Full Answer
How to Prime a pool pump in 7 steps?
How To Prime A Pool Pump In 7 Easy Steps Step 1. Turn off the pump Step 2. Switch the multi-port valve to recirculate Step 3. Remove excess air Step 4. Clean out the pump basket Step 5. Fill the pump basket Step 6. Turn on the pump Step 7. Close the air valve
How long should I Run my pool pump?
Additionally, the faster it’ll filter through your pool water. If you’re itching for a race car of a horsepower so you can run your pump for just a few hours every day, it’s probably best to take a deep breath and consider the facts first. Horsepower is always dependent on the size of your larger pool system.
How do you Prime a pressure washer pump?
Priming the Pump by Pouring in Water Turn the multi-port valve to "recirculate.". Relieve air pressure in your filter by turning the air valve. Look for debris in the pump box basket. Pour water into the pump box and pipes. Put the lid of the pump back on. Turn the pump back on. Watch the water pump and the air valve.
What happens if you don’t Prime a pool pump?
Failure to properly prime a pool pump will quickly burn out the pump motor. It is imperative that pool owners take the time to safely and properly prime their pumps before operating them. The process is pretty simple, with the pump powered off you will remove as much air as possible and fill the system with water to replace it.
Why is my pool pump taking so long to prime?
0:144:12How To: Determine Why A Pool Pump Won't Prime - YouTubeYouTubeStart of suggested clipEnd of suggested clipYour pump will not be able to prime if there is not enough water in the pump strainer basket.MoreYour pump will not be able to prime if there is not enough water in the pump strainer basket.
How long does it take to prime a pool pump?
While the pool has been covered for the offseason, the water in the pump and lines may have evaporated or drained off. When you prime the pump, you add water to it and bleed off the air in the lines. Prime your pump anytime your pool sits for 1-2 months.
How do you prime a pool pump fast?
Steps to prime the pump:Turn pump off.Turn Cell off.Turn Filter handle to Re-Circulate (assuming you have a sand filter).Remove skimmer basket. ... Take the pump lid off and pour 4-5 buckets of water into the pump basket. ... Repeat Step 5 a few times, if necessary.
How do I get the prime back on my pool pump?
0:564:36POOL PUMP Not Priming? Here's How to Quickly PRIME a PUMPYouTubeStart of suggested clipEnd of suggested clipStep one turn on your multi-port valve to recirculate. This will direct the water into the filterMoreStep one turn on your multi-port valve to recirculate. This will direct the water into the filter head and then right back into your pool bypassing the filter. Step two remove your pool plugs.
What happens when a pump loses its prime?
No water pressure due to lost pump prime: IF you have no water pressure, absolutely no water in the building water supply piping, and no water in the water pump itself, THEN we've lost prime and the one line or two line jet pump may be unable to bring water back from the well.
What happens if I run my pool pump dry?
0:002:46What Happens If You Run A Pool Pump With No Water In It? - YouTubeYouTubeStart of suggested clipEnd of suggested clipCan cause damage to the pump. Basically what happens is that the water the water passing through theMoreCan cause damage to the pump. Basically what happens is that the water the water passing through the pump helps to keep all the parts cool and when there's no water if the pump is starved.
How do I get the air out of my pool pump line?
0:213:02How To: Bleed air out of your Pool Filter - Chlorine King Pool ServiceYouTubeStart of suggested clipEnd of suggested clipThis air big valves really good for when you enter the pump that you need to find the pump back upMoreThis air big valves really good for when you enter the pump that you need to find the pump back up all I do is we put the lid back on. You open this up again and it'll actually pull the pump leg.
Should my pool pump basket be full of water?
When working correctly, pool pumps should be completely full of water. In this guide, we discuss different tips on how to diagnose and correct the issue of a pump that is not filling up all the way. Note: This guide is meant for pool owners who are used to seeing a full pump and a half-empty pump is out of the norm.
How do I start my pool pump after winter?
