To install your Hasp Lock in 3 easy steps:
- 1) Remove your old deadbolt or keyed cylinder from the sliding door. Make sure you take out any screws that may be holding it in place.
- 2) Insert the Hasp Lock into the track on either side of the sliding door, making sure they slide smoothly into place. ...
- 3) Bolt your Hasp Lock in place and then install the deadbolt or keyed cylinder.
What are HASP locks?
Basic hasp locks for doors consist of a locking arm that’s hinged to a plate and a smaller plate with a swiveling or stationary loop for a padlock. More expensive styles have a keyed lock instead of a loop and come in a variety of finishes.
How do you put a hasp on a door lock?
Push the door closed. Fold the hinged locking arm of the hasp against the mounting plate. Position the arm and plate assembly horizontally at the face of the door on the handle side above the existing door handle. Move the assembly, as necessary, so the mounting plate is centered from side to side on the vertical trim at the side of the doorway.
How do you put a padlock on a door with a loop?
Fit the padlock loop that's attached to the smaller padlock plate into the slot on the hinged arm from the back of the arm. Push the plate and arm against the face of the door. Make reference marks on the door at the top, bottom and outer edges of the plate. Take the padlock plate out of the hinged arm.
How do you attach a padlock to wood trim?
Attach the mounting plate at the face of the trim by driving a 2-inch wood screw at each machined hole on the plate. Fit the padlock loop that's attached to the smaller padlock plate into the slot on the hinged arm from the back of the arm.
What is a hasp lock?
How to install a hasp on a door?
What to use instead of screws to mount a padlock plate?
How to put a padlock on a door?
See 1 more
About this website
How does a locking hasp work?
The lockout hasp is placed through a latch on the machinery to be locked out and each person carrying out maintenance or service work attaches their padlock through one of the six openings within the lockout hasp. All of the padlocks are then locked.
How do you attach a hasp to a door?
2:083:02Master Lock | Hasp Installation - Standard and Hinged HaspsYouTubeStart of suggested clipEnd of suggested clipUse a screwdriver to mount the hasp arm to the door. Close the door to verify that it opens andMoreUse a screwdriver to mount the hasp arm to the door. Close the door to verify that it opens and closes smoothly.
How does a steel lockout hasp work?
This means that the energy source is completely locked out and can't be operated until each worker unlocks their padlock from the hasp. Lockout Hasps clip on to several different areas of a hazardous energy source, ensuring that it can't be switched on (LOCKED OUT) and tagging it visually (TAGOUT).
When would you use a hasp?
In order to allow for more than one lock on each energy disconnect, a hasp is used. The hasp is a lockout tagout device that allows for six different locks to be placed on any energy disconnect.
Does the hasp go on the door or the frame?
A hasp & staple comprises a hinged hasp that is typically fitted to the side of a door, and a loop on a plate (the staple) that is fitted to the surrounding structure/doorframe and that is protected by the hinged plate of the hasp when secured.
What is a hasp on a door lock?
Noun. A hinged clasp used for securing a door, lid, etc. Hasps usually pass over a staple and are fastened by a pin or a padlock. A metal fastening hinge consisting of a strap with a slot that fits over a staple and is secured by a pin, bolt, or padlock.
What is a safety hasp used for?
The hasp can be used to ensure that equipment remains inoperative while adjustments or repairs are being carried out.
What is a yellow lock for?
Yellow Caution Locks & Tags Yellow caution locks and tags are used to indicate equipment as being out of service.
Why would you choose a hasp in Loto?
The variety of hasps available in the market allows workers to isolate any energy source required effectively. Additionally, padlocks applied to the Lockout Hasp are well-distinct with different colors; it tells which engineer has the key. This feature enhances safety.
What does hasp mean?
Houston Automatic Spooling Priority, a system program for IBM System/360 and IBM System/370 mainframe computer systems. Hasp key, a Hardware Against Software Piracy copy-protection dongle.
How do I lock out my tag out?
