How to Weave the Cane
- Start midway along the long edge of the stool and work on the top of the frame and from the center holes outwards.
- Push a piece of cane down through the center back hole (that is the side of the frame farthest away from you) and leave about 1 inch hanging down underneath.
- Wedge it in position with a peg.
How to cane a office chair?
In other words, every strand of caning material should go down through holes on the top side of the chair’s seat or the forward-facing side of the chair’s back. Make the horizontal layer. Start a second layer of cane from the center-right hole. Pass a bit of caning material through the center of the hole, then secure it with a peg.
What is chair caning or weaving?
Chair caning, rush seat weaving, and splint woven seats are all terms for specific designs and techniques used in the process of weaving a chair seat. This weaving process goes by many names, chair seat weaving, wicker, chair seating and seatweaving to name a few.
What is a hand caned chair seat?
Hand caned seats have a lacey, open weave pattern and a row of holes drilled around the perimeter of the seat and/or back. This age-old chair seat weaving method is woven by hand with individual strands of cane.
How do you sit on a chair while weaving?
I put the chair on an adjustable height table and stand on an antifatigue mat while I’m weaving. You need to make sure the chair seat is at a comfortable height so your arms don’t get tired. And using an anti-fatigue mat will save your spine and feet.
How to make a woven rail?
How to remove old cane from chair?
How long to soak chair cane in warm water?
What is a trapezoidal chair?
What is the best piece to practice with?
How to measure a cane?
How to keep your spine and feet from getting tired?
See 2 more
How long do you soak cane before weaving?
Reed and Cane need to be soaked in water for about 20 to 30 minutes before weaving. Cane Webbing and Spline need to be soaked for about 30 minutes for flexibility. If it still seems stiff, soak a bit longer. Don't try to install cane webbing if it's still dry enough to crack.
What material do you use to weave a chair?
Gather your materials Synthetic hemp rope, nylon rope, flax twine, paracord, and cotton rope are all viable options for a sturdy weave chair. On average, you'll need two lengths that are approximately 60 metres long each. But this can vary depending on the size of your chair.
How do you weave fabric for a chair?
4:217:39How to Weave a Seat for a Shaker Chair - YouTubeYouTubeStart of suggested clipEnd of suggested clipOver the first tape under the next tape. Over under and then pull it through. And it's not bruteMoreOver the first tape under the next tape. Over under and then pull it through. And it's not brute force. You're just going to tighten it up a little. And I'm going to push.
How do they make cane furniture?
Cane is first soaked in water until it attains moisture and it is weaved around the frame with thin processed cane. Different motif patterns are created while weaving. After completion of weaving, the end parts are joined with nails. Finally, the furniture is polished using natural polish.
What material is used for caning chairs?
rattan palmChair cane is made up of the stem or trunk of the rattan palm, of the genus Calamus Rotan. While there are hundreds of species of rattan, only a few are durable and beautiful enough to serve for the types of chair caning.
What is cane weaving?
To clarify, chair caning is specifically the craft of applying rattan cane or rattan peel to a piece of furniture such as the backs or seats of chairs, whereas wicker or wicker work is a reference to the craft of weaving any number of materials such as willow or rattan reeds as well as man made paper based cords.
How do you rope weave a chair?
7:3410:27How To Weave A Chair Seat With Danish Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipFrom the right to left left to right. So we're going to take the end of the cord on the spool. DoMoreFrom the right to left left to right. So we're going to take the end of the cord on the spool. Do another over under weave from the center of the chair to the front of the chair. So that the cord
What is the difference between caning and rushing?
Chairs that need pre-woven cane have a groove running around the edge of the seat. It comes in sheets that have been woven on looms and comes in a variety of weave patterns. FIBER RUSH refers to a tough grade paper fiber twisted into a long strand. It is used on square chair seats with dowel rails.
How do you weave a chair seat with webbing?
1:464:17Restore a Chair // How To Weave a Seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext is running the vertical strips that make the weave. It's pretty simple the strip's just weave.MoreNext is running the vertical strips that make the weave. It's pretty simple the strip's just weave. Over then under each horizontal strip. The hardest part is remembering to alternate.
