The recommended procedure is as follows:
- Apply naval jelly liberally to the rusted metal with a brush, working it into crevices and pits carefully.
- Let the product work for at least 15 minutes or longer for heavy rust.
- Rinse it off with water and check for residual rust.
- Prime and paint the surface within 24 hours.
How long do you leave Naval Jelly on?
Application Instructions: Leave on 5 to 10 minutes. Caution: Wipe off painted surfaces immediately, Naval Jelly® Rust Dissolver will remove paint. The rust dissolver should not remain on a surface for more than 15 minutes. Rinse off with fresh water.
How long does it take for Naval Jelly to work?
5 to 10 minutesEasy to use, Loctite Naval Jelly Rust Dissolver can be applied on metal surfaces by brushing or spraying and works in 5 to 10 minutes for quick and convenient performance.
What is Naval Jelly good for?
Loctite Naval Jelly Rust Dissolver is the original rust treatment formula that has been used for over 40 years. It removes rust from metal surfaces such as iron, steel, and other ferrous metals while also removing bluing from steel.
How do you use naval gel?
The recommended procedure is as follows:Apply naval jelly liberally to the rusted metal with a brush, working it into crevices and pits carefully. ... Let the product work for 5 to 10 minutes, or up to 15 minutes for heavy rust. ... Rinse the area with water and check for residual rust.More items...
Can I paint after using Naval Jelly?
It can be sanded off but is okay to paint over after removing all the loose powder but it needs to be dry first. If it is still sticky the jelly still needs to dry at 60 degrees or better for a day or so.
Will Naval Jelly remove rust from concrete?
Jellied rust removers such as Naval Jelly will also remove rust stains from concrete, but there is likely to be some roughening of a smooth surface. Apply a coat of the jelly to the stain and scrub with a stiff brush until the rust dissolves or is lightened, then flush with clear water. Repeat if necessary.
What will Naval Jelly do to aluminum?
A: The Loctite Naval Jelly Rust Dissolver should only be used of ferrous metals such as steel and iron. This product will cause damage to non-ferrous metals which may not be reversible. Aluminum is a non-ferrous metal and does not rust, but it can get stained with rust from steel hardware items.
What is the strongest rust remover?
Ultimately, we selected Iron Out – Stain Remover as the best rust remover. Iron Out is simple to apply in spray-gel form, acts quickly, and for some surfaces — like rusted chrome — works to restore products to almost showroom condition. Our runner-up is CLR – Calcium Lime Rust Remover.
What does Naval Jelly do to stainless steel?
It removes rust from metal surfaces such as iron, steel and other ferrous metals and will also remove blueing from steel. Loctite® Naval Jelly Rust Dissolver® can be applied on surfaces by brushing or spraying. Removing rust from metal surfaces made of iron, steel or other ferrous materials.
Why do they call it naval jelly?
0:121:10WHAT NAVAL JELLY IS REALLY FOR! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you would do that over your rusty bits clean them up first and then go ahead and prep. Normal asMoreSo you would do that over your rusty bits clean them up first and then go ahead and prep. Normal as normal metal with primer and whatnot. So this is good stuff this one happens to be made by Loctite.
What neutralizes naval jelly?
For treatment with Naval Jelly , the pink gel is brushed on the metal surface, allowed to stay for 5-20 minutes, then rinsed off. The acids are then neutralized with a bicarbonate|baking soda paste.
Can naval jelly be used on cast iron?
Not Recommended: Naval Jelly It dries on, as you can see, and then becomes very difficult to remove. According to Nick, it can work for very small pieces of cast iron that can be fully submerged in the jelly, but most cookware is just too large.
What will naval jelly do to Chrome?
The Loctite Naval Jelly Rust Dissolver is not recommended for use on chrome because it will cause damage. This product is not a rust preventer and should not be used aluminum, chrome, stainless steel, porcelain, cement, fiberglass, marble, plastics or painted surfaces.
What does naval jelly do to stainless steel?
It removes rust from metal surfaces such as iron, steel and other ferrous metals and will also remove blueing from steel. Loctite® Naval Jelly Rust Dissolver® can be applied on surfaces by brushing or spraying. Removing rust from metal surfaces made of iron, steel or other ferrous materials.
What does naval jelly do to aluminum?
