How to Use a Kreg Pocket Hole Jig
- Step 1: Determine pocket hole placement I find it is easiest to mark all of your pieces first, so you can drill all of your pocket holes at one time. ...
- Step 2: Determine screw size ...
- Step 3: Set Drill Guide Height ...
- Step 4: Set Drill Bit Depth Collar ...
- Step 5: Drill your pocket hole ...
- Step 6: Attach the pieces with screws in the pocket hole ...
How to use a KREG jig on a 2x4?
You might require the following instructions:
- The first step is always to measure the thickness of your material.
- Then mark with a pencil on that piece of wood, where you want to make the pocket holes.
- After you have done this, set the drill guide in your Kreg jig. ...
- Align the thickness mark according to your measurement and lock it down.
- Then you have to set the stop collar on the bet.
How to choose the correct KREG screw?
You can never choose any random size of the screw for your Kreg Joinery. It is important to select the appropriate size to avoid any malfunctioning. Screws used for Kreg Joinery comes in three types: zinc screws, blue coat weather resistant screw, and stainless steel screw. These types of screws vary from one another regarding the conditions they are used in.
Do you have to use KREG jig screws?
You really do need to use Kreg screws when using the Kreg jig. The screws come specially designed to work with the holes that are drilled by the Kreg jig. Trying to use other screws will not properly bring the wood together. Can Kreg screws be used outside?
What is the best KREG jig to buy?
- The Kreg Jig Jr (R3) is an amazing repair jig and an exceptionally handy addition to any tool collection
- Easy to use and install
- Whether you're crawling under a table to make a quick repair or taking Kreg Joinery on the road
- Pocket hole jig system for do-it-yourselfers
- Easy to adjust for materials 1/2-Inch to 1-1/2-Inch
How to drill pocket holes in wood?
What is a kreg jig?
How to keep a jig from coming loose?
What is a jig for wood?
How to adjust a jig?
What is depth collar?
Why use pocket holes in antique furniture?
See 4 more
About this website
Can you use regular screws with Kreg pocket holes?
You really do need to use Kreg screws when using the Kreg jig. The screws come specially designed to work with the holes that are drilled by the Kreg jig. Trying to use other screws will not properly bring the wood together.
Do you have to pre drill for pocket screws?
As you drive a pocket-hole screw into your material, the pocket and pilot hole guide the screw precisely, while the screw's self-tapping tip drills its own hole into the mating piece. That means you don't have to drill into both pieces, and you'll get great holding power without splitting or stripping the wood.
How do you use the Kreg drill guide?
0:032:10Kreg® Drilling Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe kreg drilling guide makes it easy to drill perfectly straight holes without using a drill. PressMoreThe kreg drilling guide makes it easy to drill perfectly straight holes without using a drill. Press with the drilling guide you can drill straight perfectly position holes using just a hand drill.
How do you set the depth on a pocket hole jig?
0:171:23Quick Tip: Set Up Your Kreg Jig® R3 in 3 Simple Steps - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust slide the drill bit in move the stop collar. Until it aligns with the thickness that you need.MoreJust slide the drill bit in move the stop collar. Until it aligns with the thickness that you need. And then tighten it down now you're all set to drill pocket holes at the perfect depth.
When should you not use pocket screws?
4:239:28When to NOT use pocket screws... and when you SHOULD! - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have two options you either put in a wood plug. Cut it flush. And then sand it or you can justMoreYou have two options you either put in a wood plug. Cut it flush. And then sand it or you can just design your piece of furniture. So that the pocket holes are on the back side.
Should you use glue with pocket screws?
The simple answer to this question is yes. You can assemble pocket-hole joints without glue. We've always said that a joint made with Kreg Pocket-Hole Screws is so strong that glue is optional. That means you can use glue if you want, but it's not necessary in order to create a strong, lasting joint.
What depth should I set my Kreg jig?
Adjust the depth collar to 3-5/16" (84mm) from the step of the bit for 1/2" (13mm) material and 4-1/4" (108mm) from the step of the bit for 1-1/2" (38mm) material. To set the depth, simply slide the Depth Collar onto the loose drill bit shank (the bit should not be chucked into the drill).
Do you need a jig for pocket holes?
But can you make pocket holes without a jig? You sure can. I'll leave it for you to decide whether it's worth it. You just need to drill an angled hole, then drill a wider hole.
