how do you use a jandy valve manually

Manual Override, Power Off (Jandy and should work for others) Move toggle switch located on the bottom of actuator to the OFF (center) position. Unscrew (counterclockwise) the locking knob above the handle four (4) full turns. Push down on the locking knob (not the handle). This will disengage the gear train and allow the handle, and thus the valve diverter, to be moved to any position.

Full Answer

How do I use Jandy neverlube valves?

1. name "NeverLube" on the handle.Turn OFF power to the actuator. 2. Remove the locking knob and handle (see Figure 13). 7. Turn handle once around to spread the lubricant. 8. Pull up on the handle and tighten locking knob. 5.2 Valve NOTEThis section does not apply to Jandy NeverLube Valves and non-positive seal valves. NeverLube

How do you mount a JVA on a Jandy valve?

JVA’s mount directly on all full-size JandyPro Series Valves (8 screws on lid). Zodiac recommends motorizing Jandy Pro Series Never Lube®Valves only. JVA’s may be mounted onto valves in any of the four (4) positions in Figure 3.

How do I contact Jandy valve actuators?

this manual contact 707-776-8200, ext. 237. For address information see back cover. 2.2 Description Jandy Valve Actuators are designed to meet the needs of today's more advanced, automatic pool equipment. These fully adjustable actuators offer

Where can I get a manual for the Jandy®CL cartridge filters?

This manual contains information for the proper instal- lation and operation of the Jandy®CL and CV Series Cartridge Filters. Procedures in this manual must be followed exactly. To obtain additional copies of this manual contact us at 707.776.8200 ext. 237. For address information see back cover.

Can you manually turn Jandy valve?

There are two (2) methods of manually rotating the JVA; one with power on (system operational) and one with power off (no power to the control system). 1. Move the toggle switch located on the bottom of the actuator to the opposite position (ON 1 switch to ON 2 or vice versa).

How do you turn on a Jandy valve?

0:348:38How to cam a Jandy valve actuator - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you flip it to one side it will turn into one direction if you flip it to the other side thenMoreSo if you flip it to one side it will turn into one direction if you flip it to the other side then it will turn into the other direction.

How do you tell if a Jandy valve is open or closed?

0:341:52Tips and Tricks - How to Open and Close a Pool Valve - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition notice the off off. Means no flow obviously there's no electricity flowing through theMorePosition notice the off off. Means no flow obviously there's no electricity flowing through the valve here it just means no flow.

How do you control a Jandy valve actuator?

0:2711:49How to set/orient valve actuators for pool mode and spa mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you open it up. And you'll see the cord wrapped around the top. This is the jandy actuator rightMoreSo you open it up. And you'll see the cord wrapped around the top. This is the jandy actuator right here. And what you're gonna find is that um there is a little switch on the bottom of this actuator.

How do Jandy pool valves work?

0:323:05POOLCENTER.com - Jandy Swimming Pool Valve Info. - Part TwoYouTubeStart of suggested clipEnd of suggested clipNow the way this valve operates is this diverter as it's called will go in and close the port whenMoreNow the way this valve operates is this diverter as it's called will go in and close the port when the port is closed. The word off will line up with the port that's closed.

How does a Jandy 2 way valve work?

Diverter Valve Jandy diverter pool valves divert water and are available with two or three ports. A 2-port valve essentially acts as a 1-way-in / 1-way-out valve, allowing for water flow to be shut off completely or to restrict the flow of water for a lower flow rate.

How do I manually turn my pool valve on?

1:282:53Pool Valve Actuator Manual Mode & Manual Override part 1 of 2YouTubeStart of suggested clipEnd of suggested clipIf the manual override command we overwrite the value three turns or so you want to push down firmlyMoreIf the manual override command we overwrite the value three turns or so you want to push down firmly. And you should be able to turn the handle now. And the reengage if you simply lock it back down.

Which way do you turn a valve to open it?

0:241:56Which Direction to Turn on Plumbing Valves? : Plumbing Help - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn you turn it counterclockwise that opens your gate.MoreOn you turn it counterclockwise that opens your gate.

How do I know if my water valve is open?

