Installation Time
Removing or capping a gas line is a relatively quick and simple process for a licensed plumber. A licensed plumber responding to a question on Angie’s List calls it a “ 5-15 minute job ,” to cut and cap or plug a line, and so prices it at $90-$150, the minimum plumbing fee. Home Advisor is similar, pricing the service fee at $75 to $150.
DIY or Hire a Pro?
The removal of a gas line is a relatively simple process if you follow these steps:
What to do if your old gas appliance is connected to a steel pipe?
If your old appliance is connected with a steel gas pipe and you're installing a new appliance, buy a gas appliance connecting kit.
How much water to use to test gas leak?
Turn the gas back on and swab each joint with a solution of 2 tsp. dishwashing liquid to 1 cup water or with a commercially prepared leak testing solution.
What to do if fittings don't match?
If the fittings don't match, one solution is to replace the valve with one that has a flare fitting on one side and a 1/2-inch female pipe thread on the other side.
What size flare fittings are used for soft copper?
Common sizes of flare fittings are 3/8 inch, 1/2 inch, and 5/8 inch.
How to fix a leaky threaded pipe?
Fix leaky threaded connections by reapplying pipe joint compound or gas-rated Teflon tape and reassembling the fitting.
How to reduce 3/4 inch female pipe thread?
If necessary, use a bushing to reduce the existing 3/4-inch female pipe thread to 1/2 inch. Use a 90-degree elbow at the stove to avoid kinking the gas tubing when you push the stove against the wall. Before you replace an old valve, find and turn off the main gas valve to the house.
Can you use soft copper tubing to connect appliances?
A leak-proof joint is formed by the perfect fit between the flared end of the tube and the cone-shaped fitting. If the soft copper tubing isn't kinked or damaged, you can reuse it to connect your new appliance.