What is woven upholstery?
Upholstery fabric can be made from any yarn or thread that is woven or knitted into a textile. Fibers such as cotton, linen, wool, hemp, polyester, polypropylene, nylon, acrylic, and rayon are strung on looms and woven, or knitted, into upholstery fabric.
How do you Shaker tape a chair?
Wrap the Tape under the front rung, positioning it at the pre-determined spot, wrap around the front rung, and take Tape toward the back of your seat. Wrap over the top of the back rung, then under the back rung. Bring Tape toward the front and under the front rung. Pull the entire length of tape through as you work.
What is chair weaving called?
Chair caning, rush seat weaving, and splint woven seats are all terms for specific designs and techniques used in the process of weaving a chair seat. This weaving process goes by many names, chair seat weaving, wicker, chair seating and seatweaving to name a few.
How do you weave wicker?
1:085:36How to make Wicker Products {www downloadshiva com} - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's important to keep moistening the rattan with hot water to keep it supple enough to manipulate.MoreIt's important to keep moistening the rattan with hot water to keep it supple enough to manipulate. They weave one thin round strand after every 13 centimeter high section of flat oval.
What is the difference between cane and wicker?
Cane is the thinner material that results from the process of stripping the rattan plant. Wicker can also be made out of rattan, but also out of bamboo, reed, willow, or even synthetic fibers. It can be made from any natural or man-made material that is durable enough to be woven.
What can I use instead of cane webbing?
A solid, fabric-covered seat is one of the sturdiest replacements for seat caning. Cut a piece of plywood to fit over the seat frame, then cover it with cushion foam, batting and durable upholstery fabric stapled to the bottom of the plywood. Screw the new seat to the chair frame from below.
How much does it cost to re cane a chair?
Labor: $1.40/per drilled hole, plus materials ($20-$40). More than 72 holes: $1.45/per drilled hole, plus materials. Holes are drilled around the perimeter of chair seat frame and individual strands of cane are hand woven through the series of drilled holes.
Can you glue cane webbing to wood?
To attach the cane to the back of the frames, I used a wooden trim cut to the same size as my frame. First I cut the cane to size, then glued the cane to the frame with wood glue and then sandwiched the cane between the frame and the trim, using some short screws to keep it all in place.
Is caning a chair difficult?
Caning a chair is a fun and easy project. Just get a cane-ready chair and measure the holes to determine what sort of gauge you need. Thread the cane through the chair from the center to the right side, then from the center to the left. Finish up by weaving the cane from the back edge to the front.
How do you Recane a chair back?
Place the trimmed cane webbing over the back of the chair and align so that it is straight and covers the groove in the chair back by at least a half inch. Use the wedges, or spatulas, to push the cane webbing in part way. Don't be too aggressive, you don't want the cane to break.
Are cane chairs durable?
Made from cheap and weather-resistant plants, trees, and grasses like rattan and willow, wicker gained popularity for its durability and flexibility (fun, rounded chairs!
How do you weave a chair seat with webbing?
1:464:17Restore a Chair // How To Weave a Seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext is running the vertical strips that make the weave. It's pretty simple the strip's just weave.MoreNext is running the vertical strips that make the weave. It's pretty simple the strip's just weave. Over then under each horizontal strip. The hardest part is remembering to alternate.
How do you weave a wicker chair seat?
7:2714:04How to Cane a Chair | Weaving a Caned Chair Seat - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe very first set of strands. That you put down and then over the most recent set of strands. AsMoreThe very first set of strands. That you put down and then over the most recent set of strands. As you go across the step 4 cane will need to sit below.
How do you weave a round chair seat?
1:531:11:35How to Weave a Round Laced Cane Chair - YouTubeYouTubeStart of suggested clipEnd of suggested clipMove the peg. Come up to the hole next to the second row in the back i'm guiding it underneath toMoreMove the peg. Come up to the hole next to the second row in the back i'm guiding it underneath to make sure that it doesn't twist. You're not ever weaving under the chair seat. It's very intentional.
How do you weave a chair seat with reeds?