8 Steps of a lockout tagout procedureSTEP 1: Notify affected employees. ... STEP 2: Identify procedure and hazards. ... STEP 3: Shut down. ... STEP 4: Isolate machine from energy source. ... STEP 5: Apply lockout tagout devices. ... STEP 6: Check stored energy. ... STEP 7: Verify isolation. ... STEP 8: Bring equipment back on line.
Can you lock a disconnect in the on position?
Question: Can the disconnect switches be locked in the closed (on) position? Response: There is no provision in the OSHA regulations that prohibits locking the disconnecting means in the closed (on) position.
How do you lock a door that doesn't have one?
To lock a door without a lock, try one of the following:Barricade the door.Use a door wedge.Tie the handles.Remove the door handle.Buy a portable lock.
How do I lock my bedroom door?
2:348:53How to Install a Bedroom/Bathroom Privacy Door Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you want to make sure that it's in the right. Direction. And then i'm just going to use the twoMoreSo you want to make sure that it's in the right. Direction. And then i'm just going to use the two screws that came with the kit. To just screw.
What is a hasp and staple?
Hasp and staple fittings are usually used to secure outdoor buildings or gates, with use of a padlock. The hasp is fitted to the door, gate or storage box, and fits over the staple so it can be secured with the lock. The range includes a choice of materials and finishes.
How do you install a deadbolt on a door?
4:225:58How to Install A Deadbolt Lock - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo fit the deadbolt. Make sure the top is pointing. Up slide it into the hole. And attach theMoreTo fit the deadbolt. Make sure the top is pointing. Up slide it into the hole. And attach the faceplate with screws retract the deadbolt if it's not already.
Julian Cassell's DIY Blog » Blog Archive Fitting a hasp and staple for ...
1. Use a bradawl or pencil to mark the fixing holes for the hasp and then drill pilot holes so that you can screw the hasp in position. Â 2. Using the fixings provided, fix the hasp to the door.
Hasp and Staple | Door Locks & Bolts | CPC
Hasp & Staple. One of the simplest ways of securing a door, lid, or lockable cover is by using a hasp and staple. A hasp is a hinged fastener that fits over a metallic loop, called a staple.
What is a hasp lock?
Hasp locks are useful for outbuildings like sheds, garages or areas of the home where chemicals or other unsafe items are stored. A do-it-yourself homeowner can install a hasp lock with basic tools.
How to install a hasp on a door?
Push the door closed. Fold the hinged locking arm of the hasp against the mounting plate. Position the arm and plate assembly horizontally at the face of the door on the handle side above the existing door handle. Move the assembly, as necessary, so the mounting plate is centered from side to side on the vertical trim at the side of the doorway.
What to use instead of screws to mount a padlock plate?
Always use bolts instead of screws to mount the padlock plate on a hollow-core door.
How to put a padlock on a door?
Fit the padlock loop that's attached to the smaller padlock plate into the slot on the hinged arm from the back of the arm. Push the plate and arm against the face of the door. Make reference marks on the door at the top, bottom and outer edges of the plate. Take the padlock plate out of the hinged arm.
What is a hasp lock?
Hasp locks are useful for outbuildings like sheds, garages or areas of the home where chemicals or other unsafe items are stored. A do-it-yourself homeowner can install a hasp lock with basic tools.
How to install a hasp on a door?
Push the door closed. Fold the hinged locking arm of the hasp against the mounting plate. Position the arm and plate assembly horizontally at the face of the door on the handle side above the existing door handle. Move the assembly, as necessary, so the mounting plate is centered from side to side on the vertical trim at the side of the doorway.
What to use instead of screws to mount a padlock plate?
Always use bolts instead of screws to mount the padlock plate on a hollow-core door.
How to put a padlock on a door?
Fit the padlock loop that's attached to the smaller padlock plate into the slot on the hinged arm from the back of the arm. Push the plate and arm against the face of the door. Make reference marks on the door at the top, bottom and outer edges of the plate. Take the padlock plate out of the hinged arm.