What depth should I set my Kreg jig for 2x4?
Kreg Jig K4 Material Depth Guide Locations This one is set to 1-½” for drilling into a 2×4.
How far from the edge should a pocket hole be?
There are no hard and fast rules for spacing pocket holes on edge joints but typically you should place pocket holes 2″ from the end of a board and then typically space pocket holes 6″ apart along the edge of the board. Use wood glue and clamps to create a quality joint.
What is the best pocket hole jig for beginners?
The Kreg R3 is the best pocket hole jig for beginners. It's simple to use, affordable and includes most everything needed to make repairs and build DIY furniture. The Kreg Jig R3 is a great choice for newbies to get started with pocket hole joinery.
How much space should be between pocket holes?
6″ to 8″Pocket-hole spacing in plywood, panels, and long boards Whether you're drilling along the edge of long boards or you're working with sheet goods, our recommendations for spacing are the same. Place a pocket hole close to each end, and then space them out every 6″ to 8″ in between.
Do you drill pilot holes for pocket screws?
An angled pilot hole is drilled into the face of one of the mating pieces near the end. The shallow angle of the pilot hole allows the pocket screw to exit the end of the workpiece and enter the edge of the mating piece, pulling them tightly together.
Is Pre drilling necessary?
When you drive screws into wood without drilling pilot holes, you're essentially pushing wood out of the way to make room for the screw. That displaced wood puts more pressure on the wood surrounding the screw, which can lead to splitting and cracking, weakening the wood over time.
Should you pre drill for screws?
Pilot holes are necessary to prevent damage to the material and allow the screw to better fit into the material. You could try to drill without pilot holes but depending on your screw size and wood type it will likely split or crack the lumber.
Can you drill pocket holes without a jig?
But can you make pocket holes without a jig? You sure can. I'll leave it for you to decide whether it's worth it. You just need to drill an angled hole, then drill a wider hole.
How To Use A Pocket Hole Jig - Extreme How To
What is a Kreg Jig. A Kreg Jig is a tool used to join wood. Kreg Jigs allow you to drill an angled screw hole and pilot hole. A “Robertson” self-tapping pan head screw is then inserted at that angle, along the grain of the wood rather than through it, creating a strong joint.
How to drill pocket holes in wood?
Before you begin drilling, it’s important to measure the width of the boards you’ll be working with. The thickness is what you’re looking to gauge here. Knowing the exact thickness of the board will enable you to drill the pocket holes at just the right angle.
What is a kreg jig?
Learn more... A Kreg Jig is a type of tool used to join wood. Kreg Jigs can help you drill what are known as pocket holes, which allow screws to be inserted at an angle. Because the screws run along the grain of the wood rather than through it, the joint will be much stronger and more secure.
How to keep a jig from coming loose?
Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place. This will prevent the wood from coming loose while you’re drilling. Make sure the guide holes of the jig are facing toward you on the workbench.
What is a jig for wood?
The jig will allow you to drill at a shallow angle into the wood, which results in a more structurally sound joint than if you were to drill straight through.
How to adjust a jig?
Change the placement of the jig. Using the same measurements, adjust the height of the jig to the appropriate position. To do this, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely. Once the jig is where you want it, tighten the thumbscrew to secure it.
What is depth collar?
The depth collar is slightly wider than the guide holes of the jig, and will keep you from drilling too far into the wood.
Why use pocket holes in antique furniture?
Use pocket holes to reinforce the joints in your favorite antique furniture pieces and increase their lifespan.
Step 1: Determine pocket hole placement
I find it is easiest to mark all of your pieces first, so you can drill all of your pocket holes at one time. This is especially useful when you have a lot of pocket holes to drill, as it cuts down on time.
Step 2: Determine screw size
See my tips below for which screw you need to use. The Kreg screws are self-tapping so they won’t split the wood and eliminates the need to pre-drill holes.
Step 3: Set Drill Guide Height
This setting is on your actual jig. You will set this setting to the thickness of the thinnest board you are joining. Lock this in place before moving on.
Step 4: Set Drill Bit Depth Collar
This will control the depth of the hole you drill into your piece. Align the step collar on the bit to the guide on your jig that matches your wood thickness. Tighten the collar with the provided allen wrench.
Step 5: Drill your pocket hole
Using one of the three drill bit guides of your choice, plunge your drill until you reach the depth collar. Place the pocket holes 6-8 inches apart if you are joining long pieces together. Two pocket holes are generally needed so your piece doesn’t twist.
