4-Step Guide Of How To Use A Saunders Lumbar Traction
- Use for a specific amount of time. When you’re using it for the first time, make sure you ask your chiropractor or your...
- Lay down on the saunders device. The second step of using the Saunders lumbar traction devices to lay down on the smart...
- Us the pump to adjust the pressure. If you find that the Saunders lumbar...
What is the Saunders Lumbar traction device?
The Saunders Lumbar Traction Device is designed to provide traction (stretching) to the lumbar region (low back). The device requires minimal assembly and is ready to use out of the case. A prescription is required.
How do I Clean my Saunders Lumbar traction device?
All surfaces of your Saunders traction device may be cleaned with amild detergent or disinfectant. Do not immerse unit in water. TheSaunders Lumbar HomeTrac®Deluxe and STx®Lumbar TractionDevices should be left in the “open” position to air dry.
How do I use the Saunders lumbar hometrac deluxe?
Kneel on hands and knees in an “all fours” position, on one side of the Saunders Lumbar HomeTrac Deluxe, with your head toward the UPPER end. 2. Slowly turn your body and sit on the LOWER surface just below the lower stabilization belt. 3. Gently lower yourself so that you are lying on your side on top of the stabilization belts.
How do you use traction on a lumbar hometrac?
Applying Traction in Prone (Stomach-Lying) Position-Lumbar HomeTrac Deluxe Follow instructions for Supine (Back-Lying) Position, with the following exceptions: 1. Once you are lying on the Lumbar HomeTrac surface, place pillows under your ankles and a small towel under your head for comfort. 2.
How long does it take for lumbar traction to work?
About 20% of patients will start seeing relief of pain within the first week. Around 40% of patients will have significant relief within 2–3 weeks. The remaining 20% will get significant relief between 4–6 weeks. Less than 20% will experience no relief or minimal relief.
How do you perform lumbar traction at home?
2:005:15How to Decompress Your Lower Back at Home - YouTubeYouTubeStart of suggested clipEnd of suggested clipInto the lower back hold this for 30 seconds. If you're able to relax. And then repeat it three toMoreInto the lower back hold this for 30 seconds. If you're able to relax. And then repeat it three to five times it should help relieve a lot of pressure into the lower back so give it a try.
Which position is best for lumbar traction?
Lumbar traction in prone lying position is more effective than lumbar traction in supine lying position for the treatment of chronic lumbosacral radiculopathy.
Can traction make back pain worse?
What are the side effects of spinal traction? Spinal traction can sometimes cause pain that is worse than the original condition. Those with osteoporosis and certain types of cancer should not use traction therapy. Spinal traction is known to cause muscle spasms.
Can traction fix a bulging disc?
In conclusion, lumbar traction is both effective in improving symptoms and clinical findings in patients with lumbar disc herniation and also in decreasing the size of the herniated disc material as measured by CT.
How often should you do lumbar traction?
The treatment sessions typically last 10 to 20 minutes, and the patient can perform the procedure at home three to six times per day. Positional distraction allows frequent intermittent unloading of the effected nerve root, which is believed to have positive clinical effects.
How often should you do traction?
Duration of cervical traction can range from a few minutes to 20 to 30 min, once or twice weekly to several times per day. Anecdotal evidence suggests efficacy and safety, but there is no documentation of efficacy of cervical traction beyond short-term pain reduction.
Is traction good for your spine?
Lumbar (low back) traction helps to separate the spaces between your vertebrae, the bones that make up your spine. In theory, slightly separating these bones can help take the pressure off pinched nerves (such as the sciatic nerve) to decrease your pain and improve your mobility.
How can I put traction on my back pain?
1:326:51Traction for Low Back Pain - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf there's any muscle spasm or compression of a nerve root. It will help stretch those out so thatMoreIf there's any muscle spasm or compression of a nerve root. It will help stretch those out so that hopefully if you're having some pain down your legs or you're having pain in your bottom.
How much weight should I use for lumbar traction?
If this is your patient's first trial with traction, or if the patient's condition is irritable, it is wise to start at less than 50% of the body weight and gradually increase the force over several sessions. The patient's symptoms should always be the guide.
How do you use a traction machine?
To use an air neck traction device, place it around your neck and adjust the straps as necessary. Then, pump it up and wear it for about 20–30 minutes. Do this a few times throughout the day. You can wear the device while doing activities where you tend to slouch.
How to apply traction to a Saunders lumbar?
Once you are secure and comfortable in your Saunders Lumbar Traction Device, you will apply traction by pumping air into the cylinders using a hand pump (Figure 4).
What is a Saunders lumbar traction device?
Your new traction device is designed to provide safe and effective traction (stretching) to the lumbar region (low back).Your traction device requires minimal assembly and is nearly ready to use out of the case. Read these instructions completely before proceeding.
How to store a Saunders lumbar hometrac?
Storage Your Saunders Lumbar HomeTrac should be stored in its protective case. Replace the pump in the protective foam enclosure. Fold all belts, closing buckles where applicable.Your Saunders STx should be stored in the closed or folded position with all components stored in the storage compartment. Troubleshooting Saunders Lumbar Traction Devices feature a very accurate, sensitive gauge. The pump is speci cally designed not to leak in the “HOLD” position. If you notice a drop in the gauge reading when in the “HOLD” position it is probably because you have relaxed or moved slightly. If this happens, return to the “PUMP” position and pump back to the desired force, then reset to “HOLD”. If the traction device loses air rapidly, there may be a leak in the system. Questions to Ask: • Is the pump in the “PUMP” position when pumping? • Is the pump in the “HOLD” position when receiving treatment? • Are you lying still? (Any movement will cause ctuation). • Are you pumping slowly? • Are all the connections tight (i.e. hose cap, lens cap) If the unit is leaking air, try the following: • Check the air hose connections at the hand pump and gently tighten as necessary. Do not over-tighten as the threads may strip. • Tighten the hand pump shaft sleeve cap located above the serial number label.