To determine if a water valve is open or closed, there is a simple general rule you can usually follow. Basically, if the handle is turned 90 degrees to the flow, the valve is switched off.

How do I adjust my pool valve?

3:518:43How To Understand Pool Valves - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's as easy as closing the suction from the spa and closing the return to the pool. This will pullMoreIt's as easy as closing the suction from the spa and closing the return to the pool. This will pull water from the pool and return it to the spa elevated spa setups this creates a nice waterfall.

How does a pool valve actuator work?

What is a Pool Valve Actuator? Pool valve actuators provide an automated command by push-button that goes to one of the diverter valves or more in the pool's water flow system. You will find it on your pool's diverter valve and it will be wired in the pool's control box.

How does a valve actuator work?

Torque is the rotational force an actuator generates to close a rotational valve. Electric actuators can generate this force by transmitting it to the output shaft and then the valve stem. When pressure is applied to the valve stem, the valve's orifice opens or closes.

How often should I lubricate a pool valve diverter?

Since the actuator rotates the valve diverter which redirects the flow of water, it is imperative that the seals and the O-rings within the valve body be lubricated often (at least every three (3) months). Use the following procedure to lubricate the valve diverter seals: 1. Turn off all pool/spa equipment. 2.

How many seals does a JVA actuator have?

6.1 Actuator. The JVA has three (3) seals which should be lubricated once a year. One o-ring is located on the bottom of the actuator where the plastic shaft exits the housing and two (2) O-rings located in the top cover near where the shaft exits the top of the housing.

What is a 3 way valve?

Jandy Valves. The most common variety of valve found on pool plumbing is a 3-way valve, popularized by Jandy, and copied by Compool, Hayward and CMP. Robert Ortega, working for Purex was the first to patent a 3-way pool valve in 1980, but it didn’t catch on until Jandy introduced their first model, which was white in color.

How does a diverter valve work?

As you turn the valve handle, the diverter inside rotates in the same direction. The design of the valve, allows you to easily control the flow from two pipes with one valve. One pipe can be completely or partially closed off, while the other port is fully open, or both ports (pipes) can be fully open at the same time.

Is Jandy valve better than ball valve?

Jandy valves are more expensive than ball valves, but their design allows one valve to replace two ball valves, making plumbing simpler and cleaner. 3-way valves are also easier to use than other types of pool valves and newer models require no lubrication.

Do Never-Lube valves need lubricant?

Newer valves, known as Never-Lube, do not need to be manually lubricated. Fill the grease cap on gray models with Magic Lube or similar lubricant annually. After filling the cap, thread the outer cap down to squirt lube into the valve body, onto the face of the diverter.

Can you plumb a valve with pipe?

Another advantage of these valves is that you can plumb with pipe to the inside of the valve, or you can glue a coupling to the outside of the valve port, allowing you to plumb 1.5" or 2" with the same valve. What can be confusing for combination valve users is what is happening inside the valve when they turn the handle.

Can you deadhead a water pump?

Be careful not to accidentally dead head the valve, blocking incoming water flow into the port marked ‘Inlet”. However, deadheading the valve can be useful to block water flow when the pump is off, for repair or maintenance on the pump, filter or plumbing.

Can you buy a Jandy valve without the lid?

You can buy the valve housing separately, without the lid and diverter assembly, but the price of the housing alone is nearly the same as buying an entire new valve. Sticky valves can be lubricated with a Teflon based lubricant. Older grey Jandy valves will have a grease cap that can be filled with lube.

Section 1. Safety Information

Section 2. Bwvl-Sld-75 with SFSM

• The following manual provides instructions for installing the Jandy slide valve BWVL-SLD-75 onto the Jandy SFSM Series filter. The instructions must be followed exactly. Read through the instructions completely before starting the procedure. Please save these instructions. The slide valve is a two-position valve. The valve handle must be fully exte...

See more on manuals.plus

Section 3. BWVL-SLD with Dev Or JS Series Filter Installation

Section 4. SVLV8 with Del Series Filter Installation

Section 5. SVLV2 with Non-Jandy Filter Installation.

Section 9. Slide Valve Exploded View and Replacement Parts List