This tool is extremely easy to use. Just put your index finger under the band, put the the pivot point of the tool (which is directly under your finger) squarely on the center of the belt span, and *SLOWLY* press down. Release pressure immediately when the tool clicks. Lift the tool off and read the gauge.
How do I tension a belt?
Timing Belt - Tensioning
- Numerical Method (Force/Deflection) By measuring the deflection of the timing belt with a known force the required tension can be applied.
- Sonic Tension Meter. The sonic tension meter provides the most accurate tension measuring available. ...
- ContiTech - Mechanical Power Transmission Drive Design Calculator. ...
How to adjust a belt?
- Define if your belt is tighter or slack. ...
- Remove the right bearing to the exterior to make the head roller advance in a position that will tighten the belt.
- Put the left one in to move the head roller in a position that will slacken the belt.
- Make an adjustment, and then look at the belt. ...
- Reiterate the process till the belt looks centered to you.
How to measure your belt?
Method 2 Method 2 of 3: Measuring an Existing Belt
- Find a belt that fits. Take a belt that fits well – either one that you already have or go to a clothing store and try on belts until ...
- Spread the belt out flat. Put the belt on a flat surface like a table or on the floor. ...
- Measure the belt. ...
- Use the measurement that you found to order a belt. ...
- Use an existing pair of pants. ...
How to tension a treadmill belt?
To set the belt tracking:
- Turn on your treadmill and set the belt speed at 3 mph.
- If the belt is too close to the left side, turn the left-side bolt only a 1/4 turn to the right (clockwise) and wait a few minutes for the belt ...
- If the belt is too close to the right side, turn the left-side bolt counter-clockwise.
What gauge to use for belt tension?
What to do if your belt tension drops?
Do micro V belts need tension?
How do you use a gate belt tension tester?
0:001:13Gates Carbon Drive U Measuring Proper Belt Tension - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're gonna be using pounds today place the rubber strap over your index finger. And place theMoreWe're gonna be using pounds today place the rubber strap over your index finger. And place the cricket over the top of the belt. Press down until the tool clicks. Check the reading in pounds.
How tight should Gates belt drive be?
Much like a normal chain, there isn't one correct answer. So long as the belt stays in place and does not slip, there is a wide range of acceptable tension. With too little tension, the belt will skip; too much tension creates noise and is harder on bearings.
How do you use a Gates sonic tension meter?
Here's how it works: First, enter belt mass constant, belt width and span length into meter using built-in keypad. Next, hold meter sensor to belt span, then lightly strum belt to make it vibrate. Press “measure” button to obtain reading and the meter quickly converts vibrations into belt tension.
How do you use a digital belt tension meter?
1:282:53Sonic Tension Meter 507C - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're ready to measure the tension in the belt. First you're going to want to create a vibration inMoreYou're ready to measure the tension in the belt. First you're going to want to create a vibration in the belts. Then you hit the measure button on the meter. And bring the microphone up to the belt.
How long does a Gates belt drive last?
You can expect a regularly cleaned belt drivetrain to last upwards of 30,000km/19,000mi.
Is a Gates belt drive worth it?
The claimed advantages of the Gates Belt Drive compared to a traditional chain drive are lower maintenance and less mess (no lube is required), quieter and smoother (no metal to metal contact), lighter weight, and better durability. Gates also claims that the system provides twice the lifespan of a chain-driven system.
How do you check alternator belt tension?
Checking the belt tension Use a ruler to find the mid-point on the belt's longest run between pulleys. Use a ruler to find the midway point on the belt's longest run between pulleys. Hold the belt between finger and thumb at this point and move it from side to side. See how much it deflects at the centre of the run.
What is belt mass constant?
*Units of mass constant M for synchronous belts is g/(m)(mm) or g/10 cm2 along the belt pitch line . Constant M for V-belts represents the weight in grams of a 1 meter length of belting with a correction factor applied to compensate for internal bending resistance .
How does a tension meter work?
A tension meter is a device used to measure tension in wires, cables, textiles, Mechanical belts and more. Meters commonly use a 3 roller system where the material travels through the rollers causing deflection in the center roller that is connected to an analog indicator or load cell on digital models.
How do you break in Gates Redline belt?
1:332:44How To: Properly Install and Break in CVT Belts - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd let the belt completely cool for half an hour repeat. This process once more now you're ready toMoreAnd let the belt completely cool for half an hour repeat. This process once more now you're ready to start shredding the terrain with your new belt. Now this is the fun. Part.
How do you break in a drive belt?
0:081:01Break in your CVT belt like a pro - Flexin' or Wreckn' - Can-AmYouTubeStart of suggested clipEnd of suggested clipApplying. Light throttle not exceeding 4000 rpms you want to do this for about 10 minutes now onceMoreApplying. Light throttle not exceeding 4000 rpms you want to do this for about 10 minutes now once you've done that we'll switch over to high range make a couple high range passes easy acceleration.
How do you break in a new belt?
