Climb into the whirlpool bathtub carefully. Hold onto something sturdy while getting into the tub to avoid slipping. Sit down in the bathtub and make yourself comfortable. Press the "On/Off" control on the side of the tub to turn on the pump and start the whirlpool jets. Wait for up to a minute while the pump primes.
What should you not put in a Kohler whirlpool tub?
DO NOT use attachments not recommended by the Kohler Co. Keep small objects such as bath toys and bathing accessories out of the whirlpool while the pump is operating. NOTE: Whirlpool action can cause even a small amount of bubble bath, bath soap, shampoo, or bath oil to foam excessively.
How do you use a whirlpool tub step by step?
Fill the tub with water set to your temperature preference. Run the water at least two inches higher than your tub's highest jet or water level sensor. Climb into the whirlpool bathtub carefully. Hold onto something sturdy while getting into the tub to avoid slipping. Sit down in the bathtub and make yourself comfortable.
How do you turn off the Jets in a whirlpool bathtub?
Press the "On/Off" control on the side of the tub to turn on the pump and start the whirlpool jets. Wait for up to a minute while the pump primes. Once the pump is primed, the jets will activate. Press the "On/Off" button at the end of your bath to turn off the whirlpool jets. Drain and rinse the whirlpool tub at the end of each bath.
How do you take care of a whirlpool bathtub?
Take care to avoid slipping while using your whirlpool bathtub. Circulating oil into the jet system will promote the growth of bacteria. Do not use bath products that contain oil additives when using the whirlpool jets. Soaking in a luxurious whirlpool bath is the perfect way to end a long, tiring day.
How do you use a whirlpool jetted tub?
0:030:43Using the Jacuzzi Tub in the Downstairs Bath - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then turning on the Jets in the jacuzzi tub is just this button here one press to turn on oneMoreAnd then turning on the Jets in the jacuzzi tub is just this button here one press to turn on one press to turn off because there's no water in it I won't turn it on right. Now.
How do you turn on a Kohler bathtub?
1:1511:58Kohler Whirlpool Tub Operation. - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the power switch for the tub is actually connected to this GFCI switch right here see that rightMoreAnd the power switch for the tub is actually connected to this GFCI switch right here see that right there.
How do I get my whirlpool tub to work?
Set the water temperature for your bath. ... Fill the tub with water set to your temperature preference. ... Climb into the whirlpool bathtub carefully. ... Press the "On/Off" control on the side of the tub to turn on the pump and start the whirlpool jets.More items...
What does the button on a Jacuzzi tub do?
Some larger hot tubs may have up to three jet buttons on the control panel that allow you to adjust the speed and strength of your jets. In most cases, pushing the button the first time will turn them on a low setting and pushing it again will increase the speed.
What are the knobs on my Jacuzzi tub?
Water Control Generally, in the form of manual knobs, there are electric versions, but the idea is that the water knobs control the speed and pressure of the jets. Some of these are tied and linked to your electric water pump.
Why is my Jacuzzi tub not working?
If the jets do not work, clear a blocked water intake of hair and other particles (see below) or replace a broken jet (see below). If the water in your spa or hot tub is too hot or too cold, check to see if the high-limit reset switch has been tripped and, if needed, reset it.
How do I turn on the jets in my hot tub?
Many Master Spas hot tubs have adjustable jets. By turning the outer ring of the jet, you can turn it on or off. Turn it clockwise for full pressure. To turn off an individual jet, turn it counter-clockwise.
What is the difference between jetted tub and jacuzzi?
The first whirlpool tub was patented by Jacuzzi. The company's products have since become synonymous with in-home spa tubs and, while Jacuzzi is a brand name, it is often used interchangeably with "whirlpool" or simply any jetted tub. Whirlpool is the generic term for any tub with water jets installed.
Where is the reset button on my jetted tub?
You will find a reset button typically on the heater unit. Usually there is a pilot light. When you're ready to reset, push the button. Some spa units have a high limit switch which will turn off the spa heater if the thermometer fails.
