Knowledge Builders

how do you wind ansonia mantel clock

by Dr. Felicity Nicolas III Published 1 year ago Updated 1 year ago
image

How do you wind Ansonia mantel clock? To wind the clock simply place the key, or crank, into the winding point and turn clockwise sixteen revolutions. When the clock is fully wound an internal mechanism will prevent you from winding any further.

Part of a video titled HOW TO WIND UP A MECHANICAL CLOCK - YouTube
2:03
12:24
It's going counterclockwise.MoreIt's going counterclockwise.

Full Answer

Where can I find the model of my Ansonia Clock?

Your clock model is the "Ranger" which appeared in an Ansonia catalogue in 1886. It is shown on page 453 in Tran Duy Ly's Ansonia Clocks and Watches.

How to identify antique mantel clocks?

Terry’s former partner Seth Thomas also joined the trend creating the common “Black Mantel Clock.” A quick way to identify antique mantel clocks is by understanding the different types. Long before manufacturers started leaving signatures on their products, they had unique styles.

How do you wind a clock with 3 arbours?

Clocks with three winding arbours chime on the quarter-hour making a musical tone. On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o’clock position.

Which way do you turn a clock to wind it?

I recommend wearing cotton gloves to preserve the finish of the case. Next, turn the key clockwise. If it will not turn clockwise, turn counterclockwise. Yes, some clocks wind clockwise and some counterclockwise. Do not force the key; wind it with minimal force and wind the arbour until it winds no further.

image

How do you wind an Ansonia mantle clock?

0:093:43Ansonia mantle striking clock with no self correcting mechanism - setting upYouTubeStart of suggested clipEnd of suggested clipSo you wind up the springs until they come up tight. You know the pendulum headings on a hook. ButMoreSo you wind up the springs until they come up tight. You know the pendulum headings on a hook. But she'll feel if you just gently put your fingers in underneath the door here.

How do you wind a mantle clock?

Unjamming the strike mechanism is quite easy. Gently move the minute hand of your clock counterclockwise by a few minutes. You will likely hear the clock strike, and the mechanism has released. You can then proceed to wind and set your clock as your normally would.

How do you wind a clock with two holes?

If there are two holes, one is for the time spring and one is for the hourly chime. Some clocks also have a third hole, which governs the quarter-hour chime tones. Movement length should be specified by the manufacturer in the original packaging when you buy the clock.

How do you wind a session on an antique mantel clock?

0:475:23Winding The Sessions Mantle Clock + Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou would insert your key in here. And turn it ever so slightly not like ever so sloppy a bit likeMoreYou would insert your key in here. And turn it ever so slightly not like ever so sloppy a bit like you know a little about a quarter of a turn maximum. Then wait 24 hours and check the time.

What are the three winders on a mantel clock?

The center winder is for the timekeeping, the right winder is for the quarter-hour chime, and the left winder is for the hour strike.

How do you set an old mantle clock?

Mantel Clock Setup: Place clock on table with back facing you. Open the back door, hang the pendulum on the hook, and close the door. Carefully place the clock where it is to be used, on a stable, level surface. Lift one side of the clock gently two inches, then put it down to start the pendulum swinging.

Which winding hole on my clock does what?

The middle hole will wind the spring that powers the timekeeping function of the clock. The right hole, as you're looking at the clock, powers the chimes of the clock. Finally, the left winding hole, as you're looking at the clock, powers the hourly strikes of the clock.

How do you wind a clock spring?

3:099:16Chapter 13 - Mainspring and Spring Winder - YouTubeYouTubeStart of suggested clipEnd of suggested clipDirection. With one hand on the winding handle cup your other gloved hand over the top of theMoreDirection. With one hand on the winding handle cup your other gloved hand over the top of the mainspring. And slowly wind the spring until the c-clamp comes loose.

Do you stop pendulum to wind clock?

Can I wind my clock when the pendulum is moving, or should I stop it before winding? You can wind your clock when the pendulum is moving. It doesn't matter either way. I accidentally moved the hour hand on my clock, and now it won't keep correct time.

How often do you wind an antique clock?

Wind firmly to the point of resistance: the key will stop when the clock is fully wound. An eight-day clock should be wound once a week, as the mainspring loses power after seven days. A 30-hour clock should be wound daily; a good routine is to wind it every night before bedtime. The key should fit tightly.

