How to make a log splitter with a Jack?
Steps on How to Build a Log Splitter with a Hydraulic Jack
- Build the Frame. Before anything else, you must build the frame for the log splitter. ...
- Build the Sliding Block. After your frame is built, you can begin to build your sliding block. ...
- Mount the Hydraulic Jack. ...
- Attach the Wedge to the Jack. ...
- Attach the Wheels If You Choose to Have Them. ...
- Test Your Hydraulic Jack Woodcutter. ...
How do hydraulics work on a log splitter?
The Machine has six main parts-
- An Electric Motor or Engine -this is the power source. ...
- The Hydraulic Pump -The pump creates a high-pressure oil stream, and the oil goes to the valve.
- A Tank -This is the storage of the hydraulic pump oil.
- A Valve -You turns it on like a gear to start the process of splitting the log.
How to fix a log splitter?
How to Repair a Log Splitter
- Troubleshoot – Oil Pump. Knowing precisely what is wrong with your log splitter is the first step to repair. ...
- Engine. Check the engine. ...
- Hydraulic Cylinder. Assuming the cylinder is not severely damaged, that is, has not swelled, cracked, and the piston rod is not damaged, a faulty seal or piston ...
- Valve. ...
How to connect a log splitter?
These 4 simple steps will get you on the road:
- First lower the beam into the horizontal position. It should automatically lock, but always double check.
- Then remove the spring clip and clevis pin from the jack stand. ...
- Unless you’re the hulk, lifting your log splitter is not an option. ...
- Once secure, just connect the chains, plug in the taillights, and remember to turn off the fuel value. ...
What are the benefits of a kinetic log splitter?
The biggest and most commonly considered advantage of kinetic splitters is their speed. Kinetic splitters are fast. Many of them have cycle times (the time it takes the splitter to split a log and return to its starting position) of 2.5-3 seconds.
How do you use a kinetic log splitter?
0:542:44Oregon Kinetic Log Splitter - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen the control handle moves forward the rack presses on to the pinion gear the rack and push plateMoreWhen the control handle moves forward the rack presses on to the pinion gear the rack and push plate power forward at high speed pushing the log through the wedge.
How does a log splitter use hydraulics?
In a typical log splitter, the operator places a log on the splitter, then shifts a directional valve to route fluid from the pump to the cap end of the hydraulic cylinder. The combined flow from both pumps extends the cylinder's piston rapidly to reduce the time it takes to advance the wedge to the engage the log.
Do foot operated log splitters work?
It's a great – and cost-effective - alternative to hydraulic log splitters and just requires a few foot pumps to split a log. Saving time and effort, this log splitter will revolutionise a potentially dangerous and often arduous job.
Are kinetic wood splitters any good?
If you're looking to split for commercial business purposes, then a kinetic log splitter will definitely save you time and money in the long run. Additionally, if you're splitting harder woods and need to upgrade to a higher tonnage model of a hydraulic splitter, then this will start to cost around the same price.
What RPM should a log splitter run at?
400 - 600 rpmThe speed of the splitting log splitter should be in the range of 400 - 600 rpm. Higher rotations than recommended will cause the bit tip to overheat which may lead to hardening and damage.
How much HP does it take to run a log splitter?
If you are serious about making your own backyard log splitter, then you want to have, at a minimum, the following components to provide the right amount of force and power for basic splitting of averaged sized, seasoned logs: A 5 Horsepower engine. A two-stage hydraulic pump rated at a max of 3 gpm at 2,500 psi.
Is vertical or horizontal log splitter better?
Vertical log splitters will have a higher tonnage so are capable of splitting hard or green wood of much larger diameters than a horizontal wood splitter. A 7 tonne vertical splitter will easily cope with logs of 12” diameter.
Where do you put hydraulic fluid in a wood splitter?
0:361:25Log splitter hydraulic fluid fill tip - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp on the log splitter. And then you can just tip it over. Like this get over here where you can seeMoreUp on the log splitter. And then you can just tip it over. Like this get over here where you can see it. Maybe i can go out just a little bit there you can just tip it over.
What is the best log splitter for your money?
What Is The Best Log Splitter To Buy?YardMax 28 Ton HV Log Splitter - Half Beam - Gas Log Splitter.10 Ton Boss Industrial Dual Action Electric Log Splitter - Electric Log Splitter.Boss 8 Ton Industrial Dual Action Electric Log Splitter - Electric Log Splitter.YardMax 5 Ton Electric Log Splitter - Electric Log Splitter.More items...
Who makes the best log splitter for the money?
The best log splitters: Reviews & RecommendationsBest overall: Champion Power Equipment Compact Log Splitter.Best gas: NorthStar Horizontal/Vertical Log Splitter.Best electric: Boss Industrial ES7T20.Best manual: Fiskars IsoCore 36-Inch Maul.Best budget: Southland Outdoor Power Equipment SELS60.
