ZU780 Series Shark® Rotator® Pro Lift-Away® - FAQs
- Insert the wand into the nozzle then attach the pod.
- Insert wand into the pod.
- Connect handle to the wand, pressing until it clicks into place.
- Connect hose to the back of the pod, pressing until it clicks into place. For proper operation, ensure all parts are firmly clicked into place.
How do I use my shark vacuum?
0:002:27How to Use Shark DuoClean Vacuum Cleaner - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe top position is for thick carpets or rugs. Slide the surface switch to the middle for low pileMoreThe top position is for thick carpets or rugs. Slide the surface switch to the middle for low pile carpets. Slide the surface switch to the bottom.
Where do the accessories go on the shark rotator?
0:211:02How to assemble your Shark® Rotator® Lift-Away® with Self ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe lift away button then attach your accessories to the accessory holder located by the bottom sideMoreThe lift away button then attach your accessories to the accessory holder located by the bottom side of the pod. Additional accessories available at shark accessories com.
How do you adjust the suction on a shark rotator?
Adjust the amount of suction by rotating the suction release collar on the handle counterclockwise to reduce the suction or clockwise for maximum suction. The motorized brush indicator light will illuminate Green when motorized floor brush is on.
Why is the brush on vacuum not spinning shark?
Roller brush is not spinning Check to make sure the vacuum is switched to the correct mode. The switch should be in the Power and Brushroll mode to make the roller spin. If it is in just the power mode the roller will not move. The brushroll indicator light should be green when working.
Where do you store attachments on Shark vacuum?
The back of the vacuum has slots to hold up to two vacuum attachments. To store, simply place the attachment onto the circular slots.
How do you adjust the height on a Shark vacuum?
There is an adjustment piece at the top of the handle where you turn it to adjust the suction setting. This is the only way to adjust to different carpet heights and rugs. The power button is also two settings. One setting for bare floors and one for carpet.
Why is my Shark lift away so hard to push?
Suction too high If the vacuum is hard to push, the suction could be too high. Make sure the power button is on the right setting for the respective surfaces. Position I is for bare floors and position II for carpets and rugs.
Why is my vacuum so hard to push on carpet?
You Need to Change Suction Power Settings One of the most common reasons for a vacuum that's hard to push is using the incorrect suction setting. Most people want to use the maximum suction setting all the time, when in some cases this isn't necessary.
How do you lower the suction on a Shark vacuum?
0:020:26How to adjust suction control on your Shark Navigator® Zero-M™ Lift ...YouTubeStart of suggested clipEnd of suggested clipType slide to min to reduce suction and increase maneuverability on carpets slide to max to increaseMoreType slide to min to reduce suction and increase maneuverability on carpets slide to max to increase suction on bare floors.
Where is the roller brush switch on my Shark vacuum?
You can find the shark brush-bar reset button on the underside of the vacuum. What does it mean when the shark vacuum brush roll indicator light is not on? If the shark is working correctly, the lights will be green, if the roll is jammed or the shark is overheating the red light will be on.
How do you turn on the roller on a Shark vacuum?
Some Shark models are labeled as “I” or “II”, whereas others use “Carpet” or “Hard Floor” options. To make the Shark vacuum brush roll spin, you need to make sure the switch is set to “II” or “Carpet”. This starts the brush roller spinning, ready for you to clean carpets and area rugs.
Why is the brush roll not spinning?
0:071:39Vacuum Cleaner Brushroll Not Spinning - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe brush roll itself could be obstructed by hair string or lint. Clean as much debris from theMoreThe brush roll itself could be obstructed by hair string or lint. Clean as much debris from the brush roll and the brush roll housing as. Possible.
How do you store attachments on Shark rocket vacuum?
0:080:30How to store the Shark® Ultra-Light Corded Stick Vacuum - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply align the catch with a hook to store the vacuum. Then wrap the power cord from top to bottomMoreSimply align the catch with a hook to store the vacuum. Then wrap the power cord from top to bottom around the two cord hooks.
How do you put a Shark vacuum back together?
0:040:52How to assemble your Shark Navigator® Swivel Pro Complete ...YouTubeStart of suggested clipEnd of suggested clipPod. Then insert the handle into the top of the wand until it clicks into place connect the hose toMorePod. Then insert the handle into the top of the wand until it clicks into place connect the hose to the back of the pod to work properly the hose must be securely clicked into place.
How do you attach the accessory holder to Shark Navigator Lift Away?
0:221:13How to assemble the Shark Navigator® Zero-M™ Lift-Away Speed ...YouTubeStart of suggested clipEnd of suggested clipButton then attach your desired accessory to the accessory holder located by the bottom sign of theMoreButton then attach your desired accessory to the accessory holder located by the bottom sign of the pod. And connect the hose clip into the wand until it clicks into. Place you.
What attachments come with the Shark nv501?
Attachments and Accessories According to Amazon, it comes with 5 – a dusting brush, 12″ crevice tool, large turbo brush, multi-angle brush, straight suction nozzle, and the canister caddy.