Wearing your elastomeric pump
- Wear your pump in the area between your armpits and hips. ...
- It’s best to keep your pump in the fanny pack your healthcare provider gives you.
- Do not keep your pump under a warm jacket or blanket. ...
- At bedtime, keep your pump next to your side and above your blankets. ...
- Do not sit or lie directly on your pump. ...
How do you use elastomeric infusion?
7:219:07How to use: Intermate Elastomeric Pump (short version) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the other on the connector. And I twist counterclockwise twist the end of the tubing to remove.MoreAnd the other on the connector. And I twist counterclockwise twist the end of the tubing to remove.
How does an elastomeric device work?
An elastomeric device is a device used to deliver medication through your intravenous (IV) line. Medication is put in a balloon-like chamber, and pressure from the balloon delivers the medication at a safe and steady rate. Your nurse will teach you how to use the elastomeric device, and how to flush your IV line.
How do you infuse an elastomeric pump?
2:526:09Administering Medication via Elastomeric Easy Pump at HomeYouTubeStart of suggested clipEnd of suggested clipRemove the end cap from the elastomeric ez pump and attach it to the injection cap of your ivMoreRemove the end cap from the elastomeric ez pump and attach it to the injection cap of your iv catheter by pushing and turning clockwise to secure in. Place. Release the clamp on the elastomeric.
How does an elastomeric infusion pump work?
Elastomeric pumps use pressure to infuse medication. This pressure is created by an elastomeric layer which is molded into the inside of the pump. When the elastomeric pump gets filled, the elastomeric layer becomes stretched. The elastic constriction then drives the liquid that is present through the tubing.
How do you initiate an infusion using an IV elastomeric pump?
Remove the cap on the Elastomeric Pump IV tubing. Unclamp the tubing on the medicine ball (Elastomeric Pump) to ensure there is no air in the line and that it works properly. 3. Attach the Elastomeric IV tubing to your IV line and infuse the medication as directed.
Can you shower with a chemo pump?
If your medication is delivered via a pump, you must also keep the pump dry when bathing. You can try taking your showers/baths at the same time as your medicine bag changes. OR you can place your pump in a clean plastic bag, seal the bag, and hook the covered pump on a shower hook.
How do you prime an elastomeric pump?
0:083:08Easypump® ST/LT Elastomeric Infusion Pump Priming and FillingYouTubeStart of suggested clipEnd of suggested clipTwist Off the cap from The Filling port and place it on the sterile surface attach the primingMoreTwist Off the cap from The Filling port and place it on the sterile surface attach the priming syringe to the filling port. Down the syringe plunger until the syringe is empty.
How do you know when elastomeric pump is done?
Your infusion is finished when the balloon is completely deflated (see Figure 5). Continuous infusion with a pump usually takes about 48 hours.
How long do infusion pumps last?
How Long Can I Expect The Pump To Last? Typically the medication in the pump will last approximately 3 months, though in some cases it may only last a month dependent upon the rate at which the pump is set. Refilling the pump takes places in the office and will only take a few minutes to happen.
What are the three major problems of infusion pumps?
The FDA has summarized the three major reasons for infusion pump malfunctions as the following:Software Defects. Some pumps fail to activate pre-programmed alarms when problems occur, while others activate an alarm in the absence of a problem. ... User Interface Issues. ... Mechanical or Electrical Failures.
In which setting is an elastomeric pump most commonly used?
The elastomeric pump is typically used in acute or chronic (moderate-severe), oncologic or non-oncologic, post-operative pain, when oral therapy is no longer sufficient....This system is mainly used for continuous infusion of:anesthetics;analgesics;anti-inflammatories;chemotherapeutics.
What are the disadvantages of infusion pumps?
Inadequate user interface design ("human factors" issues ): The infusion pump screen doesn't make clear which units of measurement the user is expected to enter. For example, the user may enter weight in pounds when the infusion pump requires it in kilograms. Pump labels or components become damaged under routine use.
What is an elastomeric product?
Elastomer: Polymer that displays rubber-like elasticity. Rubber-like solids with elastic properties are called elastomers. Polymer chains are held together in these materials by relatively weak intermolecular bonds, which permit the polymers to stretch in response to macroscopic stresses.
What is an elastomeric coating?
Elastomeric coating is an above-grade exterior wall or roof coating that is approximately 10 times thicker than paint. It forms an incredibly thick yet flexible coating that helps waterproof the exterior of a structure.
How long before infusing from an elastomeric device should it be removed from the refrigerator?
1. The Infusor should be removed from the refrigerator directly before use unless otherwise instructed. The Intermate should be removed from the refrigerator 4-6 hours before use unless otherwise instructed.