6 Simple Steps on Winding a Worx Trimmer Line:
- Step 1: Pressing the release tabs First of all, find out the release tabs of the trimmer that hold the spool in position. ...
- Step 2: Pulling the spool ...
- Step 3: Dividing the strings ...
- Step 4: Feeding the strings ...
- Step 5: Placing the second string: ...
- Step 6: Sliding the spool back to the shaft ...
How do you wind a new line on a strimmer?
1:333:11Replace the line in your string trimmer! - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf your trimmer head has two lines you will need to take two equal lengths of line insert them intoMoreIf your trimmer head has two lines you will need to take two equal lengths of line insert them into the holes. And wind them in the direction that the arrow indicates.
How do you load a strimmer line?
0:071:38How to Load a Flymo Trimmer line in a Flymo Trimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe top deck first you'll need to push some of the line in to get some purchase a couple ofMoreThe top deck first you'll need to push some of the line in to get some purchase a couple of centimetres should do it and then start winding it neatly in the direction of the arrow.
How do you put strimmer wire on a petrol strimmer?
0:522:16How To Replace The Strimmer Line On An SGS Strimmer - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet your new strimmer line and place it within the hole here and feed it through to the oppositeMoreGet your new strimmer line and place it within the hole here and feed it through to the opposite side of the spool measure halfway and bring the line through so each side has half and half.
How does a bump feed work on a strimmer?
0:140:46RYOBI: What is a 'bump feed' trimming line head? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWithout having to turn the Machine off the bump head is tapped on the ground while spinning. And theMoreWithout having to turn the Machine off the bump head is tapped on the ground while spinning. And the centrifugal force releases. Short lengths of line at a time.
How do you load a brush cutter?
Hold your brush cutter with the blade 2-8” above the ground. Start the cutter and bring the left side of the blade against the right side of the tree. Let the left side of the limit stop deflector rest against the tree to help hold the brush cutter in place.
How do you load a Black and Decker strimmer line?
0:091:18Changing a Single Line Spool on a BLACK+DECKER String TrimmerYouTubeStart of suggested clipEnd of suggested clipHold the string tightly to make sure it doesn't unravel during this step take the new spool and pushMoreHold the string tightly to make sure it doesn't unravel during this step take the new spool and push it onto the boss on the housing rotate. The spool slightly. Until it is seated.
Why is it important to rewind a string trimmer?
It's important to rewind or wind a string trimmer correctly to prevent injury and make sure the machine continues to work properly.
How to cut a piece of string?
Use a pair of sharp scissors to cut a piece of string 9 feet long. If your manual says you have a double string model, then you'll need to cut two pieces. Make sure you use the sharpest scissors possible. Dull scissors will fray the edges of the string, making it harder to insert back into the retainer and wind smoothly.
Can you take the string out of a trimmer?
Depending on the model, you can take the entire spool out of the retainer and then remove the old string. Other models will have the spool attached to the trimmer, meaning you'll need to pull the string out of the spool as it remains in the retainer.
How to properly wind the line around the trimmer spool?
This is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.
Where is the end of a trimmer reel inserted?
The end of the line is inserted into the head into a special technological groove or hole , and the winding is done in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.
Why does my reel fly out of the reel?
In a rush, some people do not follow the threading grooves inside the spool and wind the thread randomly. This will cause the line to fly out of the reel and may even cripple.
What is needed before winding a car?
Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:
What is a trimmer used for?
The trimmer is useful for trimming small or difficult areas, such as near hedges, between beds and along paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any owner’s request.
What does winding a thread in the opposite direction mean?
Wind the thread in the opposite direction to the marks on the body. They indicate the direction of movement of the head.
How much line do you need to replace thread?
In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself.
How to wind a string trimmer?
Absent any other indication of which direction to wind a string trimmer spool, physics tells you to wind in the direction opposite to that of rotation. If the head spins clockwise, wind the string counterclockwise and vice versa. If you do this, the force of the string striking whatever it's cutting will tighten it and pull it out of the head. If you wind the string the other way, the cutting force will loosen it and push it back into the head, and it may disappear altogether.
What happens if you wind a string the other way?