0:035:14Open a Pool - Starting the System - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's time to fill up the pump. Adjust. The valves accordingly. And get it started. There's twoMoreIt's time to fill up the pump. Adjust. The valves accordingly. And get it started. There's two considerations when you're getting ready to prime your system and actually pressurize.
Why is my pool pump not pumping water?
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully 'prime' and function at full capacity.
How do you prime a pool pump uphill?
Steps to Prime Your Pool PumpTurn off the pump. ... Switch to recirculate. ... Release air. ... Clean out the pump basket. ... Fill the pump basket. ... Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on.Check the water flow to your pump.More items...
What does priming a pool pump mean?
Priming is what supplies the pump with enough water to put the water in circulation or, in other words, to start pulling water from the pool. Self-priming pool pumps automatically generate the flow of water, even if there is a lot of air in the system.
How do I start my pool pump after winter?
0:035:14Open a Pool - Starting the System - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's time to fill up the pump. Adjust. The valves accordingly. And get it started. There's twoMoreIt's time to fill up the pump. Adjust. The valves accordingly. And get it started. There's two considerations when you're getting ready to prime your system and actually pressurize.
What does priming a pool pump mean?
Priming is what supplies the pump with enough water to put the water in circulation or, in other words, to start pulling water from the pool. Self-priming pool pumps automatically generate the flow of water, even if there is a lot of air in the system.
Why is my pool pump not pumping water?
The most common reason for low or no flow is that the baskets are full of debris. By checking and emptying both the skimmer basket (by the pool) and the pump basket (inside the pump) will free up the water flow, allowing the system to fully 'prime' and function at full capacity.
How do you prime a pool filter?
0:102:01How to PRIME a Swimming POOL PUMP | Swim University - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can try adding water through the skimmers. Or you can try just adding more water to the pumpMoreYou can try adding water through the skimmers. Or you can try just adding more water to the pump housing but make sure that when you do add water to it the filter.
What is priming a pool pump?
Priming a pool pump is an essential process to get the pool area up and running. Luckily, it’s a simple task and doesn’t require thorough technical skills. All that you need is a basic knowledge of working with electrical systems. This is critical for your safety, as well as the proper functioning of your machine.
What is a pool pump?
A pool pump is just like the human heart that pumps life to the whole body. It’s responsible for carrying the water-purifying agents to the pool, renewing the water, passing it through the heater, and filtering out any debris that falls into the pool. Swimming Pool Pumps occasionally stop or malfunction, and they’re also usually turned off for ...
Why do pumps have vents?
Pumps aren’t fond of air at all. And any amount of trapped air inside them can make the whole process go haywire. That’s why you’d often find air vents in such systems to let out any trapped bubbles. Also, to facilitate priming the pump and filling it up with water.
Why does my water pump lid feel stuck?
It’s supposed to be closely screwed into place. That’s because the water should be flowing in a leak-tight system, and a wiggly cover would blow that right away. You might need to use a little tool to help you out.
Why won't my water pump start?
Usually, pumps can’t start if they don’t have enough water inside them or in the system around them. You can turn off the power and add more water to the pump, then try again.
Do pool pumps need to be primed?
Swimming Pool Pumps occasionally stop or malfunction, and they’re also usually turned off for the winter. This is true for both inground pool pumps and above ground pool pumps, in both cases, they need to be “primed” to work properly and pump water smoothly again. The presence of air or the absence of water are the two absolute no-no’s ...
What Does it Mean to Prime a Pool Pump?
A pool pump often gets pockets of air trapped inside. Anytime that it is not operating full of water such as when the pool is closed down or re-opened for the season , there is a potential to get air inside the pump.
How long does it take for a water pump to run?
Check the water flow to your pump. Water should be consistently flowing within thirty seconds. If you do not have a consistent flow, turn the pump back off and repeat the previous steps. Thoroughly check all of your hardware for wear and tear.
Why is my pool pump not priming?
Your pump needs an adequate water supply in order to create enough suction to get things moving. Low water levels in the filtration system , either from a leak or insufficient fill, are typically the cause.