How do you use hot tub buttons?
3:104:46Hot Tub Control Panel Overview - Touchscreen - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can turn each of the therapy pumps on/off or adjust the speed. Just by pressing the appropriateMoreYou can turn each of the therapy pumps on/off or adjust the speed. Just by pressing the appropriate button. Remember some therapy pumps may only be one speed.
What do the two knobs on a hot tub do?
Air controls are the knobs on the side of the spa that are used as air intakes. Some spas have several air control knobs, which control the amount of air intake (and thus air output) for a certain group of spa jets, or a particular air manifold.
Do hot tub jets turn off automatically?
The water jets on almost all systems (Balboa, Gecko, Smart Touch, etc.) will only run for a fixed time, usually 15 or 20 minutes, and then will automatically switch off.
How do I turn on my Kohler shower?
0:022:04Kohler Shower - How to Use - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i'm going to show you how to use this kohler shower all right. So it could be a little bitMoreAnd i'm going to show you how to use this kohler shower all right. So it could be a little bit confused. And hopefully i can help resolve those issues uh before we get started give me a thumbs up as
How do I start my Kohler shower?
0:403:49Kohler DTV Prompt - Digital Showering System - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt to begin or end your shower. Simply activate the power button while showering you can adjust theMoreIt to begin or end your shower. Simply activate the power button while showering you can adjust the water temperature by selecting the red arrow for warmer water or the blue arrow for cooler water.
How do I use my Kohler diverter?
OPERATION INSTRUCTIONS Turn the diverter handle to the vertical upwards, water will flow from the handspray; turn it to the vertical downwards, the showerhead will work; turn it to the position between the vertical upwards and the vertical downwards, water will flow the showerhead and the handspray.
How do I turn on my Kohler shower speaker?
0:242:13How Does The KOHLER Moxie Showerhead + Bluetooth ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSection turn your Bluetooth on and it will sync. We're synched and then like any other BluetoothMoreSection turn your Bluetooth on and it will sync. We're synched and then like any other Bluetooth unit. You can go to your music. And you can play whatever you want.
Where is the water suction inlet on a Kohler whirlpool?from manualslib.com
Adjustable Jets Water is drawn from the bath through the water suction inlet located near the bottom of the bath.
How long is Kohler's warranty?from kohlerpower.com
Kohler offers you up to three years of guarantee. Please refer to this section to see the engines maintenance guarantee conditions specific to your engine.
Can you use hydromassage in a hot bath?from manualslib.com
DO NOT use this hydro-massage DANGER: Risk of Injury. Hot whirlpool baths bath. Disconnect the hydro-massage bath and have can put certain stresses on the body, as does any hot bath, shower, sauna, or steam bath.
How to set water temperature in whirlpool?
Depending on the make and model of your whirlpool, the temperature control may consist of a simple knob or an intricate electronic control panel. For best results, set the temperature between 100 and 102 degrees F. Purchase a thermometer from a local pool supply store to monitor ...
How to make bubbles in a whirlpool bath?
Make luxurious bubbles a part of your whirlpool bath experience. Add one to two drops of a biodegradable liquid to your bath water to create just the right amount of bubble. Take care not to add too much soap to the water or you risk having the bubbles spill out onto the floor.
How to activate whirlpool jets?
Press the "On/Off" control on the side of the tub to turn on the pump and start the whirlpool jets. Wait for up to a minute while the pump primes. Once the pump is primed, the jets will activate.
Why do people take whirlpool baths?
Whirlpool baths are said to relieve stress, as well as relax tired, sore and achy muscles. Having a whirlpool bathtub in the privacy of your own home is more convenient than using a hot tub at a gym or fitness center. Learning how to operate a whirlpool bathtub is relatively simple, leaving you more time to soak in the glorious experience.
Can you use a whirlpool jet in a bathtub?