If you wind the string the other way, the cutting force will loosen it and push it back into the head, and it may disappear altogether. A simple observation will tell you what direction the head rotates, but it's hard to maintain the orientation when you turn the trimmer over and remove the spool from the head.
Why Are There Different Directions?
If the world was a perfect place, all string trimmer heads would rotate in the same direction, just as all bolts would have the same type of head, and all cars would have the same size tires. In the real world, some string trimmer heads rotate clockwise and some counterclockwise, and it depends on what the trimmer is designed to cut, whether the trimmer has a straight or curved shaft and, to a lesser extent, whether the trimmer is gas or electric.
Which way should a trimmer head be wound?
Wind the string in the opposite direction, because if you don't, it will have a tendency to unwind as you're operating the trimmer. Many trimmer heads spin clockwise and should be wound counterclockwise.
Does a string trimmer have an arrow?
If you come across a string trimmer – Weed Eater or otherwise – that doesn't have an arrow on the trimmer head, trust physics and wind in the direction opposite the spin. That way, you'll be sure that the string will feed out as you're working rather than slipping back inside the trimmer head.
Is a weed eater a string trimmer?
All Weed Eaters are string trimmers, but not all string trimmers are Weed Eaters because Weed Eater is a brand name. Weed Eater shares the string trimmer market with numerous other manufacturers, including Husqvarna, Echo and STIHL (to name a few), and just as the best trimmer line for STIHL isn't the best for Weed Eater or any other brand, ...
How to keep trimmer line from jamming?
Locate the starter hole in the spool . Insert the tip of the trimmer line, and wind in the direction of the arrows. Wrap the line in neat, straight rows, to prevent jams later on. When there are about 5” or 6” of line remaining, snap it into the retainer on the spool to hold it in place.
How to tie trimmer line to spool?
Locate the starter holes in the spool. Insert the tip of the first length of trimmer line into one starter hole, and wind in the direction of the arrows. Wrap the line in neat, straight rows, to prevent jams later on. When there are about 5” or 6” of line remaining, snap it into the retainer on the spool to hold it in place. Repeat this process with the second line. At this point, the line ends should be at opposite sides of the spool, to match the eyelets on the outside of the tri mmer head.
How to replace a retaining cap on a spool?
Line up the retainer with the slot on the outside of the head. Replace the spool into the trimmer head. Remove the line from the retainer, and pull it through the slot to make sure it is feeding smoothly. Reattach the retaining cap.
How many halves does a double line trimmer have?
Double-line trimmers typically divide the spool into two halves (one fore each protruding line).
What happens if you buy the wrong width of line?
The length and width of line you need varies based on your trimmer. If you purchase the wrong width of line, the trimmer will not work correctly, so don’t waste your money by simply guessing at the hardware store.
How to remove retaining cap on a trimmer?
Remove the retaining cap from the trimmer head. This will probably involve either unscrewing it, pressing one or multiple tabs, or a combination of the two. Some models use different mechanisms for removing the spool. These should be designed to be relatively intuitive, but contact your trimmer’s manufacturer if you are having trouble figuring it out.
How long should a trimmer line be?
If you are not sure what size line your trimmer uses, check online—the manufacturer’s website often has instructions, and if not the customer service department should be able to help you.The length to which the line should be cut also varies, from around 10’ to 25’.
How does a Worx string trimmer work?
A Worx string trimmer is operated by a battery. It needs a standard spool along with a double string trimmer line to efficiently work. Over time, it needs to feed new strings as it works with a bump-feed system. Simply hit the trimmed head upon the ground in order to feed new string to your string trimmer.
How to discard strings from a trimmer head?
Drag the spool of the trimmer head in order to discard the remaining strings from the spool.
Why does my string trimmer break?
A string trimmer has to deal with various harsh surfaces when weeding out the garden. In general, the trimmer line breaks more frequently when you do use the trimmer on thick grass patches, rocky surfaces, wet grounds, or other rough surfaces. If the trimmer head gets hit in a wall, garden stone, paving edge, or something like that, the trimmer line can break.
Why won't my Worx trimmer work?
The Worx trimmer can’t work for several reasons. When the replacement battery is not placed correctly, your trimmer won’t work well. You should replace the charging station as soon as possible. First, plug the battery into the trimmer. Then tab the lock button. After that, press the trigger button. If you notice that the lock button is not working, you need to replace the lock button immediately. Plus, the Worx trimmer can stop working when you use it for weeding out rough surfaces frequently.
