How do I place my bike in a steadyrack?
Scroll down below for more guidance with spacing, layout & design of your Steadyrack installation. Place the bike in the rack as shown, leave a gap between the back tyre and the wall (A) between 50mm and 75mm is ideal. This will be the distance the bike hangs above the ground when it’s in the rack.
How does the steadyrack work?
The Steadyrack really is that simple to use. Only the tyres come into contact with the rack and from there the whole bike can be swung in an almost 180-degree arc in order to make space or to access other bikes. As an added bonus, accidentally bumping a bike will simply see the rack swing, whereas simpler hooks could see bikes fall.
What is a steadyrack bike rack?
When the bike rack is empty, the arm simply folds away, making them a compact folding bike storage solution. Steadyrack bike racks can be mounted vertically to almost any wall and will conveniently swivel up to 160 degrees, from side to side. This allows for much greater flexibility and significant space saving advantages.
How far apart should bike racks be?
Measure the height of each bike when sitting on the floor to either the seat or handlebars (whichever is higher) and use this as a guide for your spacing. In this scenario with no overlap the racks may need to be as much as 1200mm ~4ft apart or more.
How far apart should Steadyrack bike racks be?
We have found that spacing your racks all the same height and about 600mm or 2 feet apart will give you a bit of both. The bikes can be folded over the top of each other but will only protrude into your floor space about half as much as they would if they were at right angles.
How close can you hang steady racks?
350mmSteadyracks can be placed as close as 350mm (1ft 2in) apart.
Can you put a road bike in a mountain bike Steadyrack?
A: The Steadyrack Mountain Bike rack works best for bikes with tire widths from 2.1 to 2.8 inches wide. The Classic Rack and Fender Rack are more ideally suited to fit bikes with narrower tires like road bikes and street bikes.
How high should you mount a bike rack?
Height. The height of the bike rack should be 33 inches tall (30-35 inches allowable), measured at the center-point of the bike rack's length. At 33 inches tall, the bike rack will be slightly taller than most bikes' top tubes.
Can you lock a bike to a Steadyrack?
And yes, you can use a lock to secure a bike to this rack.
How do you mount a steady rack?
3:295:57Steadyrack Installation Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure your rack doesn't move when you're marking the holes use the fixings provided to judge howMoreMake sure your rack doesn't move when you're marking the holes use the fixings provided to judge how deep your holes need to be drilled insert the plastic plugs first when fixing to masonry.
Is it OK to store bike vertically?
It is possible to store a bike vertically on the wall without needing to lift it at all. What you need is a wall mounting bike bracket or hook that is small enough, and fixed at the right angle, to easily fit between the spokes on the front wheel.
Is it OK to hang bike from wheel?
Concerned cyclists have pondered this question since the rise of bike theft and the decline of secure storage space for bikes. In short, the answer is no. Hanging your bike by its wheel will not damage it. At least, it won't hinder your bicycle's performance, with a few minor exceptions.
Where is Steadyrack from?
AustralianThe Australian-designed Steadyrack takes a novel approach to bike storage.
How much space do you need for bike storage?
How much storage space do I need for 1 bike? A space about 71" (180 cm) long, 25" (64 cm) wide and 43" (110 cm) high will store one average adult bike comfortably.
How much weight can bike hooks hold?
100-poundsIf it can be hung, these hooks will hold it. They are rated at 100-pounds but that is based on vertical installation.
How do you make a 2x4 bike rack?
0:318:19How to Build a Bike Rack Out of 2x4s For Your Garage - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake a level make sure your 2x4 is level drill a pilot hole. And a screw on your opposite. SideMoreTake a level make sure your 2x4 is level drill a pilot hole. And a screw on your opposite. Side against the other leg. Drive that in to have a second screw on each leg.
How do you mount a bike rack to the wall?
0:091:34Bike Rack Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a stud finder to locate the center of a stud. Place a bracket over the height and stud marks andMoreUse a stud finder to locate the center of a stud. Place a bracket over the height and stud marks and use a pencil to outline each hole. Once you've got the bracket lined up drive the top screw.
How do you attach a bike rack to concrete?
0:292:47How To Install a Commercial Bike Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipClean out the hole with a vacuum or compressed air and then clear way any debris with a small brush.MoreClean out the hole with a vacuum or compressed air and then clear way any debris with a small brush. Drive the anchor 1-inch into the concrete remove. The nuts from the anchors.
How do you mount a bike rack?
0:322:04How to Install a Strap Rack - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne mark lower and one marked side what you'll want to do is attach the lower strap first to theMoreOne mark lower and one marked side what you'll want to do is attach the lower strap first to the bottom of your trunk or to the bottom of your bumper. Followed.
Floor Space & Effort
Be aware that when staggered and overlapped, the bikes do protrude further from the wall and into your space. With rack heights staggered, more eff...
Grouping Bikes
Group your bikes so longer / heavier bikes (e.g. eBikes) are mounted lower, and shorter / lighter bikes (e.g. Road Bikes) are mounted higher. Use...
Info & Tips
If all bikes have flat bars (e.g. MTB) increase the space between racks to a minimum of 400mm (1ft 4in) to avoid handlebars clashing. For a mix of...
Maximise Floor Space
To maximise the pivot, your racks need to be set up so that the bikes do not overlap. This uses more wall space but saves floor space by reducing t...
Grouping Bikes
Bikes typically come in Small, Medium, Large and Extra Large sizes. If you have multiples of any size, group them together and mount each size at t...
Info & Tips
The height of the rear tyre rest is best set to suit each bike. Hang the longest bike first, then hang every bike in that rack to see if the positi...
SteadyRack Bike Storage – The Easy Way to Install
What if I told you there was an easy way to store 5 bikes in a very tight space, that would require minimal lifting to store them? What if I told you the installation was even easier than the manufacturer made it?
