Face frames and drawers on cabinets : High Performance can be successfully applied by hand to cabinet face frames or edges with a brush, pad or small, cabinet-specific roller such as Whizz or AllPro Velour brand.
- Hand application: Apply a liberal amount of product using a synthetic bristle brush, foam brush, pad applicator or roller such as Whizz or AllPro Velour brand. Avoid pressure and excessive back brushing. Brush along the wood grain using smooth, even strokes with light lap marks. ...
- Spray application: Before spraying, strain topcoat through a fine-mesh filter. Spray wet films at 3-5-mil thickness. ...
Which General finishes topcoat should I use?
You can use any of our topcoats. Water-based products include General Finishes High Performance or General Finishes Flat Out Flat. Oil-based products include General Finishes Gel Topcoat or General Finishes Arm-R-Seal. Gel Topcoat is thick, while Arm-R-Seal is much thinner, and is easier to apply large projects.
Do flat out flat and high performance top coatings dry clear?
Water based Flat Out Flat and High Performance top coats dry clear. Never use any water based topcoat with long oils such as Danish, Tung or Linseed. Water based top coats clean up with water. Oil based topcoats require mineral spirits for clean up. Original formula of Enduro-Var ADHERES WELL only over WATER STAINS, DYE STAINS, and RAW WOOD.
How do you apply general finishes high performance polyurethane?
Sand down the final finish with a 220-grit foam sanding pad, and then add another layer of General Finishes High Performance PolyurethaneTopcoat. Apply liberally than you did previously without heavy back-brushing. Let the topcoat self-level a bit - it will tighten down as it dries.
What is the difference between high performance and flat out top coat?
For that reason, High Performance is the best choice for high use areas such as table tops and kitchen cabinets. Both topcoats have similar water resistance, but High Performance offers greater clarity. Use with Oil Based Finishes: Let oil-based finishes dry for 72 hours before applying High Performance or Flat Out Flat top coat.
How do you spray general finishes high performance top coat?
3:265:00How To Spray Water Based Finishes Using HVLP - The Basics - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the trigger and start spraying off the edge of the surface. Overlap each pass about 50 percent.MorePull the trigger and start spraying off the edge of the surface. Overlap each pass about 50 percent. And always keep the gun moving when the trigger is pulled.
Do you have to sand between coats of general finishes topcoat?
If a faster build is desired over raw wood, use General Finishes Sanding Sealer for the first coat, followed by 2 coats of High Performance Topcoat. Finish sand between coats with a fine-grade (220-320) sanding pad to improve smoothness and adhesion.
How do you use general finish water based top coat?
1:392:56How to Apply Water Based Topcoat - Hand Application - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour application method is we recommend three to four coats of finish. Waiting. One to two hoursMoreYour application method is we recommend three to four coats of finish. Waiting. One to two hours between coats.
How do you use general finishes gel top coat?
General Finishes Gel Topcoat Application StepsWork in a well-ventilated area. ... Stir thoroughly. ... 3 coats of topcoat are recommended. ... Wipe off the excess evenly with the grain & with light pressure using a clean cloth or high-quality absorbent paper towel.More items...
Do you have to sand before using general finishes?
The most critical part of finishing a piece of furniture happens before you open a can of stain or paint - it starts with the sanding. Sanding is critical to creating a smooth surface.
Can I use general finishes top coat over paint?
You can use GF products over wall paint, but proceed with caution. Latex wall paints are engineered for a different purpose than wood finishes.
How do you apply top coat nail polish?
To apply the top coat, begin down the center of the nail to avoid the top coat from accumulating around the cuticle area then work your up in quick strokes. Ensure that there is the right amount of top coat when you paint and be sure to remove any excess top coat before you start applying it.
How do you apply water based polyurethane without streaks?
Thin your polyurethane with paint thinner, mixing it with a paint stir stick. When polyurethane is too thick, the brush marks hold their shape and don't settle out. Thinning the product provides a smoother finished surface. Experiment with different amounts of paint thinner to see what works best for you.
How do you use topcoat?
Apply the top coat in a thin layer and seal the tip of the nail for ideal protection. Keeping it off the skin is always a win, since contact with your skin makes everything more likely to peel off. With a strong top coat, your manicure is sure to achieve peak performance.
How long between coats of General Finishes gel stain?
General Finishes recommends 6-8 hours of dry time between coats. A top coat is not necessary due to the high amount of urethane in the gel stain that will provide protection.
Can I use a gel top coat over regular polish?
The Takeaway. In short, you should not apply a gel top coat to your regular nail polish since regular nail polish has a long drying time and gel polish will trap moisture under the top coat. We recommend that you stick with a regular base coat and top coat when painting your nails with regular nail lacquer.
Do you sand gel stain before top coat?
All wood projects require preparation sanding before clear coating with a topcoat. If you skip this critical step, your finish may be rough and uneven. 1. The sanding schedule for wood that will be clear coated with an oil-based topcoat: sand up to 150-grit sandpaper.
How do you apply gel topcoat to wood?
Apply 3 thin coats of Gel Topcoat using a cloth, natural bristle brush, foam brush, staining pad, or pad applicator. The larger the surface the larger the applicator needed. Additional coats will not improve durability. Spread with a light motion, removing a small amount of the finish.
Do you sand gel stain before top coat?
Do I need to sand before applying gel stain? For previously finished wood, yes, you need to sand before applying gel stain. Generally, you need to sand enough to scuff up the existing finish and make the surface even. You DO NOT need to sand down to bare wood.