1:0422:36How to Weave a Splint Seat in Herringbone Pattern Using Flat ReedYouTubeStart of suggested clipEnd of suggested clipAnd then over the back rail. And I'm going to go ahead and run this piece. All the way until there'sMoreAnd then over the back rail. And I'm going to go ahead and run this piece. All the way until there's nothing left and then I'll go back and position it and tighten it up.
Chair Caning Instructions–How-To Weave A Lace Cane Seat
Copyright © 2007 The Wicker Woman®–Cathryn PetersDifficulty Level: Moderately Challenging InstructionsThings you’ll need for this caning project: 1...
Chair Preparation Before Starting Chair Caning Instructions
(Click step photos below to enlarge) For your first attempt, find a chair that is sound and not in need of refinishing or regluing, with holes dril...
Determine Correct Size Chair Cane to Weave Your Seat
To make sure you are using the correct gauge or size of strand chair cane for this project, you will need to measure the diameter of the drilled ho...
Ordering Correct Gauge Chair Cane
Once you have determined the correct size cane to use for your project, you can purchase the cane and binder cane from the cane and basket supply c...
Assemble All Necessary Tools For Chair Caning
Most of the tools you’ll need to use weaving your cane seats are minimal and you probably already have several of them laying around the house or i...
Step #1 of #7 — Laying The Vertical Cane Strands
Remove a few strands of chair cane from the hank and loosely coil them in a dishpan of warm water to soak for about ten minutes. Periodically repla...
Step #2 of #7 — Laying First Horizontal Cane Strands
Now continue laying the horizontal strands from side to side, on TOP of, or OVER STEP #1 that you just put in. Add new strands justas you did befor...
Step #3 of #7 — Laying Second Verticals Cane Strands
With this step, begin laying the second vertical strands front to back, OVER the top of STEPS #1 & #2, and just slightly to the RIGHT of STEP #1, t...
Step #4 of #7 — First Actual Weaving-Second Horizontal Cane Strands
The real weaving begins with the second side- to-side course, horizontally alternating under-over weave through the doubled front-and- back course....
Step #5 of #7 — Weaving The First Diagonal Cane Strands
Start the first diagonal course in the front left-hand corner of the chair. This step will be weaving ALL the diagonal strands and will slant from...
How to make a woven rail?
Begin by securing the front rail binder cord in the left corner hole with a peg. Then using a long length of weaving cane, put one end down the backside of the next hole to the right of the corner. Loop the long end of the weaver, over the binder cord and down into the front side of the same hole.
How to remove old cane from chair?
If there is old cane is in the seat, you will have to remove it using scissors and/or a utility knife or box cutter. Start your caning project with a good, sound chair with drilled holes totally clear of old cane. To remove cane strands, cut loops on bottom of chair frame, pull out from top.
How long to soak chair cane in warm water?
Remove a few strands of chair cane from the hank and loosely coil them in a dishpan of warm water to soak for about ten minutes.
What is a trapezoidal chair?
trapezoidal shape (wider in front than in back) chair with straight seat rails and pre-drilled holes around the perimeter of wooden frame seat
What is the best piece to practice with?
Your best first practice piece would be a square or rectangle footstool. Or if you can’t find one of those, a trapezoidal shape chair (wider in the front than the back), with fewer than 72 drilled holes is the next best thing.
How to measure a cane?
Measure center-hole-to-center-hole and diameter of holes to get the correct size of cane.
How to keep your spine and feet from getting tired?
You need to make sure the chair seat is at a comfortable height so your arms don’t get tired. And using an anti-fatigue mat will save your spine and feet .
How to get loose end of caning material taut?
Bring the loose end up through the hole to the right. Place a peg in the hole to keep the caning material taut. Pull the loose end across the opening to the hole on the opposite end.
How to secure a caning peg?
Slip a piece of caning material into the center rear hole. Allow about 2 inches (5.1 cm) of the caning material to dangle through the bottom of the hole. Jam a peg into the back rear hole to secure it using your fingers. Pull it taut and push the other end through the front-center hole, then secure it with a peg.
How to keep cane weave from coming loose?