The Bike Storage Challenge From My Wife
After we installed our garage flooring and slatwall, we had several feet of unused space. We tried a couple of storage racks for bikes and nothing really worked right.
The SteadyRack Solution
I have used and written about the SteadyRack before and it has always been one of my favorite bike racks. We decided to pull out what we had and go back in with all SteadyRacks. The only thing I do not like about the product is their instructions.
How Close Are the Bikes
Because all the bike heights are slightly different and because you can swivel the bikes on the rack, we were able to mount them 16 inches apart.
How far apart can you mount a Steadyrack bike?
Steadyrack’s patented and revolutionary design helps to save more of your valuable floor space and can be mounted to virtually any wall, as close as 350mm apart. Due to the rotating/pivot action, bikes that are stored in a Steadyrack can be overlapped and when not in use, the arm simply folds away for even more space.
What colors does Steadyrack come in?
However you can customise your racks with our End Caps, which come in red, blue, green, yellow, and grey . Will hanging my bike damage the bike frame or forks.
How to store bikes vertically?
By storing your bikes vertically with a Steadyrack, you’ll be able to pivot the bikes, up to 160 degrees in each direction, placing them practically flush against the wall. This will not only save floor space, but also more space in smaller areas, which is helpful when sharing the space with a car.
Can a mountain bike fit in a bike rack?
So yes it should fit in a mountain bike rack but will be a firm fit. If you don’t want to do that you should go to the next size up to the Fat Rack. The bike will sit nicely in the rack but the front wheel may fall to one side slightly due to the larger gap, it will however be very easy to unload.
Do you need a fender rack for a bike?
If your mudguard/fender is a clip on type that isn’t connected to the front axle with metal rods then it should work fine with the Fat Rack. If your bike has conventional metal or plastic type mudguards/fenders attached to the front axle then you will need a Fender Rack.
Can a fender rack fit a classic bike?
The Fender Racks will suit exactly the same bikes as the Classic Rack except the Fender rack will also work with bikes that have fenders or mudguards, where as the Classic is only suitable for bikes without fenders and mudguards. The fat rack rear tyre rest is not large enough. Thank you for your feedback.
Does hanging a bike damage the frame?
Will hanging my bike damage the bike frame or forks. Hanging a bike in Steadyrack will not cause any damage to your wheels. If you can ride the bike, then you can also hang the bike up without causing any damage.
What is Steadyrack?
by Dave Rome. April 14, 2020. 5 minute read. Designed to hold the bike while contacting nothing but the tyres, the Australian-designed Steadyrack is one of the more innovative and popular cycling products to come from Down Under in the past decade. In addition to making no contact with the frame, rim or spokes, ...
What do you need to use Steadyrack?
Before you can use the Steadyrack you need to mount it to a solid vertical surface, aka a wall. You’ll need the usual tools for mounting things to walls: a drill, the appropriately-sized drillbit, a beverage, and fasteners tools. Yep, none of this is suitable if you’re renting.
Why do bikes swing in a 180 degree arc?
Only the tyres come into contact with the rack and from there the whole bike can be swung in an almost 180-degree arc in order to make space or to access other bikes. As an added bonus, accidentally bumping a bike will simply see the rack swing, whereas simpler hooks could see bikes fall.
How wide is a mountain bike rack?
Similarly, the smaller tyre will sit deeper into the wheel basket, and so clearance issues with some road frames can occur. This wider rack can handle up to a 3″-wide mountain bike tyre, plenty of room for everything except a fat bike (though, there’s a fat-bike specific model for this).
How big is the hole in a rack?
The mounting holes in the rack are 10 mm in diameter while the screws are smaller, giving a hair of leeway in case you drilled the holes wrong. Still, I’d like to see a slotted (oval hole) solution that provides even more freedom in case your measurements are off or the drill bit wanders.
How many holes do you need for a rack?
The installation isn’t tricky, but it’s a little involved. Each rack requires a total of four holes, with an additional two for the optional rear-wheel protector. Six holes ain’t bad, but that workload obviously grows with each rack you wish to mount.
Does Steadyrack cradle the front wheel?
It’s also worth noting that the rack cradles the front wheel in a way that even an unexpected front flat tyre won’t perturb the holding ability, something that’s not the case with other hook designs which grab the bike by just the front tyre. Likewise, there’s no chance of scratching or damaging a rim or spoke with the Steadyrack’s design.
How far apart can you install Steadyracks?
Steadyracks can be installed as close as 350mm apart and due to the swivel action, can be overlapped. When the rack is empty, the arm simply folds away.
WHY STEADYRACK?
Steadyrack offers a unique, patented bike storage solution that is easy to use and saves space. Steadyrack's can be used for your personal bike storage in your home garage, inside your living room, in a bike store, in your apartment, on your balcony or, in fact, almost anywhere you have some wall space.
How to load a bike on a bike?
Open the support arms, balance the bike on the rear wheel then use a pushing and pulling action to load and unload bikes into and out of the two support arms .
What is a Steadyrack bike rack?
Steadyrack’s wall-mounted bike racks are a unique, patented bike storage solution. They are easy to use, easy to load and unload and save space in your home or garage while keeping your bikes safe & secure.
What is the only contact with the rack when a bike is loaded?
The only contact with the rack when a bike is loaded is with the front tire.
What type of locks do you use for bicycle racks?
Bikes can be securely locked to our racks using conventional chain or D type locks.
Do you have to lift a bike rack?
No Lifting. No need to lift and juggle your bikes onto a hook, just balance your bike on the back wheel and push and it will roll up into the rack. Our racks are loved by bike riders because there is no lifting required.