Take care to avoid slipping while using your whirlpool bathtub. Circulating oil into the jet system will promote the growth of bacteria. Do not use bath products that contain oil additives when using the whirlpool jets. Soaking in a luxurious whirlpool bath is the perfect way to end a long, tiring day.
What is a Kohler chromatherapy?
KOHLER ® Chromatherapy is a lighting system that uses the soothing qualities of color to let your mind and body drift and dream as you relax into a warm bath.
Can you add a non-factory heater to a whirlpool?
KOHLER does not recommend adding a non-factory installed heater to whirlpool s or baths.
Can you use bubbles in a whirlpool?
Oils and Bubbles. KOHLER does not recommend using oils or bubbles in whirlpools. These products could coat the recirculating PVC jet harness and dry out the bearings and seals inside the pump. This could cause build up and disperse black flecks out of the jets.
How to make a bath with no air induction?
Adjust the jets fully clockwise so there is no air induction. Fill the bath with warm water to a level 2" above the highest jets, or leave water in the bath after using. Add 2 teaspoons of a low-foaming, powder automatic dishwashing detergent and 20 ounces of household bleach (5% to 6% sodium hypochlorite) to the water. ...
Can you rinse a bath with water?
If desired, rinse baths surfaces with water.
Where is the label on a Whirlpool bath?
Whirlpools. Whirlpools manufactured before 1990: The label is attached to the shell of the bath near the pump assembly, or adhered to nearby piping. Whirlpools manufactured 1990 and later: The label is attached directly onto the pump assembly.
Where is the model number on a Whirlpool pump?
A label containing the model number and serial number may also be located under the drain overflow hole.
Where is the serial number on a bath?
Newer baths have serial number labels under the overflow hole. The label will be visible prior to installation and removed or covered after installation.
Where is the label on a bath tub?
The label is typically located near the drain end of the bath.
Does the installation guide include the model number?
Depending on the bath style, the front cover of the installation guide may include the model number. If the purchase invoice or installation guide is not available, contact the Customer Care Center at 1-800-4KOHLER for assistance.
How long does it take for a Kohler walk in tub to purge?
This purge takes approximately one minute. If you think any noise coming from your jets is abnormal, contact your installer or manufacturer.
How Often Should You Clean Your Tub?
For the best results, clean your whirlpool jets at least twice a month. If you use your walk-in bath more than three times per week, we recommend cleaning the whirlpool jets more than twice a month.
Can you make your own jet tub cleaner?
You can make your own jet tub cleaner with household items! Combine the following ingredients:
Can you use a jet cleaner in a bathtub?
You can use a homemade bathtub jet cleaner to deep clean the tub and keep the jets running properly. Explore this blog to learn how and when to clean your jetted tub.
How to clean gooseneck shower arm?
Gooseneck shower arm: Use soft, dampened sponge or cloth to wipe spray face and nozzles. Run the water for a minute or two to clear any remaining debris. Bath Screen: Wipe the screen dry with a soft cloth to avoid soap deposits or lime buildup in hard water areas.
Can you use Kohler walk in bath cleaner?
Do not use them to clean your KOHLER ® Walk-In Bath. Since the hardness and temperature of your water varies and affects the mixture of cleaning materials, KOHLER cannot guarantee the effectiveness of the formulas mentioned. Clean your Walk-In Bath and faucets with care.
How often should I clean a whirlpool tub?
Cleaning Frequency. This really depends on the frequency of use, but I recommend using this method monthly to quarterly if you use your whirlpool tub frequently and biannually or annually if you use your tub infrequently.
How to clean a jetted tub?
Begin by filling your tub with hot water to about three inches above the jets. Add four tablespoons of powdered dishwasher detergent and 1/2 cup of vinegar to the water. The detergent will serve to loosen and remove any greasy residue left behind by soap or bubble bath from the jets while the vinegar will disinfect. Turn the jets on at full capacity and allow it to run for 15 minutes.