To break in a belt, use low gear (if available) while varying speeds and avoiding wide open throttle for 5 to 10 miles. If no low gear is available, vary at moderate speeds while avoiding wide open throttle for 50 miles. Breaking in a belt is about more than a set number of miles and avoiding high engine RPM.
Are gates G Force belts directional?
Although G-Force belts are not directionally biased, it is recommended to install them with the label lettering facing toward the user to keep belt reinstallation consistent.
How do you correctly tension belts?
If the belt feels solid when whacking it with a karate chop, the drive is correctly tensioned. " "With your thumb, press the belt until it deflects...
How do you set the drive belt tension?
Adjust the belt by loosening the belt adjustment bolt. Step 2: Tighten the drive belt. Slowly tighten the adjustment bolt to attain the appropriate...
How does a belt tension gauge work?
Apply a force to the belt at the center of the span with the tension gauge perpendicular to the span. Deflect the belt until the bottom of the big...
How much tension should a power steering belt have?
Check the belt tension by pressing inward on the belt with your hands. To be correctly tensioned, the belt should have no more than a 1/2 inch of s...
How do you check belt tension by hand?
At this stage, move the belt from side to side by holding it between your finger and thumb. Take a look at how much it deflects in the midst of the...
How do you check the tightness of a belt?
Twist the belt and measure the twist margin to check the tension. If the belt is properly tightened, tighten the screw in place to reinforce the ha...
Which way do you turn a belt tensioner?
With the appropriate sized socket and ratchet, rotate the pulley on the belt tensioner counterclockwise to release the strain on the belt. Remove t...
What gauge to use for belt tension?
Always use a belt tension gauge that indicates static tension, such as the Gates Krikit® Tension Gauge, to determine proper tension from the Installation Chart. Tension ranges below are for drives requiring single belts. If multiple belts are needed for a drive, divide tension by number of belts to give per belt tension to be measured.
What to do if your belt tension drops?
If belt tension drops below Suggested Tension range, retighten belt to Installation Tension. This will allow the belt to seat-in and run at Suggested Tension after it has operated under normal driving conditions.
Do micro V belts need tension?
Many Micro-V belts are automatically tensioned by a spring-loaded automatic tensioner, which does not require tension to be set. The tension ranges below are used for applications requiring manual tensioning. For drives with manual take-up on locked-center drives, position the belt and set tension to the prescribed Installation Tension.
What gauge to use for belt tension?
Always use a belt tension gauge that indicates static tension, such as the Gates Krikit® Tension Gauge, (Part No. 91107 for Standard, Part No. 91132 for Micro-V) to determine proper tension from the Installation Chart. Tension ranges above are for drives requiring single belts. If multiple belts are needed for a drive, divide tension by number of belts to give per belt tension to be measured.
How to check belt tension?
If multiple belts are needed for a drive, divide tension by number of belts to give per belt tension to be measured. Step 2: Run belt for five minutes. Step 3: If belt tension drops below Suggested Tension range, retighten belt to Installation Tension.
Customers who viewed this item also viewed
ARES 15033 - Belt Tension Gauge - Use After Belt Replacement, Adjustment or Wheel Service for Accurate Motorcycle Belt Tension Setting - Universal Design - 10 Lb Specification - Compatible with Harley
Product Description
Gates Krikit gauges provide a simple and quick way to measure belt tension on V-belts to ensure long belt life and optimal belt drive performance. This easy-to-use gauge is designed for tensioning all automotive V-belts up to, and including, 7⁄8 in. top widths.
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
How accurate are Krikit II gauges?
These Krikit II gauges are very accurate and quite handy to have. I get a lot of requests for this gauge but I can't always get them for a good price. I recently got a good deal on them so I'm making them available for $18.00 shipped.
Can you take a reading with a tensioner engaged?
Take a reading both ways. If the reading with the tensioner DISENGAGED is within specs, then the reading with the tensioner ENGAGED will also be within specs. In this case, simply note the reading with the tensioner engaged as that is what your 'Normal'. That way you won't have to mess with the tensioner every time you want to take a reading. As I said, the tensioner may not make much if any difference.
Is Krikit II belt tensioner easy to use?
I've gotten a lot of inquiries about setting the proper belt tension with the Krikit II. This tool is simple, very easy to use and quite accurate when done correctly. But you need numbers!
What gauge to use for belt tension?
Always use a belt tension gauge that indicates static tension, such as the Gates Krikit® Tension Gauge, to determine proper tension from the Installation Chart. Tension ranges below are for drives requiring single belts. If multiple belts are needed for a drive, divide tension by number of belts to give per belt tension to be measured.
What to do if your belt tension drops?
If belt tension drops below Suggested Tension range, retighten belt to Installation Tension. This will allow the belt to seat-in and run at Suggested Tension after it has operated under normal driving conditions.
Do micro V belts need tension?
Many Micro-V belts are automatically tensioned by a spring-loaded automatic tensioner, which does not require tension to be set. The tension ranges below are used for applications requiring manual tensioning. For drives with manual take-up on locked-center drives, position the belt and set tension to the prescribed Installation Tension.