How to set up a stx?
Set-up - STx Lumbar Traction Device 1. Place the STx on a rm surface. Open the closure straps that secure the STx in a closed position and lay it out at. 2. Remove the stabilization belts (2) and hand pump from the storage compartment. Place the hand pump on the oor next to the unit. 3. Attach the lower and upper stabilization belts to the lower and upper anchor hooks as shown (Figure 5). Position the belts so that their edges are overlapping. NOTE: For one-sided (unilateral) traction, the upper belt can be attached to the left or right anchor attachment as instructed by your health care provider. 4. Have a clock, timer or wrist watch available to time your treatment. Applying Traction - STx Lumbar Traction Device Positioning yourself and securing the stabilization belts on the STx Lumbar Traction Device are the same as previously described in the Applying Traction section beginning on Page 6. Go back to Section Three for operation of the hand pump.
How to use a lumbar hometrac?
Relax . . . let your traction device do the work. When the treatment is complete, release the traction by rotating the gauge housing to the “RELEASE” position. Slacken the belts, then release the buckles.You should rest and relax for a few moments before getting out of the traction device. Return the Lumbar HomeTrac to the starting position by lifting the UPPER end to a 90˚ angle and gently applying downward pressure. For the STx, lift the LOWER section. Review of Hand Pump Operation 1. “HOLD” - holds traction force at desired level. 2. “PUMP” - the cylinder with air, increasing the traction force. 3. “RELEASE” - empties air from the cylinder during or after treatment and prior to use.
What is section 2 of Lumbar HomeTrac?
SECTION TWO: SET-UP AND USE - LUMBAR HOMETRAC DELUXE
Why does my traction gauge drop?
If you notice a drop in the gauge reading when in the “HOLD” position it is probably because you have relaxed or moved slightly . If this happens, return to the “PUMP” position and pump back to the desired force, then reset to “HOLD”. If the traction device loses air rapidly, there may be a leak in the system.
Where to place Saunders lumbar traction?
Place the Saunders Lumbar Traction device in its case on a firm surface or bed with the wheels facing up.
What is lumbar traction?
The set up for lumbar traction is similar to cervical traction except that a corset, rather than a head halter, is used. Several types of lumbar traction are described including gravity inversion traction, gravity lumbar reduction and auto-traction.
How much traction is needed to separate vertebrae?
The traction load necessary to produce vertebral separation in the lumbar spine is much greater than that required to produce vertebral separation in the cervical spine. de Seze and Levernieux 167 estimated that a tractive force of 730 pounds was required to obtain a separation of 1.5 mm at the L4–5 vertebral level and that 810 pounds were required to obtain a separation of 2 mm at the L3–4 level. Numerous other studies confirm the need for great force to obtain even a small separation in the lumbar spine. 168,169 Clinically, lumbar traction functions to significantly limit the activity of the patient. It may assist to decrease muscle spasm by forcing rest. There is no evidence that lumbar traction facilitates nuclear migration of the disc.
What is positional distraction?
Positional distraction is an alternative to lumbar traction that can be performed both in the clinic and at the patient’s home. Box 4-13 shows a positional distraction demonstration. Advantages of positional distraction are that it can isolate the spinal level to maximally open the effected neuroforamen, it is inexpensive (a bolster can be made at home by tightly rolling a pillow in a sheet), and it is under the control of the patient. 126 Creighton 127 showed with radiographic evidence that positional distraction that combines isolated lumbar flexion, lateral flexion away from the targeted neuroforamen, and rotation toward the affected side focused to a spinal segment via manual therapy techniques can maximally open a targeted neuroforamen. Once the patient is placed in positional distraction, he or she should be monitored to ensure patient comfort. For the intervention to be effective, the patient should report relief of leg pain shortly after placement in the position. The treatment sessions typically last 10 to 20 minutes, and the patient can perform the procedure at home three to six times per day. Positional distraction allows frequent intermittent unloading of the effected nerve root, which is believed to have positive clinical effects. The patient gradually progresses into an exercise program as the intensity of leg symptoms subsides.
What is lumbar radiculopathy?
Lumbar Radiculopathy That Does Not Centralize (Traction) The clinical decisions of how to manage patients with leg pain that does not centralize with repeated movements and does not fit the hypomobility or instability classifications create a clinical challenge for physical therapists and physicians.
What force is used to treat lumbar radiculopathy?
Force—To effectively treat lumbar radiculopathy, herniated disk, or other conditions requiring a separation of the intervertebral space, the traction force should be great enough to cause movement at the spinal segment. Based on our experience and the evidence available in the literature, we typically use a force of 40% to 50% of the patient's ideal body weight. Often the first treatment is a little less to ensure patient tolerance.
How long does it take to traction a lumbar area?
The desired number of pounds for the lumbar area is any point between 50 to 150 lb. The desired treatment time is around 20 to 30 minutes. Comply with the instructions and progression provided by physical therapist (see Fig. 47-10).