A: The Loctite Naval Jelly Rust Dissolver should only be used of ferrous metals such as steel and iron. This product will cause damage to non-ferrous metals which may not be reversible. Aluminum is a non-ferrous metal and does not rust, but it can get stained with rust from steel hardware items.
How do you neutralize naval jelly?
For treatment with Naval Jelly , the pink gel is brushed on the metal surface, allowed to stay for 5-20 minutes, then rinsed off. The acids are then neutralized with a bicarbonate|baking soda paste.
Step 1
Scrub dirt and rust encrustations off the affected metal using a wire brush. Remove as much rust as possible.
Step 2
Put on heavy-duty rubber gloves and safety goggles for protection from the naval jelly, which contains acid.
Step 3
Using a disposable paintbrush, spread the naval jelly generously onto the rusted metal. Let the naval jelly penetrate and dissolve the rust for 10 minutes. If the metal surface is heavily rusted, leave the naval jelly on for up to 20 minutes.
Step 4
Saturate a rag with water. Wipe the wet rag over the affected metal to rinse off the naval jelly.
Step 6
Examine the metal for reddish-brown spots or flakes. If rust remains on the metal, repeat the process.
How Does Naval Jelly Work
Loctite’s Naval Jelly contains around 30% phosphoric acid, which alters rust molecules and changes them into iron phosphate, which is soluble in water, making it easy to wipe off from the metal. However, due to the strong concentration of the gel, one must not allow the gel to remain on the metal for more than 15 minutes.
How to Use Naval Jelly Rust Remover
First set up the area in which you are going to work. Spread the plastic sheet on the ground to protect from the gel, and wear all your safety equipment.
What Is It?
If you really want to get technical, it is a chemical product made up of approximately 70% water and 30% phosphoric acid. Those levels are approximate because there are trace amounts of a few other things thrown in for good measure, things like sulfuric acid and a chemical called thixotropic polysaccharide.
What Does It Do?
You already know that it removes rust. That said, what can you actually use it on? Are there certain items that it shouldn’t be used on? What do you have to do in order to use it successfully? It’s not always as simple as going out, buying a product and then applying it to a surface in order to reveal some newly restored finish like magic.
How Do You Use It?
You can either spray it on or apply it with a brush. However, it’s important to know that if you are working on something with a painted surface, you shouldn’t get the naval jelly on any of the paint because it will damage it.
Use Caution
As you can probably imagine, anything that is capable of removing rust from metal can be quite harsh. As a result, you have to be very careful when you’re using it because you don’t want to cause harm to the environment or to yourself. It’s important to remember that this product is harmful to the environment.
Naval Jelly Is Sold Under the Brand Name Loctite
If you search for a rust dissolver at a hardware store, you'll come across Loctite Rust Dissolver, which is naval jelly. It contains a number of ingredients including a small amount of sulfuric acid, but its main ingredient is phosphoric acid.
How to Use Loctite Rust Dissolver
The manufacturer recommends using naval jelly at temperatures between 50 and 90 degrees Fahrenheit (10°C to 32°C). The recommended procedure is as follows:
When to Use Naval Jelly
You can use naval jelly to dissolve rust on any type of iron, steel or ferrous surface, including but not limited to:
An Alternative to Naval Jelly for Removing Rust Stains
Naval jelly is not recommended for use on nonferrous materials such as:
Features and Benefits
Loctite® Naval Jelly® Rust Dissolver is the original rust treatment formula that has been used for over 40 years.
Documents and Downloads
Sorry, Loctite® Naval Jelly® Rust Dissolver is not available online in this size through any of our connected retailers. Try selecting another size. You can also contact us .
What it is
Naval jelly is basically a gel solution that has been infused with phosphoric acid. The gel form makes it functional for removing set-in rust stains, and it retains the properties of phosphoric acid.
How it works
When placed on a rust stain, the phosphoric acid interacts with the iron oxide in rust. The interaction transforms it into iron phosphate, a substance that can be easily removed.
How to use
The Loctite products Website for naval jelly states that you can simply brush the gel on, watch the rust dissolve and rinse it off.
Benefits
Using naval jelly to remove rust can extend the life of mechanical parts. Removing rust and making regular repairs can make machines last years longer.
Dangers
As with all chemical products, be sure to wear protective clothing such as gloves and goggles when using naval jelly to decrease the risk of injury from exposure.