What weight is best for log splitting?
8 poundsThe best weight for a splitting maul is 8 pounds. This weight provides a sufficient amount of power for splitting logs while remaining light enough for most people to manage. Mauls generally span between 4 and 12 pounds.
What is the best way to use a log splitter?
Log Splitter Tips And TricksUse the ramstop. ... Aim to split the log off centre slightly. ... Use good quality oil. ... Keep any knots in the wood pointing upward. ... Avoid splitting seasoned logs, if possible. ... Buy a stand, it's worth it. ... Protection is important. ... And perhaps most importantly, keep the splitter level.
What oil do you use in an electric log splitter?
Hydraulic oilAW22 or 32 Hydraulic oil is recommended for the log splitter. Automatic transmission fluid can be substituted and should only be used instead of hydraulic oil when temperatures are below 32 degrees F.
How do you use a small electric log splitter?
2:0114:46WoodEze Electric Log Splitter Demo - Impressive Power! - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. You just plug it in and you're ready to go it's a very simple operation. It's got a lotMoreBasically. You just plug it in and you're ready to go it's a very simple operation. It's got a lot of power and we're going to demonstrate that right.
Where do you put hydraulic oil in a log splitter?
0:322:45Electric Log Splitter Hydraulic Oil Check - How-To from Titan ProYouTubeStart of suggested clipEnd of suggested clipBut not over so locate a suitable funnel. Make sure it's nice and clean get your ISO 3200 oil pour aMoreBut not over so locate a suitable funnel. Make sure it's nice and clean get your ISO 3200 oil pour a little bit in now it's better to pour a little bit in checking. It two or three times.
What is kinetic energy?
Kinetic energy is no new-fangled concept, it’s just taking us some time to realize how it can be used in the context of a log splitter. Also known as flywheel log splitters, kinetic splitters utilize huge flywheels to convert energy from the engine into log splintering excellence. A flywheel is a round mechanical device used to harness ...
How long does it take for a hydraulic log splitter to reset?
They can complete their push/retraction cycle in as little as 2.5 – 3 seconds, whereas hydraulic splitters tend to take around 12 – 15 seconds to reset. This is because the flywheels are constantly building pressure before their explosive release.
What is a log splitter?
Some foot-operated log splitters are vertically oriented, but most are floor-bound mechanisms usually just over a meter in length. They normally consist of a foot pedal, a hydraulic pressure plate, a loading platform, and a splitting wedge at the opposite end.
How much pressure does a log splitter have?
As the log is pushed quickly into the splitter, back pressure builds to around 700-800 PSI, triggering the bypass valve in the pump. Now the larger of the gears start passing oil back into the pump inlet.
What are the different types of log splitters?
You’d be forgiven for thinking a log splitter is a log splitter and that’s that, but there are actually three different types of log splitter: manual, hydraulic, and kinetic. Each of these has certain benefits and limitations. To decide which one, if any, is right for you, you’ll need to think carefully about what you require from a log splitter.
What is a flywheel on a sewing machine?
Picture an antique sewing machine. You have the foot pedal that spins the large wheel, which in turn spins the smaller wheel attached to the machine. These are flywheels. They force the pressure plate along the platform into the splitting wedge and voila! Firewood for days.
What is GC1000S auto retract?
Auto Retraction - The GC1000S automatically retracts, leaving your hands free to load the next piece of wood. 2x Hardened Steel Pinion Gear - Pinion gear is made from case hardened, industrial steel to reliability transfer energy from flywheel to the ram.
How does a kinetic log splitter work?
A kinetic log splitter doesn’t use oil and hydraulics. Instead, these machines have an engine that turns two enormous flywheels. The flywheels in the DR RapidFires weigh either 75 or 55 lbs., depending on the model you choose. Because of their weight, they store kinetic energy as they spin. And the heavier the flywheel, the more energy they store. The flywheels turn a 5-lb. pinion gear made of hardened steel. When you engage the handle of the splitter, the rack comes down onto the pinion gear, which pushes the ram out of the flywheel housing and through your log with a quick burst. The whole cycle time is only about 3 seconds. Compare that to hydraulic splitters’ cycle times that can be anywhere from 15 seconds to upwards of a minute! Plus, the kinetic splitters require a lot less maintenance because there are no valves or oil to worry about.
What is a Rapidfire log splitter?
That means that it works completely differently from most log splitters out there. Most log splitters are hydraulic, which means that the engine pushes oil into a hydraulic cylinder and the pressure of that oil pushes the ram through a log.
Who Should Use a Kinetic Wood Splitter?
As they say, time is money, and the speed of kinetic splitters makes them appealing for firewood sellers and other commercial users , who need to split wood quickly in order to maximize their sales volume. The price point on kinetic units makes them a natural fit for the commercial market as well.
