- Step One: Open the Clock Face. Try to wind the clock as close to the time when it stopped as possible. ...
- Step Two: Locate the Clock Key. They are usually hung in the back of the clock, or on the inside of the case where the pendulum is. ...
- Step Three: Place the Clock Key Into the Right Side Winding Hole. Turn the key counterclockwise until you meet resistance. ...
- Step Four: Listen For the Correct Sound. Swing the pendulum to start the clock. There should be no pauses between each "ticktock" second of the clock.
- Step Five: Inspect the Clock One Week After Winding. If the time is too fast or too slow, you can adjust how fast the pendulum swings. ...
How do clock regulators work?
Regulators are set by increasing or decreasing the speed of the pendulum swing. 1. Synchronize the regulator clock to a known accurate time source such as the time displayed on a cellphone or computer.
What is a regulator clock?
A regulator clock is a generic term for a wall-mounted, weight-driven clock regulated by a swinging pendulum. Invented in the late 18th century to improve upon the accuracy of spring-wound clocks, regulators usually have separate mechanisms for the minute and hour hands. Once the design was standardized in Vienna, ...
How long to wait to check time on regulator clock?
Wait 24 hours, then compare the time on the regulator clock to the time displayed by an accurate time source to determine any discrepancy in the clock’s accuracy.
How to increase the speed of a pendulum?
Rotate the pendulum adjustment nut c lockwise to accelerate the pendulum swing and increase the speed of the clock. Rotate the pendulum adjustment nut counter-clockwise to slow the pendulum swing and the speed of the clock. Each 360-degree rotation of the nut alters the speed of the clock by 30 seconds per 24-hour period.
How to wind a clock with a key?
The most effective way to wind your clock would be to open the front door, insert the crank, hold the clock steady with your left hand, and turn the crank with your right hand.
How to wind a British clock?
Although British dial clocks are meant to be wound using a key, using a crank is much easier. To wind the clock simply place the key, or crank, into the winding point and turn clockwise sixteen revolutions. When the clock is fully wound an internal mechanism will prevent you from winding any further. You should be able to turn the key ...
How to wind a clock in silent mode?
The lower the weight hangs, the closer it is to the end of the cycle. To wind, simply insert the crank into the winding points turning clockwise approximately thirteen revolutions. As you turn the crank you should see the weight rise.
Why do clocks have three winding points?
The reason clocks have multiple gear sets is so a clock can chime on the hour and quarter hour while it keeps time. All clocks require at least one set of gears dedicated to keeping time.
What is a British dial clock?
WINDING AN ANTIQUE BRITISH DIAL CLOCK. British dial clocks are time-only spring driven clocks. They typically have one set of gears with one winding point. A clock with only one set of gears is correctly referred to as a timepiece. Timepieces only keep time; they don't chime on the hour or quarter hour. To be called a clock, a devise must both keep ...
How to set time on a clock?
After winding the clock, set the correct time by moving the minute hand either clockwise or counterclockwise. If the clock is running too fast, or too slow, adjust the nut on the bottom of the pendulum rod.
How many winding points does a clock have?
This is because there are different types of clocks and some can have more than one winding point. Most clocks will have one, two, or three winding points. Some clocks are wound using a key or crank, while others are wound by pulling on a chain.
How long should you wind a clock?
Wind the clock at approximately the same time of day each time. You also should never wind a clock within 10 minutes of a chime or strike, as this period is when gears and levers fall into position.
How Do You Wind a Mantel Clock?
Many timepieces in the Chelsea mantel clock collection have a mechanical movement. This clock technology dates back to 1300 and is still popular among those who prefer vintage timekeeping. Mechanical mantel clocks need to be wound regularly, or else all they are is a pretty-looking statue on a shelf.
How to stop a Chelsea clock from striking?
Striking clocks are shipped from the factory with a “stop-tube” places in one of their winding arbors. This tube stops the clock from running keeping it from striking during shipping, as well as preventing the strike mechanism from jamming when the clock fully winds down. We recommend that you keep this “stop-tube” in a safe place and place it in the clock when you will be away traveling and unable to wind the clock.
How to make a clock run faster?
Moving the regulator towards the F will make the clock run faster, and towards the S will make the clock run slower. Just the very slightest adjustment of the regulator can go a long way. Allow the clock to run for a full week, observing it’s timekeeping before making additional adjustments.
How to unjam a clock?
Unjamming the strike mechanism is quite easy. Gently move the minute hand of your clock counterclockwise by a few minutes. You will likely hear the clock strike, and the mechanism has released. You can then proceed to wind and set your clock as your normally would.
What era was the mechanical clock invented?
Mechanical clocks trace their roots back to the Renaissance era, and are still popular today among those who are intrigued by the allure of mechanical timekeeping. These clocks require weekly winding and setting, and the tradition of this act often grows to be something that clock enthusiasts really look forward to.
What time zone do Chelsea clocks go in?
