How To Winterize A Sand Filter
- 1) Set the filter to "recirculate" or "whirlpool" if you have these settings. ...
- 2) Without changing the blower or filter head settings simply turn off the blower and then remove the filter pressure gauge (careful, these break very easy) as well as the backwash sight glass. ...
- 3) Turn off the blower and change the filter head setting to "winter". ...
How do I winterize my sand filter?
Hi Rich, To winterize your sand filter, remove the drain cap at the bottom of the filter tank to let the entire filter drain and leave the drain cap off until Spring. Move the valve handle at the top of the filter to the “Winter” position. You can now remove both hoses that connect the filter to the pool.
What should I do if my sand filter is not working?
Disconnect and drain the water pump and all unused hoses. Place the sand filter, water pump, hoses, the drain cap and pressure valve in a dry, safe place until the pool is ready to be used again.
How do I winterize my swimming pool?
Adjust the pool water to the correct PH levels before winterizing. Leaving water in the pump and filter could cause them to break during freezing weather. A swimming pool must be properly winterized when not in use during the cold winter months. Proper maintenance of your pool's equipment is essential to keep it running correctly.
How do you winterize a snowblower water filter?
After a backwash and rinse, place the valve to the “winterize” setting on the top mount valve. This will allow water to drain from the valve. Next, you’re going to have to completely drain all the water from the filter tank. To do this simply unscrew and remove the drain cap on the bottom of the filter barrel.
How do I close my pool with a sand filter for winter?
0:452:27How to Winterize an In-Ground Pool With a Sand Filter : Pool MaintenanceYouTubeStart of suggested clipEnd of suggested clipYou have to blow out your return Jets and your skimmers. And you can usually do this using a shopMoreYou have to blow out your return Jets and your skimmers. And you can usually do this using a shop vac or an air compressor. And you would do that at the pump or at the filter system.
Do I need to empty my sand filter for winter?
It is very important that you properly store your filter system for the winter to avoid any damage that could be caused by the freezing temperatures. After draining your pool for the winter: Remove the drain plug from the bottom of the filter tank and allow all water to drain from the system.
How do you winterize a Pentair sand Dollar filter?
Clean the filter. Remove the filter hoses. Spray the cartridge filter elements and D.E. (diatomaceous earth) grids with Filter Cleaner, then rinse them clean with a garden hose. For D.E. filters, drain the filter tanks and leave the backwash valve open. If you have a sand filter, clean it by backwashing.
How do you drain a Pentair sand filter?
0:191:07How to drain your pool (Sand Filter) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow when we're adjusting the valve for a sand filter the pump has to be turned off so make sure yourMoreNow when we're adjusting the valve for a sand filter the pump has to be turned off so make sure your pumps turned off once. It's turned off you can move the dial at the top here to waste.
Can I leave my pool sand filter outside in the winter?
Sand filters should be left outside. Remove the drain plug on the bottom of the filter. Remove the valve from the filter and store inside.
Should you cover your pool filter in winter?
In our region, where temperatures routinely fall below freezing for an extended period of time, a pool filter must be winterized to avoid cracking due to the expansion of freezing water inside the filter. A cover will not help the filter from freezing, but will protect the exterior from oxidization.
Should I drain my sand filter?
Drain your sand filter, water pump, and hoses and put them in storage when not in use. Most sand filters have a winterize setting that you can use when you are ready to shut it down for the year.
How do I prepare my pool filter for the winter?
After a backwash and rinse, place the valve to the “winterize” setting on the top mount valve. This will allow water to drain from the valve. Next, you're going to have to completely drain all the water from the filter tank. To do this simply unscrew and remove the drain cap on the bottom of the filter barrel.
How do you winterize an above ground sand filter?
If you're trying to winterize an above ground pool with a sand filter, then the first step is walking over to your multiport valve and set it to “Winterize”, or any equivalent setting that allows the filter to drain. After that, simply remove the plug at the bottom of the filter.
How long does it take to drain a sand filter?
If you need to drain the filter, unscrew the drain cap at the bottom of the sand filter, and drain the filter for at least 12 hours, otherwise the sand will be very wet and difficult to remove. Once the sand is well-drained, it's time to open the sand filter housing.
How do you get water out of a sand filter?
As you start to plan for your pool winterization process and any off-season maintenance, you'll want to take a look at your sand filter....Turn Off Your Pump Timer. ... Open the Drain Plug to Release Pressure. ... Remove the Drain Plug Completely. ... Connect a Hose to Direct Water Runoff.
How do you drain Pentair pool equipment?
0:050:37How to drain water from your pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipWater will drain out if you want to connect a hose to it and run it somewhere you can or you canMoreWater will drain out if you want to connect a hose to it and run it somewhere you can or you can just let it run off the pad depending on your drainage. I recommend setting your kitchen timer.
How do I winterize my above ground pool without draining water?
0:392:46Do You Need to Lower the POOL WATER When You Close? - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you have an above ground pool just make sure you remove the hose off the bottom of the skimmer.MoreIf you have an above ground pool just make sure you remove the hose off the bottom of the skimmer. And make sure you install a winter cover plate. On your above ground pool.
When should I winterize my above ground pool?
In most areas, you need to winterize your above-ground pool around mid-October or when the pool water dips below 65°F and consistently remains below that point. Do not winterize the pool too early, or the winterizing chemicals will lose their potency before the end of the winter.
How do I winterize my above ground pool pump?
4:3910:37How to WINTERIZE An Above Ground POOL | Swim University - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd other filter equipment in a warm dry place all winter long if your pump and filter are tooMoreAnd other filter equipment in a warm dry place all winter long if your pump and filter are too cumbersome or heavy to move just make sure that you remove all the drain plugs.
