Zing Ear ZE-268s2 Wiring Instructions
- Turn off electrical current at source by turning off circuit breakers
- Do not cut wires, multi-strand wires are solid and soldered together so they can be attached to the switch
Full Answer
How do you remove wires from a fan switch?
Remove wires from existing fan switch. If wires are hard to remove, insert a paper clip or a large sewing needle into each hole (numbered 1, 2, 3, L) and pull the wire out (repeat this step for each wire) Make sure that the wire lead length is the same length as the line beside word “STRIP”
How many wires does a ceiling fan capacitor have?
The capacitor usually has 2 wires on one end: 2 blacks, 2 grays, or 2 yellows. One of these wires is connected to terminal “1” on the switch Zing Ear ZE-268s6 (3-speed fan switch) can be used to replace ZE-268s5 and ZE-208s5-1T (4-speed fan switch); however, the ceiling fan will no longer support 4 speeds as ZE-268s6 supports 3 speeds only.
What should I do before rewiring my Ceiling Fan?
Before rewiring any ceiling fan. Turn off electrical current at source by turning off circuit breakers Failure to disconnect power to the ceiling fan may cause electrical shock, fire hazard, serious injury, or death Do not cut the wires off the existing switch. multi-strand wires are solid and soldered together so they can be attached to the switch
How do you turn off the power to a ceiling fan?
Turn off electrical current at source by turning off circuit breakers Failure to disconnect power to the ceiling fan may cause electrical shock, fire hazard, serious injury, or death Do not cut the wires off the existing switch. multi-strand wires are solid and soldered together so they can be attached to the switch
How do I wire a zing ear switch?
StepsWrite down the color of each wire and the portal number to which they are attached.Take wires off the existing switch.Make sure that the wire lead length is the same length as the line beside word “STRIP”Connect wires to the new switch as noted in step 1.
What color wires go to 3 speed fan switch?
black: common. blue: 3µF, 350V. red: 3.5µF, 200V. yellow: 6µF, 200V.
How do you wire a fan switch?
0:384:50How to Wire a Ceiling Fan | Lighting and Ceiling Fans | The Home DepotYouTubeStart of suggested clipEnd of suggested clipThe black wire powers the fan. The white is neutral. The green wire is for the ground. And a redMoreThe black wire powers the fan. The white is neutral. The green wire is for the ground. And a red blue or striped wire can act as a conductor to carry power to the fans light kit.
How do you wire a 4 wire fan switch?
1:315:59Replace a 3-way 4 wire ceiling fan switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipSomething might be different with this four wire one what's really nice is that there are numbers onMoreSomething might be different with this four wire one what's really nice is that there are numbers on the bottom that go with each of the wires right so one two three and L.
Can black and red wires go together?
These wires are typically used for switch wiring as well as the interconnection between smoke detectors hard-wired into the power system. You can link two red wires together, or you can link a red wire to a black wire. Since red wires conduct current, they are considered hot.
How do you wire a 3 way fan switch?
0:337:293-way combination switch, wiring a ceiling fan/light - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo black wire is gonna hook up to the top screw. From my fan and then my white wire and my red wireMoreSo black wire is gonna hook up to the top screw. From my fan and then my white wire and my red wire are going to be travelers. That go up and they connect together that lead to this other switch.
What color wires go together?
See Table below. The protective ground is green or green with yellow stripe. The neutral is white, the hot (live or active) single phase wires are black , and red in the case of a second active....US AC power circuit wiring color codes.FunctionLine, 3-phaselabelL3Color, commonblueColor, alternativeyellow5 more columns
Does the red wire connect to black or white?
Attach the black wire to the outlet you want to always be on (usually the top one) and the red wire to the switched outlet. Connect the white wire to either of the chrome screws (remember, they are still joined) and the ground wire to the green ground screw.
Which wire is hot when both are same color?
In most modern fixtures the neutral wire will be white and the hot wire is red or black. In some types of fixtures, both wires will be the same color. In this case, the neutral wire is always identified by some means. In some cases, there will be small writing on the wiring case.
Why does my ceiling fan have 4 wires?
In order for the light to be controlled by its own switch, the wiring between the switch and the fan unit needs a fourth wire, a red wire, to carry power to the light kit.
What is the red wire in a light switch?
What are Red Wires? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.
What does the L on a fan switch mean?
Positions: OFF, High speed=L-1, Medium speed=L-2, Low speed=L-3.
How do you wire a 3 speed fan motor?
0:329:03Wiring a 3 Speed Blower Motor - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe you would wire your white to white neutral. From the line and then you would wire your hot wireMoreThe you would wire your white to white neutral. From the line and then you would wire your hot wire from the line to black and you'd have high speed only and you just cap your other two wires.
What is the color code for ceiling fan switch?
The black wire is the hot wire that leads to the switch. The white wire is neutral and completes the electrical circuit. Copper or green wire is the ground wire and keeps the fan from experience power surges. If there is a blue and black wire coming from the household circuit, there should be two switches on the wall.
How do I bypass a 3 speed fan switch?
5:4411:083 speed Box fan bypass or replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you want to bypass if you don't want to mess around with a switch you can just hook up to oneMoreSo if you want to bypass if you don't want to mess around with a switch you can just hook up to one of the wires. These the ones going to the motor.
How do you fix a 3 speed ceiling fan?
0:113:33How to Repair a Three-Speed Ceiling Fan - YouTubeYouTubeStart of suggested clipEnd of suggested clipBox for all the electrical here and it's hooked to a pull chain a lot of times people pull too hardMoreBox for all the electrical here and it's hooked to a pull chain a lot of times people pull too hard on the chain it breaks off simple fix go ahead and remove. The old control switch.
How many wires should a fan capacitor have?
Usually, there is no connection between this switch and the fan capacitor; however, the capacitor should have one microfarad reading and should have 2-3 wires. Two of the wires should be the same color on one end, for example, one end has 2 reds and the other end has 1 White.
What happens if you disconnect a ceiling fan?
Failure to disconnect power to the ceiling fan may cause electrical shock, fire hazard, serious injury, or death. Do not cut the wires off the existing switch. multi-strand wires are solid and soldered together so they can be attached to the switch.
What happens when you push wire into a hole?
What happens, is when you push the wire into the hole, that tab will push downward. Once the wire is past the tab, it is locked into place as the tab will not move in the upward direction . It locks against the wire to keep it in place and make contact in the switch. 1.
Can you push stranded wire into a switch?
If you can get short pieces of solid wires the same size as the stranded ones, you can push those into the switch and then wire nut the wires to the short ones installed on the switch. Sometimes it is a combination of the safety pin and solder or solid wire, just depends on how tight that tab is inside.
