Knowledge Builders

how do you wire a motion light to an extension cord

by Kariane Kautzer Published 3 years ago Updated 2 years ago
image

Just put a three-prong male plug on the motion light, then plug it into the extension cord. Green goes to the ground prong, black and white go to the other prongs (doesn’t matter which with these two). Can you wire a light socket to an extension cord?

Full Answer

Can you wire an outside light to an extension cord?

Assuming that you plan to plug the light into an outdoor receptacle, drill a hole into the base of the fixture large enough for the cut extension cord (which you will do in another step) to pass through. Keep in mind that this hole will look better towards the bottom of the base of the fixture.

How do you wire an extension cord to a light switch?

3:498:19EXTENSION CORD WITH A SWITCH PROJECT - YouTubeYouTubeStart of suggested clipEnd of suggested clipLine basically this is the one this with the male plug. This is always hot when you're plugging inMoreLine basically this is the one this with the male plug. This is always hot when you're plugging in basically that comes in he'll to the switch.

Can I wire an outside light to a outlet?

When you connect an outside light to a plug you don't want wires running everywhere. Outdoor lights usually have underground wiring to keep the cables safe. This also hides them from view. Even when they come above ground, such as with the wiring for pendant lights, you can hide them pretty well.

How do you hardwire an extension cord?

4:186:39How to Wire an Extension Cord - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we'll start by trimming off the outer jacket. And then we'll strip our conductors. And get readyMoreSo we'll start by trimming off the outer jacket. And then we'll strip our conductors. And get ready to install the female connector. Body. So I've laid this connector body out.

How can I get power when there is no outlet?

Hook up an unused breaker to the existing electrical system, or continue wiring from an outlet in a nearby room. Run the wiring behind the drywall or other wall surface, and install outlet boxes at intervals along the wall.

Can you turn a light fixture into an outlet?

If you want to continue having a light in the fixture but need a receptacle as well, you can install a lamp-holder-to-outlet adapter instead. You don't even need to know how to replace an outlet if you use an adapter. They screw right into the outlet and contain both receptacles and a light bulb socket.

Can I use an extension cord to wire a light fixture?

You don't have to do a major wiring job. You can simply re-wire the lamp with an extension cord and plug it into an available wall outlet.

How do I extend the power from my outdoor light?

Installing outdoor power outlets isn't as difficult as it sounds. The quickest way to extend power outdoors is to install a receptacle back-to-back with one inside the house. You also can drill through the wall from a basement or crawlspace and attach a receptacle on the side of a house using an extension ring.

Can light switches and outlets be on the same circuit?

In your case it is okay to install a receptacle alongside the switch. However you need a neutral as well as a hot wire which you may not have. Test to see if you have a neutral with a test light or meter. The neutral will be white but some switches are wired up with a white wire that is not a neutral.

What are the 3 wires in an extension cord?

The green wire is the ground wire, the white wire is the neutral wire, and the black wire is the hot wire. Light-duty interior extension cords often lack the ground wire, but if a ground wire is present, be sure to connect it.

Which prong is hot on extension cord?

Standard extension cords are available with either two or three prongs. One prong is “hot,” the second is “neutral,” and the third serves as a path to the ground wire.

What are the three wires in a cord?

The live, neutral and earth wires are in the plug. The live wire is brown and the neutral wire is blue in a plug.

Can interior and exterior lights be on the same circuit?

Yes, interior and exterior lights can be on the same circuit.

How do I wire a receptacle from a light outlet but keep it hot when light is off?

In this case, you must change the cable from the switch to the light outlet from a 2-wire to a 3-wire cable. As you can see, connecting a receptacle to the light would see the receptacle only hot when the light switch is on.

What is a swag light?

They are not fixtures. They are lamps that plug into the wall and are suspended from a hook in the ceiling, usually by a decorative chain. I understand about the U.L. listing, but if this was properly done it wouldn't be unsafe.

Can you use an extension cord with a lamp?

That may be true, but you can not use an extension cord, you would have to use lamp cord.

image

1.Adding a motion sensor to an extension cord

Url:https://www.doityourself.com/forum/electrical-ac-dc/503672-adding-motion-sensor-extension-cord.html

23 hours ago Just put a three-prong male plug on the motion light, then plug it into the extension cord. Green goes to the ground prong, black and white go to the …

2.How to wire Motion Sensor Light | installation and wiring …

Url:https://www.youtube.com/watch?v=06RZT0TiDrA

15 hours ago  · In that case, building codes have nothing to do with this. You could most certainly use an extension cord. But two-prong plugs are polarized (one prong is wider than the other) so you would have to be sure to properly connect the two wires to the lamp. That's where rjniles' advice comes in - if you don't know how to figure that out, don't do it.

3.How to wire light fixture to extension cord? - DIY Home …

Url:https://www.diychatroom.com/threads/how-to-wire-light-fixture-to-extension-cord.165051/

25 hours ago The safest way to work on or install light switch or electric AC outlets is to turn off circuit breaker switch for that room and go by your wire diagram or c...

4.Adding a Light Socket to an Extension Cord - YouTube

Url:https://www.youtube.com/watch?v=klMfjv4K_Ps

14 hours ago  · Hold the ends of the matching wires together so they are parallel and then twist them clockwise (using pliers if need be)…. Step 4: Then thread them into a twist-on wire connector (aka wire nut, or Marrette), making sure that all the exposed wire is covered by the Marrette. Step 5:

5.HOMEMADE ELECTRICAL EXTENSION CORD WITH …

Url:https://www.youtube.com/watch?v=zKzvJNVgM-Q

29 hours ago Different options for the wiring and repair of a damaged extension cord.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9