How do you winterize a pool?
Steps for Winterizing an In-Ground PoolStep 1: Remove pool accessories. ... Step 2: Deep clean the pool. ... Step 3: Adjust the water chemistry. ... Step 4: Lower the water level. ... Step 5: Drain and store the equipment. ... Step 6: Add shock and algaecide. ... Step 7: Cover the pool.
How to winterize a sand filter?
The first thing you should do when winterizing your sand filter system is to perform a backwash. After the water is running clear from the nozzle, turn off the power. After you backwash, move the valve to the “rinse” position and let it run for 30 seconds. 2.
Why is it important to winterize a sand filter?
It is very important that you properly store your filter system for the winter to avoid any damage that could be caused by the freezing temperatures.
How long is sand good for in a pool?
You do not need to remove any sand from the filter. Your sand filter system ‘s sand is good for about 4-5 years. Finally you are going to disconnect all of the hoses from the filter.
What is a winter closing kit?
This Winter Closing Kit contains everything you need to close your pool this fall. It will condition the pool water and prevent algae growth throughout freezing winter months to ensure a sparkling clean pool.
How to winterize a water filter?
Clean out the filter by back washing and rinsing it out using the control lever and water pump. After the water is running clear from the nozzle, turn off the power and place it in the winterize setting on the filter top.
Why does my water pump break in freezing weather?
Leaving water in the pump and filter could cause them to break during freezing weather.
1. Flush the Pump
Adequately flush the pump and chemical solution system of all chemical residue. Be sure to remove all strainer screens and clean any residue that has build up on the screens.
2. Prevent Oxidation of Components
Fill chemical solution system components with antifreeze and spray a small volume through the system (from tank to nozzle). This procedure will prevent the elastomer components from “drying out” and remove residue that continues to attack system components.
3. Open Pump Components
Leave regulators, unloaders and valves in an open or loose state so that they do not stick upon startup.
4. Drain the Winterizing Solution
Clear out the solution prior to use next spring. Retain the solution in a properly marked container for use again the following fall.
What is a sand filter?
A sand filter is a sand filter whether it be on an AGP or IG I suggest trying my method after a few days of gravity draining through the bottom. You're sure are not going to get the volume out the bottom like you would blowing it. Whats the harm in taking the extra step & 5 mins to ensure a sand filter is drained properly for your customer rather than simply relying on a guess that the water is sufficiently drained out through the bottom. It may be sufficient for southern states but to dismiss a proper method for everyone in freezing climates is a disservice to others on this board.
How to winterize a multiport?
Just remove the drain plug at the bottom, the site glass, and the pressure gauge. Leave the rest. Put the multiport on "Winter" and that s it.
How to remove remainder of a filter?
To remove the remainder is to use a high volume shopvac to blow the filter out through your backwash line. You place your dial to Rinse then place your vac hose on the line from the pump (leave you gauge and sight glass in while doing this). When blowing the air forces the water up and out.
Do you have to blow out a sand filter for an IG pool?
Those pools generally do not have the lines blown out. So, for an AGP owner, it makes no sense to go to the trouble to blow out a sand filter when its not really needed. If you noticed, i did say that if you are already blowing out the lines for an IG pool, sure, put the multiport on rinse and blow it out. But its not necessary.
Can you take the drain plug off the bottom of a water filter?
You can do that if you want, but it's not really necessery. Removing the drain plug at the bottom and letting the water drain is fine. Now, if its already freezing and you need to get it out fast, sure, thats a good way to do it. But just taking the plug off the bottom of the filter will drain the water just fine.
Can you leave a water pump outside?
I can almost guarantee there isn't a stat out there; at least not official. Leaving the pump outside just leaves it exposed to the elements more. Also the pump is not moving for that period of time so things can get rusty etc. Bringing it indoors is just a way to avoid unnecessary exposure to the elements. But if the motor is hardwired I would leave it in place as removing and re-installing wires on the pump tend to cause the wires to break from bending so much. So unless you plan on having the motor rewired to a simple plug outlet I would recommend a motor cover (or a waste basket from the dollar store cut to shape with a knife) Basically you don't want to wrap the motor in plastic as this just traps in moisture. By having a lose fitting motor cover etc on the motor it keeps the snow and rain directly off the motor but still allows it breathe and dry up.
Do you backwash a filter before winterizing?
Just make sure to give the filter a good backwash before winterizing as this will help the filter drain easier when the plug is pulled. I've seen some filters only drip when the drain plug was removed because the filter was so dirty.
How to keep sand filter fresh?
To keep your sand filter fresh, give it a backwash. You’ll know you’re done when the water runs clear from the nozzle. Then you can power down and move on to the next step.
What Does Winterizing A Pool Filter Mean?
Unless you live in the tropics and can swim all year round, you’ll probably want to shut your pool down for the winter to save on your monthly energy bill without running your pump for eight hours or so a day.
Where is the top mount valve on a sand filter?
Winterizing a sand filter will make you very familiar with your top mount valve, which is located at the top of your sand filter pump.
Can you winterize a sand valve?
Now that your sand or other media is as clean as it can possibly be, you can turn that valve to the ‘winterize’ setting. This will let the water drain from the valve.
Can a pool filtration system be closed in winter?
If you live in a place that experiences freezing winter temperatures, not closing your pool filtration system properly could lead to cracked pipes.
Can you leave a filter outside in winter?
Even if your filter doesn’t crack, leaving it outdoors for the winter could cause avoidable wear and tear.
Is it a waste of time to switch sand in a pool?
Of course, switching your sand every time you shut your pool down is a waste of time and money.