Can you over wind a clock?

It's actually impossible to overwind a clock, whilst you can wind a clock until it cases internal damages and breakages, it's impossible to continuously wind a clock.

The History of the Antique Mantel Clock

Mantel clock (around 1800) by Julien Béliard, Paris, maître horloger recorded on the rue Saint-Benôit and rue Pavée in 1777, still active in 1817, or Julien-Antoine Béliard, maître horloger in 1786, recorded on the rue de Hurepoix, 1787–1806. (Credit: Wikimedia)

Types of Antique Mantel Clocks

A quick way to identify antique mantel clocks is by understanding the different types. Long before manufacturers started leaving signatures on their products, they had unique styles. Experienced collectors can tell a brand by looking at the design, and now you would too.

Identifying Antique Mantel Clocks

At this point, you should have sufficient knowledge of antique clocks, so identifying one should be a piece of cake. But there are a few more hurdles to jump. Once you study the fine print, you’ll assess an antique mantel clock like a seasoned collector.

Antique Mantel Cocks Value Guide

Now to the final step in your training – how do you know when to bid higher or fold? Antique mantel clocks sell between $100-$10,000 depending on certain qualities.

Concluding Thoughts

Please give yourself a round of applause; you made it to the guide. You can identify and value antique mantel clocks now. Before you go, let’s refresh your memory with a few key points;

What are the two clocks mentioned by Richard T?

This info. is also in another thread. The two clocks mentioned by Richard T are named the Theben and the Standard. The Standard is shown with columns on either side of the door; hence I would opt for the Theben, if it is indeed one of those two.

How to tell if a clock is in a beat?

Theoretically, the clock movement is in a level position if the pendulum hangs in the center of the beat plate when at rest. The clock is in beat if it travels an equal distance either side of the center mark. In reality, even a small adjustment of the position of either the movement or beat plate may throw this off.

How big is a C. 1883 clock?

They are C. 1883 and were available in either one day or eight day time and strike. The size is about 18 inches which is close to your measurement (if my metric is correct). Again, welcome and we look forward to seeing additional pictures of your clock.

Can you wind the clock first?

You may wind either one first. It makes no difference. On some clocks, winding the time side ten minutes or less before the hour can cause the clock to strike the coming hour, and you will need to adjust the hour hand forward because when the minute hand reaches the hour, the clock will strike the next hour.

Can you take your old clock in for repairs?

It's nice to have the old key BUT ... when you take your clock in for repairs, be sure to take your old key. The repair person can check it (for fit) and replace it, if necessary. Many old keys are worn out and a bad key can cause severe damage to your clock. anti-clockwise.

How to wind a mechanical clock?

Winding your mechanical clock. If the dial is covered by a glass door, open it to access the face. Insert the key into one of the winding arbours and with your non-dominant hand, steady the case while you wind the clock. I recommend wearing cotton gloves to preserve the finish of the case. Next, turn the key clockwise.

How to keep brass finish on clock?

Wear cotton gloves to steady the weights while they are being pulled up to preserve the brass finish on the weight shells. For those clocks that wind with a crank key, insert the key into each winding hole on the clock face and crank slowly till the weights reach the top .

What is the arbour on a clock?

On a clock with three arbours, the centre arbour winds the time train and the left arbour, the strike side and the right, the chime side. On some clocks, there is a smaller hole on the clock face near or above the 12 o’clock position. It is also an arbour but a smaller one used for regulating the speed of your clock.

Why do clocks have two ends?

Two ends are required because the speed adjustment arbour is smaller than the winding key arbour.

What is the hole in the clock on the Ingraham clock?

The smaller hole in the loop end of the “2” on the number 12 is for regulating the clock.

How many half turns does an 8 day clock need?

An 8-day clock usually requires 14 half turns of the key as the arbour does one complete turn per day. Mainspring ratchet and click. The ratchet locks the spring in place during each wind of the key. Allow the key to gently rest back onto its click.

What is a winding arbour?

Each winding arbour has a function. The number of winding arbours corresponds to the number of gear trains (or sets of gears) on a clock. For example, if there is one hole it is a time-only clock; 2 holes mean that it is a time and strike clock, that is, it strikes the appropriate hour on ...

How to clean a pivot point?

Then using a very sharp, thin pivot cleaning stick (barbecue sticks can also be used) scrape out any dried oil and dirt that has collected in and around the pivot points.