Where are the release tabs on a spool trimmer?
Keep an eye at the edge of the trimmer shaft where you’ll get the trimmer head. The releasing tabs are placed on the side of the head. After finding it, press the release tabs.
Is a string trimmer useful?
Being a gardener, a dedicated string trimmer is one of my most useful tools. A couple of weeks ago while I was using the string trimmer, it wasn’t functioning well. Then, I realized I needed to feed a new string to my Worx trimmer.
Can you wind a string trimmer without feeding new strings?
Without feeding new strings, the string trimmer won’t work properly. Thus, winding the trimmer line is even more important. That’s why we have discussed here the steps on how to wind Worx trimmer line. Do follow them:
How to wind a string in a spool?
Insert the end of one of the lengths of string into the upper anchor hole in the hub of the spool and wind the string in the direction of the arrow on the base of the spool. Keep the string confined to the upper section of the spool and stop winding when about 6 inches of string remains.
How to turn a string head?
Hold the string head with one hand while you unscrew the spool retainer with the other. You may have to turn the head clockwise or counterclockwise; some heads have reverse threads while others don't.
How to make a spool of arrows?
Cut a single 9-foot length of 0.065-inch microfilament string from a roll. Feed one end into the hole in the center of the spool and wind the string in the direction of the arrow. Stop winding when 6 inches of string are left on the end.
How to clean a spool on a spool?
Remove the spool, ensuring that the spring remains attached to it. Pull off any old string and clean the spool and the inside of the head with a rag.
How to replace a spool retainer?
Replace the spool retainer by aligning the tabs and pushing down until they lock. In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer.
What is Ryobi string trimmer?
Ryobi manufactures a number of gasoline-powered string trimmers, as well as a battery-powered model that is part of its One+ line of tools that operate on a common lithium-ion battery-pack. The string heads for the gasoline- and battery-powered models aren't the same. The most important difference is that the latter takes only a single 0.065-inch string while the former takes two strings that can be from 0.080 to 0.095 inches in diameter. The procedures for winding the heads are similar and shouldn't delay your trimming job for longer than about 10 minutes.
How much space between wound string and spool?
In order to avoid overfilling the spool, ensure that there is 1/4 inch of space between the wound string and the outside edge of the spool. Avoid using string that is too wide for your trimmer. It won't advance properly, and you could overwork the trimmer engine and burn it out.
Which way to wind a spool?
Follow the arrows on the side of the spool for the best results when winding the spool. Typically this is counter-clockwise.
How to replace a power trimmer?
To safely replace the line on your power trimmer, it's important that it doesn't turn on while you work on it. Unplug the trimmer or remove the ion battery that came with it . This will ensure that you won't accidentally turn on the trimmer and injure yourself.
How to lace a spool on a spool trimmer?
Lace the line through the eyelets on the cap. Pull the excess line out of the eyelets on the spool and push them into the eyelets on the cap. Your spool is now ready to go back into your trimmer.
How to secure a spool?
Set the spool into the cap. Make sure that the eyelets on the cap and the spool are also lined up. Line up the hole in the center of the spool with the center of the cap and gently press the spool back into the cap. Once you hear a click, turn the cap over and shake it to make sure that the spool is secure.
How to remove a trimmer cap?
To remove this, use your fingers to press in the tabs that are on both sides of the cap. Once the tabs are pressed, simply lift up on the trimmer cap to remove it and expose the spool underneath. Pull the spool from the cap. Turn over your cap to reveal the line and spool.
How to secure a spool of spooling thread?
Secure the line to the spool and cut the line. Allow for 6 inches (15.24 cm) of slack on the end of your line after you're done wrapping it around the spool. Cut the thread with gardening shears or sharp scissors and put the excess line through the eyelets on the spool to hold them in place.
How to remove old string from a spool?
Remove the old line from the spool. To remove the old line, lift it from the eyelets that hold it in place and pull the free end of the line. This will result in removing the old string. Repeat the process on the other side of the spool to remove all of the old lines. Wear gloves when working with your trimmer.