How does a kinetic splitter work?
In place of hydraulic pump systems, kinetic splitters use massive flywheels to convert energy from a motor or engine into a burst of force. That force drives a moveable rack and push plate into a log and pushes the log against the splitting wedge, breaking the wood apart.
What is a log splitter?
Most log splitters are hydraulic log splitters. They use the power of a hydraulic pump to move the ram that forces the splitting wedge deep into a log. However, there is another type of log splitter that you’ll find on the market: the flywheel log splitter or kinetic log splitter. YouTube.
Why is a log splitter so fast?
The reason for this high speed is that the energy that drives a kinetic splitter is built up by the spinning flywheels and stored until the moment the log splitter’s operator releases it by moving a lever. Once the energy is released, it explodes as a powerful , quick push of the ram. The splitter’s ram then automatically returns to its starting position.
Why is there no tonnage rating on a kinetic splitter?
Keep in mind, the high speed is the reason that you won’t always see a tonnage rating for a kinetic splitter. Tonnage is a measure of gradually applied pressure, and it’s easier to measure on a slower-moving hydraulic log splitter. If you do see a tonnage rating for a kinetic splitter, it was calculated by comparing that machine’s splitting ability to the tonnage on a hydraulic unit.
What is the advantage of kinetic splitters?
The biggest and most commonly considered advantage of kinetic splitters is their speed. Kinetic splitters are fast. Many of them have cycle times (the time it takes the splitter to split a log and return to its starting position) of 2.5-3 seconds.
What kind of wood do kinetic splitters work with?
Finally, kinetic splitters work best with medium and soft woods, such as the wood from cone-bearing trees like pine. Extremely dense hard woods, as well as woods that contain knots and other abnormalities, sometimes present challenges for kinetic units.
How Does a Kinetic Log Splitter Work?
The working mechanism behind kinetic log splitters depends mainly on kinetic energy, hence the name.
What Is a Hydraulic Log Splitter?
Kinetic log splitters are the most common types that you might come across on the market. For example, you might find a gas-powered hydraulic splitter or an electric-powered hydraulic splitter.
How many amps does a log splitter need?
First, you need an engine. In a log splitter case, this one is either a 12 to 20 amp electric one or a four-stroke gasoline one .
What are the two mechanisms used in log splitters?
Whether they’re electric or gas-powered, most log splitters use one of two mechanisms to get the job done. These mechanisms are kinetic and hydraulic systems. But, which one is better for you?
Why are kinetic log splitters bigger than hydraulic log splitters?
For the kinetic system to work, it requires a larger surface area than hydraulic log splitter needs. That’s why kinetic log splitters are usually larger in size even if they have the same weight.
What is the advantage of kinetic log splitters?
The most obvious advantage of kinetic log splitter is the ultra-fast speed. Since this type of log splitters release all the energy at once, they usually have the shortest cycle time among all other types.
Which is better, hydraulic or kinetic log splitters?
More Powerful. One of the biggest advantages of hydraulic log splitters over kinetic ones is that they’re usually more powerful. Hydraulic systems build up a strong stream of pressure that allows it to split large logs easier than the kinetic counterparts.
What is a Kinetic Log Splitter?
A kinetic log splitter is a tool that allows you to split logs super quickly. It uses kinetic energy from an engine to push a movable rack into the log, forcing it into the splitting wedge and halving it. This saves you a ton of energy when it comes to log splitting if you’re using to doing this by hand.
How fast is a DK2 log splitter?
The DK2 40-Ton Kinetic Log Splitter is a great choice if you want something super-fast and powerful. With amazing 40-ton power and 1-second speed, it makes swift work of splitting logs. It’s a little pricey, especially if you just need it for home use, but it’s ideal if you have many logs to work with and you want to save some time.
How much power does a kinetic splitter have?
The power of a kinetic splitter is measured in tons. While it may be tempting to go for the most powerful model, they can get expensive. They can range from 5 tons through to 40 or more, but most people will find that 8-10 ton kinetic log splitters are more powerful enough for home use.
How fast can a log splitter split?
A kinetic log splitter is a great choice – they’re fairly portable, they’re easy to use, and they can split logs at very high speeds (even as little as 1 second per log). So that could save you a lot of time and energy.
What engine does a log splitter use?
It’s gas-powered, using a KOHLER Command Pro engine , which comes with a 3-year warranty. The splitting wedge is made from steel and should be able to withstand a lot of use, and the log splitter itself comes with a 3-year warranty, too.
How long does it take to split a log?
A kinetic log splitter is a big bit of kit but has the advantage of being very fast – it takes just 2-3 seconds to split a log, compared to hydraulic log splitters, which can take 12-15 seconds per log.
How long does it take for a log machine to split?
The faster this is, the quicker it will work your way through a large volume of logs. 2-3 seconds is a good time to aim for, but some are even faster.