Step 6: Attach the pieces with screws in the pocket hole
Use the screws that you chose (tips below), along with the provided drill bit and clamps to secure the screws within the pocket hole. Glue is optional, although it will make your joint much stronger.
What is a Kreg Pocket Hole Jig?
A pocket hole jig is a tool that is used for tightening screws in woodwork. It helps in making the end product look much more professional and well-polished.
What to do if a jig gets stuck?
If your jig gets stuck and does not make a hole, clear the sawdust from the area when you are trying to make a pocket hole. If this does not work, change the location of the pocket hole as there might be a knot in that region.
Can you mess up a pocket hole jig?
There is only one hole that you are working with. So, you cannot mess it up.
What screw to use for pocket hole?
I always recommend using square-drive pocket hole screws. They drive quickly and easily without stripping. Make sure you have the appropriate length and thread type for the material. These are available from Kreg Tool as well.
What is pocket hole jig?
The Pocket Hole Jig is a brilliant little tool that helps you create joints. We show you how to use a Kreg Jig to make pocket holes perfectly every time. It’s hard to deny the visual appeal of a wedged tenon, tight dovetails, a double bridle joint, or maybe just a simple rabbet joint with different woods. If you’ve yet to develop those skills or you need to quickly create strong joints that aren’t for show, there’s hope for you!
Where does the waste come from when you drill a pocket hole?
As you drill the pocket hole, waste comes out of the bottom of the drill guide. Some versions of the Kreg Jig even include dust collection.
Can you use a drill for impact driver?
You can use a drill, but a cordless impact driver on the middle setting works wonders for this type of work.
Can you make pocket holes with a jig?
Believe it or not, those are the steps. Anyone can make perfect pocket holes with this jig. It just takes a few minutes to set up properly, and you can pretty much automate the process for perfect drawers, shelves, and more.
How thin can you drill pocket holes?
Pocket holes can be drilled in material as thin as a half-inch to an inch and a half. Keep this in mind when you are selecting the material for your projects.
What is pocket hole joinery?
Becoming familiar with pocket hole joinery is a great way to get acquainted with joining two pieces of wood together to create picture frames, shelves, furniture pieces, and more.
How many holes are there in a pocket hole jig?
There are three holes (aka drill guides) on the pocket hole jig labeled A, B and C.
How to secure a docking jig to a work surface?
Fold out the docking wings to provide a nice stable surface. You can also secure the jig to your work surface using the clamp.
When to use 320 jig?
We also use the 320 when we’re working with really long pieces of wood that we’d have trouble standing up on the traditional pocket hole jig ( like the large face frame we built for these mudroom lockers ).
When will the Kreg 520 Pro be released?
The 520 Pro was released by Kreg at the same time as the 720 Pro in 2021 and replaced the old K4 pocket hole jig. Kreg calls it their “most versatile jig” due to an easy-to-use system that can be used on the go.
How to secure a clamp on a wood table?
Place the piece of wood into position, then slide the clamp down and secure. That’s all!
How to drill pocket holes in wood?
Before you begin drilling, it’s important to measure the width of the boards you’ll be working with. The thickness is what you’re looking to gauge here. Knowing the exact thickness of the board will enable you to drill the pocket holes at just the right angle.
What is a kreg jig?
Learn more... A Kreg Jig is a type of tool used to join wood. Kreg Jigs can help you drill what are known as pocket holes, which allow screws to be inserted at an angle. Because the screws run along the grain of the wood rather than through it, the joint will be much stronger and more secure.
How to keep a jig from coming loose?
Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place. This will prevent the wood from coming loose while you’re drilling. Make sure the guide holes of the jig are facing toward you on the workbench.
What is a jig for wood?
The jig will allow you to drill at a shallow angle into the wood, which results in a more structurally sound joint than if you were to drill straight through.
How to adjust a jig?
Change the placement of the jig. Using the same measurements, adjust the height of the jig to the appropriate position. To do this, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely. Once the jig is where you want it, tighten the thumbscrew to secure it.
What is depth collar?
The depth collar is slightly wider than the guide holes of the jig, and will keep you from drilling too far into the wood.
Why use pocket holes in antique furniture?
Use pocket holes to reinforce the joints in your favorite antique furniture pieces and increase their lifespan.
