Vermiculite Calculator
| Example | |
| Chimney Depth (Metres) | .325 |
| Liner Diameter (Metres) | .150 |
| Required Volume of Insulation (m3) | |
| Number of Bags Required |
What is the ratio of cement to vermiculite?
The ratio is 2 bags of Vermiculite to 1 bag of cement. The Vermiculite and cement go into the mixer and then you’ll add about two and a half 5-gallon buckets of water, until you reach an oatmeal consistency that you can trowel easily.
How much does a bag of vermiculite weigh?
Vermiculite is sold in a common size of 4 cubic feet, and you may be surprised at how light it is . Portland cement comes in 94 lb bags, and you may be surprised at how heavy these are! If storing your product outside, be sure to wrap it tightly with plastic or tarps, to keep any rain from touching the bags. How is Pool Floor Vermiculite Mixed?
Where can I buy Pool vermiculite?
The easiest place to get the pool vermiculite you’ll need would be from In The Swim. We have 28 lb bags for about $1 per pound, with free shipping.
Where can I buy a paddle mixer to mix vermiculite?
Vermiculite is mixed on site and in a cement mixer called a paddle mixer, which can be rented at any rental shop. You will need Portland cement on hand to complete the mix.
See more
How thick should vermiculite pool bottom be?
between 1 and 2 inches thickAs with concrete, crews should make the vermiculite layer between 1 and 2 inches thick. Any thicker and it will void the porosity, which would defeat its purpose. Fans of this material also claim that it's easier on the liner.
How many bags of pool krete do I need?
One bag of Pool-Krete covers approximately 10 square feet. The recommended thickness of the Pool-Krete should be between 1-1/2" to 2". The accuracy of the excavation will determine the number of bags of Pool-Krete needed for the job. If the hole is cut too deep or too large the requirements will increase.
How much does pool vermiculite cost?
This vermiculite pool base aggregate is often used by pool contractors, along with industrial and commercial businesses. Priced per bag. 30 $20.950 ea.
Can you mix vermiculite with cement?
Mix proportions vary between 4:1 and 8:1 vermiculite aggregate to cement by volume, depending on the use for which the product is intended and the method of manufacture. The water content should be only sufficient to provide adequate plasticity in the mix.
How do you vermiculite a bottom pool?
The ratio is 2 bags of Vermiculite to 1 bag of cement. The Vermiculite and cement go into the mixer and then you'll add about two and a half 5-gallon buckets of water, until you reach an oatmeal consistency that you can trowel easily. Leave it in the mixer for about 20-30 seconds and that should do it.
How do you fix the bottom of vermiculite in a pool?
2:444:41Concrete Pool Floor repair for Vinyl Liners - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a one part portland cement to one part sand mixture. So that way it's easier to sand off yourMoreUse a one part portland cement to one part sand mixture. So that way it's easier to sand off your edges with a masonry sanding block when you're finished.
How thick should a pool bottom be?
To be structurally sound, a concrete pool shell should generally be 6 inches thick. Depending on the engineer and the soil condition, it may be more. (On top of that, the plaster interior finish should be at least ⅜ inch thick.)
Can it rain on vermiculite?
Although Pool-Krete® should not be used during a rain, there will be occasions when the weather simply rolls in quickly during installation. If possible, cover the pool area with polyethylene. A light mist will generally not affect the Pool-Krete®.
What happens if vermiculite gets wet?
Vermiculite insluation itself does not burn: it is non-combustible, though contaminants and debris, if mixed with any insulating material at enough volume, might burn. When wet, vermiculite can hold a lot of water, as much as 220-325% by weight, and as much as 20-50% by volume.
How is vermiculite applied?
Exfoliated vermiculite is added to a calcium silicate slurry. This is then dewatered by pressing or by using one of the Fourdriner/Magnani/Hatschek processes to form a flat board which is then heat cured under pressure (typically 10–15 bar) for periods of up to 24 hours.
How thick should a vermiculite pizza oven be?
Vermiculite's ability to insulate plays an important role in such ovens. In order to maintain a high temperature within the oven, the vermiculite and cement mix must be moulded around the outside of the domed oven wall at a thickness of at least 4 inches.
How much perlite Do I need to make a pizza oven?
0:408:27EASY PERLITE OVEN - Part 2 - Building the oven tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then two parts water but what we'll do is we'll do all the dry ingredients first mix them up andMoreAnd then two parts water but what we'll do is we'll do all the dry ingredients first mix them up and then add the.