How to recirculate pool water?
Switch to recirculate. The multiport valve on your pump can be set to recirculate the water. This will bring water directly into the pump and then recirculate it back out into the pool. In the recirculate setting, the water bypasses the filter and goes directly into the pump to ensure that there is in fact, water in the pump.
How to get water out of a water pump?
Fill the pump basket. Use a garden hose to slowly fill the pump basket and put the lid back in place. Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on. Check the water flow to your pump. Water should be consistently flowing within thirty seconds.
Why is it important to keep a pool pump working?
Keeping your pool pump functioning is essential to maintaining a clean and healthy swimming pool. And, by extension, knowing how to take care of your pool pump is also crucial so that you can avoid costly repairs and replacements.
How much does a pool pump cost?
Most pool pumps cost several hundred dollars. It is an expense that is necessary to maintain a swimming pool, but not one that you would want to invest in frequently or unnecessarily. Priming your pool pump is a prudent step that you can take to make sure you are not accidentally operating the pump dry.
How to get water out of a water pump?
Turn on the pump. Open up the air valve and turn the system back on. This should have gotten the water flowing, but if you don’t see it flow through the basket within a minute or so, turn the pump off and repeat the process. Step 7. Close the air valve.
Why do you want the lines from the skimmer to the pump to be full of water?
What you want here is for the lines from the skimmer to the pump to be full of water in order to create suction.
How to fix a broken O-ring on a pump?
Clean out the pump basket. Remove any debris or silt that might have accumulated in the pump basket and rinse out with a hose if necessary. Also check it for any cracks or damage to the O-ring. If playback doesn't begin shortly, try restarting your device.
Do you need to prim a pump before turning it on?
While some newer pumps have self-priming functions, most pumps require priming before turning it on to get the air out of the system and get the water flowing through it.
How Long Should It Take to Prime a Pool Pump?
If you look at the steps involving priming a pool pump, they are not very technical or time-consuming. However, if you do not see water flowing in the strainer after you turn on the pump, you may need to repeat the steps and that can take up a lot of time.
Why Should You Prime a Pool Pump?
When it comes to the pool pump, it is an unusual piece of pool maintenance equipment. While almost every other pool maintenance equipment works best when it is submerged in water, a pool pump is meant to function only when there is water inside the pump.
What is a Pump?
A pool pump is like the heart of the pool’s filtration system. Consisting of several parts, such as pump housing, impeller, strainer basket and a motor, the pool pump creates water movement.
Why Isn’t My Pool Pump Priming?
As mentioned earlier, pool pumps are there to ensure that you can enjoy a clean and beautiful pool every time you are ready to dive in. However, when a pool pump does not prime correctly, it can result in a disaster that most homeowners seldom expect.
Why is my pool pump vacuuming?
When air is trapped in the pool pump chamber or in the water line that intakes the pool water, it creates a vacuum, which makes it difficult to circulate the pool water through the filters and back to the pool .
When you turn off the diverter on the suction side, you select whether the pump will pull water from the?
When you turn off the diverter on the suction side, you select whether the pump will pull water from the skimmer or the main drain. This step ensures efficiency of the priming process.
Do pool pumps have to be self priming?
Most of the pool pumps available on the market are self-priming, which means that they will automatically circulate water when you turn them on and create a vacuum that will initiate and sustain a suction strong enough to pull the water out of the pool and then push it back to the pool through the water return line.
What is the yellow dial on an Intermatic pump?
The most common and oldest style of Intermatic timer is commonly referred to as a yellow dial timer. On those types of timers if the dial pointer is directly over the “off” lug it can prevent the tab hanging down from fully moving to the Right when a user attempts to turn on the timer manually for the pump to run.
Can you adjust the water flow in a spa?
If you have a SPA you can adjust the water flow to suck from the SPA drain. (Make sure to change the valve back to the correct position once you are finished either attempting or priming the pump. This can be very helpful if the spa and or the equipment is elevated above the pool water level.)