When you’re done, look beneath the chair and tie any loose strands you see to the nearest vertical strand. Loop the loose strands around the nearest vertical strands once or twice, then pull the rest of the loose strand through the loop. This will prevent the cane weave from coming loose.
How to make a chair with cane?
Make the horizontal layer. Start a second layer of cane from the center-right hole. Pass a bit of caning material through the center of the hole, then secure it with a peg. Pull the other end across the chair and pass it through the hole directly opposite.
How to add a new strand to a caning?
Add a new strand by sliding it through a hole and securing it with a peg. Adding new strands requires the same basic technique you used when inserting the initial strand. Leave a bit of the caning material loose and dangling through the hole.
What happens if the eye of a cane is not smooth?
If the “eye” of the cane is not smooth or has a break in it, the caning material will be weaker and might snap under pressure.
How to measure caning material?
Determine the gauge of caning material you need. To determine the gauge of caning material you need, use a ruler to measure the distance between the holes (center to center) and the diameter of each hole. The larger the hole, the larger the gauge of cane you’ll need to order.
What is chair caning?
However, most people lump it all together including the woven seat pattern and material, and the act of weaving itself, so it all becomes “chair caning.”. Actually, the term “chair seat weaving” encompasses many different types of weaving techniques, patterns, designs, and weaving materials. With chair caning itself being only one type ...
How many steps are there in caning a chair?
Many different gauges of cane are used to suit the design of the chair and size of the drilled holes, but all woven in the same 7-step pattern. The 7-step method of hand chair caning is tedious and time-consuming to weave, but a lovely, strong, and durable pattern when completed. There are also many other designs that can be woven through ...
What is a caned chair?
Hole-to-Hole Chair Caning –is the traditional and most well-known of the seat weaving designs and patterns. Hand caned seats have a lacey, open weave pattern and a row of holes drilled around the perimeter of the seat and/or back.
What material is used for Danish chairs?
Another material frequently used in weaving Danish Modern chair seats is wide binding cane in either 4, 5 or 6 MM. Cane is woven on both the seat and back, in various patterns but only around the frame and not through drilled holes or put in a groove.
What is Danish modern seat weaving?
Danish Modern Seatweaving –typically uses a 2-ply laced Danish cord and is looped around “L” shaped nails on the inner framework, woven in a special basket weave design.
What is a paper rush chair?
Paper rush is frequently used to weave seats on Colonial style, mule-ear style, and other post and rail modern chair seats, and also was used in weaving wicker furniture from the 1910s-1940s .
What is chair seat weaving?
Chair caning, rush seat weaving, and splint woven seats are all terms for specific designs and techniques used in the process of weaving a chair seat. This weaving process goes by many names, chair seat weaving, wicker, chair seating and seatweaving to name a few. However, most people lump it all together ...
How to make a woven rail?
Begin by securing the front rail binder cord in the left corner hole with a peg. Then using a long length of weaving cane, put one end down the backside of the next hole to the right of the corner. Loop the long end of the weaver, over the binder cord and down into the front side of the same hole.
How to remove old cane from chair?
If there is old cane is in the seat, you will have to remove it using scissors and/or a utility knife or box cutter. Start your caning project with a good, sound chair with drilled holes totally clear of old cane. To remove cane strands, cut loops on bottom of chair frame, pull out from top.
How long to soak chair cane in warm water?
Remove a few strands of chair cane from the hank and loosely coil them in a dishpan of warm water to soak for about ten minutes.
What is a trapezoidal chair?
trapezoidal shape (wider in front than in back) chair with straight seat rails and pre-drilled holes around the perimeter of wooden frame seat
What is the best piece to practice with?
Your best first practice piece would be a square or rectangle footstool. Or if you can’t find one of those, a trapezoidal shape chair (wider in the front than the back), with fewer than 72 drilled holes is the next best thing.
How to measure a cane?
Measure center-hole-to-center-hole and diameter of holes to get the correct size of cane.
How to keep your spine and feet from getting tired?
You need to make sure the chair seat is at a comfortable height so your arms don’t get tired. And using an anti-fatigue mat will save your spine and feet .