Can you use synthetic oil on a clock?

They could even stain dials and are not recommended. As for the right kind of oil, there are a number of excellent brand name synthetic clock oils available on the market today. They protect your clock from wear and tear and tend to stay where put. So it’s best to use them and keep your clock happy.

Does servicing your own clock void warranty?

Before you do anything: If you have a newer clock that’s still covered under the manufacturer’s warranty, be sure to check with them first beforehand, since servicing your own clock could void the warranty.

image

1.Videos of How Do You Wind Ansonia Mantel clock

Url:/videos/search?q=how+do+you+wind+ansonia+mantel+clock&qpvt=how+do+you+wind+ansonia+mantel+clock&FORM=VDRE

9 hours ago  · How do you wind Ansonia mantel clock? To wind the clock simply place the key, or crank, into the winding point and turn clockwise sixteen revolutions. When the clock is fully wound an internal mechanism will prevent you from winding any further.

2.How Do You Wind Up a Mantel Clock? - Chelsea Clock

Url:https://www.chelseaclock.com/blog/how-do-you-wind-up-a-mantel-clock

16 hours ago  · To do this, gently and slowly move the minute hand in a clockwise direction. Stop at the appropriate chime or strike intervals and let them complete in full before continuing. Make sure to wind the clock before moving the hands, as forcing them can break the mechanism.

3.Ansonia mantle striking clock with no self correcting

Url:https://www.youtube.com/watch?v=2odbcE30dIQ

14 hours ago  · http://www.timepiecesnz.comSales of wristwatches, pocket watches, clocks and barometersSee our website for other Timely Tips

4.The Complete Guide to Antique Mantel Clocks

Url:https://www.txantiquemall.com/antique-mantel-clocks/

8 hours ago Crystal Face and Pendulum Clock Made by Ansonia Clock of New York (Credit: 1stDibs) ... you have to wind the antique mantel clock with a key at intervals. Typical antique mantel clocks are “8-day” wounds – you wound them once in eight days. However, there are also “14-day” and “31days” designs, but they cost more because of rarity

5.Dating Ansonia Clock | NAWCC Forums

Url:https://mb.nawcc.org/threads/dating-ansonia-clock.53636/

28 hours ago  · Wind it clockwise until it is tight. You may wind either one first. It makes no difference. On some clocks, winding the time side ten minutes or less before the hour can cause the clock to strike the coming hour, and you will need to adjust the hour hand forward because when the minute hand reaches the hour, the clock will strike the next hour.

6.Winding a mechanical clock – How To - Antique and …

Url:https://antiquevintageclock.com/2017/05/04/how-to-wind-a-mechanical-clock-the-basics/

29 hours ago  · Winding your mechanical clock If the dial is covered by a glass door, open it to access the face. Insert the key into one of the winding arbours and with your non-dominant hand, steady the case while you wind the clock. I recommend wearing a cotton glove on your non-dominant hand to preserve the finish of the case. Next, turn the key clockwise.

7.Repairing Ansonia time & strike clock Part 1. How to …

Url:https://www.youtube.com/watch?v=jZOzTaEnRQY

32 hours ago  · So apply the oil in small amounts and if you see any bulging, carefully wick up the excess with the tip of a tissue. At the same time, use enough oil. If there’s too little, you’ll have to re-oil in a few months or worse, your movement will wear prematurely due to lack of lubrication. So it’s good to be careful when applying oil.

8.How to Spot Clean and Oil Your Clock - The Well Made …

Url:https://www.thewellmadeclock.com/how-to-spot-clean-and-oil-your-clock/

25 hours ago You can find several other examples online of the "Burton" and they all look like your family's clock so perhaps Ansonia made the model's design a little more ornate before it went into production. At any rate, the clock has an 8-day Time and Strike Movement and listed for $5.50 in 1894.

9.Ansonia Mantle Clock - Family Heirloom | Collectors Weekly

Url:https://www.collectorsweekly.com/stories/288065-ansonia-mantle-clock--family-heirloom

31 hours ago To wind, simply insert the crank into the winding points turning clockwise approximately thirteen revolutions. As you turn the crank you should see the weight rise. When fully wound, the weight should hit the underneath of the "seat-board" and prevent you from winding anymore. Repeat this process for each of the winding points.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9