Can General finishes high performance be used on floors?
And with its pure polyurethane durability, it can even be used on floors. This is the most durable product. Colors: Water White (dries clear).
How do you apply water based varnish?
Raise the Grain First Always raise the grain on raw wood before applying a water-based finish. Simply brush, sponge or spray on some distilled water and let it dry thoroughly (overnight is best). Then, resand with your final grit paper to break off the whiskers. Now when you apply the finish, the grain will stay down.
How to apply topcoat with nylon footie?
Mix the contents thoroughly and continue to stir throughout your project. Use foam brushes and/or a pad applicator covered with a nylon footie to apply the topcoat. The footie keeps the loose fibers contained and reduces bubbles during the application.
How to sand a top coat after it's dried?
After the first layer has dried, use a 220 sanding pad to lightly sand the topcoat. This is a light buffing that will produce a light powder, indicating the finish is completely dry. When you run your hand across the surface it should feel smooth. Use an oil-free tack cloth to wipe off the powder. Make sure there is no debris left on the surface before applying the next coat.
What is the hardest polyurethane?
General Finishes High Performance Topcoat was voted the hardest, most durable consumer polyurethane topcoat by Fine Woodworking among all products tested. It is available in Flat, Satin, Semi-Gloss and Gloss.
How long does it take for a top coat to dry?
Whatever your application method, apply 3 to 4 layers of topcoat. Let each coat dry 2 to 4 hours and sand in between with a 220 sanding pad.
Can you shake water based topcoat?
Never shake water-based topcoats. Shaking creates bubbles that will mar the finish.
How long to wait before applying GF high performance?
Oil based stains must be completely dry before using a water based top coat. Wait a minimum of 48 hours before applying GF High Performance. Use a foam brush or paint pad applicator. Apply liberally using smooth, even strokes going with the grain. Use enough material to provide a wet film.
How long does polyurethane take to dry?
With its pure polyurethane durability, it's a great choice for hardwood floors. Dry Time: normally 2-4 hours under ideal conditions (70°, 70% humidity). Cooler temperatures and higher humidity will prolong drying time up to 8-10 hours. Clean up with warm, soapy water.
Is Polyacrylic Blend non-yellowing?
It is non-yellowing and offers easy water clean-up. It contains all the consumer-friendly characteristics of PolyAcrylic Blend. In addition, it contains a UV Stabilizer to protect it from breaking down in sunlight and to protect the underlying stains from fading.
How to get rid of overspray on a gun?
On large flat areas, use wet, even patterns 6 to 8 wide. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray. Overlap each pass of stain 50% for even coverage and wipe back the excess with an absorbent cloth. For narrow surfaces, reduce the fan pattern to 2-3" to reduce overspray.
What is Enduro Clear Poly?
Enduro Clear Poly is designed for professionals that routinely spray their finishes. High Performance is formulated for the retail market so it can be sprayed or hand applied.
Why does my acrylic stain blush?
The most common reason is an incompatible stain. For example, using a water-based topcoat over an oil-based based stain. When the top coat is applied , the oil in the stain seeps up through the finish and reacts with the acrylic causing a chemical blush.
How to fix espresso stain bleeding?
Allow both to dry, then apply Whitewash as a glaze (1 part stain, 1 part top coat mix). Here are two remedies we recommend to fix for bleeding that has occurred: Strip away finish and start over.
What is conversion varnish?
Conversion Varnish is a post catalyzed high solids, two component urethane formulated for professionals who need the highest level of durability and chemical resistance. Varnish will cure the fastest. Requires NCO Catalyst. It is recommended for commercial applications or extremely high-wear surfaces such as countertops and bar tops
How long does milk paint last?
Water based products do not last forever, even when unopened. General Finishes products are best used within 1-2 years. However, the life of the product may be extended with proper care and storage.
What is pre cat lacquer?
Looking for hardness, clarity and fast stack time? Pre Cat Lacquer is the choice. Use in applications where there is little risk of chemical contamination issues from substances such as ketchup, soap, chemical cleaners, or ammonia. This is the perfect spray finish for interior doors, casing, moldings, door jambs and furniture that receives light use. When you think about it, interior doors don't take a lot of wear. You might wipe them down or dust them once in a while but that is about it. PreCat Lacquer is a hard finish that provides excellent build and superior clarity at a phenomenal price point. If you are not finishing a surface such as a tabletop where you anticipate chemical contamination during use, why pay for a more expensive finish?
What is finish sanding?
Finish sanding is the process of sanding between or before the final coats of topcoat. There are several options.
How to finish a piece of furniture before painting?
1. Prep Sanding . The most critical part of finishing a piece of furniture happens before you open a can of stain or paint - it starts with the sanding. Prep sanding an existing finish further cleans the surface, removing built up dirt, grime and oil from hands. Prep sand an existing finish with a 220 sanding pad.
Why do paint cans settle?
Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older paint, use a paint mixing attachment on a drill to reincorporate the solids. If the solids dissolve and the clumps smooth out after mixing from the bottom, the product is in good condition.
How long does milk paint last?
Water based products do not last forever, even when unopened. General Finishes products are best used within 1-2 years.
Why does paint settle on the bottom of the can?
Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older paint, use a paint mixing attachment on a drill. If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use. STORAGE TIPS.
Why is there white haze on my lacquer?
White haze can develop when preparing an existing lacquer finish for re-coating. The haze needs to be removed before applying another finish.
How long does it take for oil based finishes to cure?
GF again suggests moving the piece back into warmer temperature after applying finishes for the 7 days of cure time.