All Chelsea clocks are fully wound and set to the Eastern time zone before we ship them. If you have a vintage clock or live in another time zone, you will need to set the time. To do this, gently and slowly move the minute hand in a clockwise direction.
Why did railroads use regulators?
Railroad employees would synchronize their pocket watches to these regulator clocks several times a day. This helped to reduce the number of train collisions.
Where is Gregg Perry's clock studio?
We turned your question over to one of the world’s leading clock experts, Phil. Gregg Perry operates a studio in Pennsylvania (perrysclocks.com) specializing in the conservation and restoration of antique clocks and watches. He’s also a certified appraiser of these timekeepers. Here’s what we learned from Gregg:
How to wind a grandfather clock?
To wind this kind of clock, simply pull down on the chains until the weights reach the underside of the wooden board at the top of their trajectory.
How to turn a clock clockwise?
Insert the key or crank into a winding point. Hold the clock steady with your nondominant hand and use your other hand to turn the key or crank clockwise. If it won't turn clockwise, your clock winds counterclockwise, so turn the key or crank the other way.
How does a pendulum clock work?
Unlike modern electric clocks, pendulum clocks keep time using a series of spring-loaded gears that require regular winding, usually once a week . A special clock key or clock-winding crank turns the mechanism. If you've lost the key or crank that originally came with the clock, replace it with a new one from a clock repair shop.
How many winding points does a clock have?
Each winding point operates a particular set of gears. According to Tick Tock Tony, the clock will have at least one and up to three winding points: one for keeping time and perhaps one for chiming on the hour and one for chiming on the quarter-hour. Insert the key or crank into a winding point.
What is a pendulum clock?
Pendulum clocks bring an air of elegance and classic finery to wherever you place them. Small pendulum clocks are traditional decoration for mantels, and large grandfather clocks often stand in entryways, halls and odd corners of period homes. Unlike modern electric clocks, pendulum clocks keep time using a series of spring-loaded gears ...
Can you force a key to turn in either direction?
Don't try to force the key or crank if it doesn't turn easily in either direction, as this can damage the clock. Have a specialist look at the mechanism and make any necessary repairs.
How to wind a quarter hour clock?
Insert the winding key into one of the three holes until it s fully seated. The arbor to the right of centre winds the quarter hour chimes and the left of centre arbor winds the hour counting strike. Clocks with three winding arbours chime on the quarter hour making a musical tone.
How many winding holes are there on a clock?
Turn the key to determine the correct winding direction of the arbor. Clocks that require actual winding will have anywhere from one to three winding holes on the body of the clock often in the back facing.
Where are the pegs on a clock?
The winding pegs for antique or reproduction clocks are typically square and found in a small hole on the face side or rear of the clock depending upon its make. Howard miller zeeland michigan west germany mechanism triple chime key wind mantel clock mod 620 132.
How many holes are there in a chiming clock?
Three winding holes this is a chiming clock. You might also see a smaller hole on the clock face usually located at the 12 o clock position.
Video
This clock was my paternal grandmother's which hung in the living room. It has been sitting in the basement collecting dust. A great memory of my grandma.
Latest News
Around 3:30 a.m. on July 11, as he and several other Scranton police officers searched for a trio of young armed robbery suspects who scattered after crashing a stolen SUV in West Scranton, Patrolman Wilding hopped over a low wall at the edge of a ...
More news
Comes with wind up key. No marks except minor marks where the key goes in ... Thanks for bringing this to my attention. The clock is in perfect working condition.
How to wind a clock with a key?
If the dial is covered by a glass door, open it to access the face. Insert the key into one of the winding arbours and with your non-dominant hand, steady the case while you wind the clock. I recommend wearing cotton gloves to preserve the finish of the case.
Where is the regulating arbour located on a clock?
If you have a double-ended key the small end fits that arbour. Some clocks will have the regulating arbour located under the centre cannon where the hands are attached. Double-ended Key.
What is the arbour on a clock?
On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o’clock position. It is also an arbour but a smaller one used for regulating the speed of your clock.
Why do clocks have two ends?
Two ends are required because the speed adjustment arbour is smaller than the winding key arbour.
How many half turns does an 8 day clock need?
An 8-day clock usually requires 14 half turns of the key as the arbour does one complete turn per day. Mainspring ratchet and click. The ratchet locks the spring in place during each wind of the key. Allow the key to gently rest back onto its click.
What is a winding arbour?
Each winding arbour has a function. The number of winding arbours corresponds to the number of gear trains (or sets of gears) on a clock. For example, if there is one hole it is a time-only clock; 2 holes mean that it is a time and strike clock, that is, it strikes the appropriate hour on ...
What is the arrow on a Seth Thomas mantel clock?
On this spring-driven Seth Thomas mantel clock (next photo) the left arbour (arrow) winds the strike side and the right arbour (arrow) winds the time side. The smaller hole just below the centre cannon is for regulating the clock.
