How to use an ion Auger on Ice?
The core temperature needs to be about 40 degrees. When you take the auger out on the ice and after you drill the first holes, take the battery off and put it in your pocket or in a heated ice shelter or vehicle. Then when you want to make another bunch of holes, the ION should work just fine.
How many holes should you drill when ice fishing?
Ice fishing can be an active sport if you move a lot, but if you do not move as much as others then you won’t be drilling many holes. Most anglers drill up to 20 holes per day averagely. If your requirement is less than this number, then even a manual auger would be good enough.
What size Auger do I need for ice fishing?
With enough power to turn either an 8″ or 10″ auger bit with ease, it is the ideal ice fishing solution for anglers wanting to spend more time fishing and less time fussing with a noisy, struggling machine.
Are electric augers good for holes?
Electric augers are no doubt very handy, but they may not always be the best option. The performance of an electric auger mainly depends on the charge and battery power. In extreme cold, holes close up fast and re-opening holes become a task.
How many holes can you drill with electric ice auger?
It comes standard with an 8” blade that is perfect for many species of fish. It's rechargeable battery is good for 50 holes (16 inches of ice), plenty of power for a day on the ice.
How strong of a drill do I need for an ice auger?
For a convertible ice auger to work properly, your drill needs both speed and power. 500-750 RPM is really a sensible no-load minimum; any lower, and you're just not going to spin the blades fast enough for optimal performance. It's hard to get too much torque (as long as you're using a side stabilizing arm).
How long does an ion auger battery last?
Typical cycle life of a good quality designed Li-Ion battery pack like a 40V or 24V Strikemaster product is around 500 FULL charge and DISCHARGE cycles. I would not be surprised to see packs run 10 years depending on usage.
Is a 6 or 8 ice auger better?
For gas and electric augers, the best overall size is the 8-inch auger. It's a large enough hole for most fish, and you can drill overlapping holes for a larger hole. For hand augers, a 6-inch auger would be the best overall size for cutting through the ice if you're drilling numerous holes.
What kind of drill should you use for ice auger?
DEWALT 20V MAX XR Hammer Drill Kit The DEWALT 20V deserves to be called one of the best cordless drills and is the best DEWALT drill for ice augers. It's one of the fastest models on this list with three operating modes to choose from, including drill, hammer, and driver.
What size cordless drill do I need for ice auger?
1:084:28CORDLESS DRILL Ice Auger Requirements and Settings. What ...YouTubeStart of suggested clipEnd of suggested clipSo you want 5 amps or higher this is a 9 amp. This is as big as i can go with the octane. The nextMoreSo you want 5 amps or higher this is a 9 amp. This is as big as i can go with the octane. The next thing you need is you need a drill with 750 inch pounds of torque or. More.
Does Eskimo own ion?
In addition to the Eskimo and Ion brands, Ardisam also owns Barronett Blinds, Castle Pellet Stoves, Earthquake Groundbreaking Power Equipment, Gazelle Tents, Rivers Edge Treestands, Yardbird Chicken Plucker, Yukon Tracks, and Yutrax ATV Accessories.
How long does it take to charge an ion ice auger battery?
The battery takes between 2-3 hours for a full charge, but can sit on the charger overnight if needed. He did recommend not keeping the battery on the charger for more than 24 hours, however.
How do you keep ice auger batteries warm?
0:342:22Keeping Auger Batteries Warm on the Ice - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat I have here is an insulated growler or thermos. And I put boiling water in it this. Morning.MoreWhat I have here is an insulated growler or thermos. And I put boiling water in it this. Morning. Basically put it in this cooler with my batteries. And it's keeping everything warm all day.
Is an 8 inch ice auger big enough?
Ice fishing holes range in size from 6 to 12 inches in diameter. The ideal hole size is 8 inches. An 8 inch hole is big enough to pull most fish through while also being easy enough to drill with a hand powered ice auger.
How far apart should ice fishing holes be?
Here's the quick answer: If you're fishing next to someone else on the ice, your holes should be at least 5-6 feet apart to avoid fish getting tangled in each other's lines when you pull them up. If you're using a camera for ice fishing, the hole for the camera should be at least 2 feet away from your fishing hole.
How deep is an ice fishing hole?
4-6 inch ice depth = 6-8 inch hole. 6-18 inch ice depth = 6-10 inch hole. 18-24 inch ice depth = 8-12 inch hole.
Can you use a brushed drill for ice auger?
Brushless motor: Although you can often get by with an older brushed-motor drill, you want to go brushless. The augers work the drill motor hard, and brushless motors won't get damaged by overheating as easily.
Can you use a hammer drill as an auger?
A hammer drill is really intended for drilling through concrete. It is used in conjuction with a special bit to hammer or chip the concrete. If you bought one of those adapters to run with an auger blade, I would not use a hammer drill.
Do hand drill ice augers work?
0:003:02Cordless Drills for Ice Augers (Overview) - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then I use my camera with both hands. And then as I can wrap up the revolutions are beautifulMoreAnd then I use my camera with both hands. And then as I can wrap up the revolutions are beautiful because now I can reel up and I don't have a bunch of line out. And I'll walk to the next hole.
How well do drill ice augers work?
A manual ice auger with sharp blades easily cuts through 6-8 inches of ice like butter in under 10 seconds. Drilling a hole in ice 10-18 inches thick using a hand auger is significantly harder and will take at least 30 seconds of hard work for each hole. Avoid manual ice augers for ice thicker than 18 inches.
How long does it take to warm up a battery pack?
Yup, you warm them up and they work. Of course warming a battery pack is far from a quick process. From my experience you should plan on 30+ minutes, minimum, to get one warm enough in an ice house to make a difference. Longer to get it back to what I would consider a fully operational state. It is the battery and not the motor. If you pull a cold-dead battery out of the auger and put in a warm one you’re back in the game.
What happens if you leave a battery out in the cold?
But if the battery is left out in the cold on the auger for a couple hours and then try to use it, it will start to drill and roughly 5secs in will cut off. . This means the battery is dead due to the cold.. What this means is you have to remove the battery and lug the brick around in your pocket while not in use.
What temperature should a battery be kept at?
We have found (after the video was made) that the battery must be kept warm. The core temperature needs to be about 40 degrees.
How to make sure battery is fully charged?
Make sure your battery is fully charged by leaving it on the charger in the house or heated garage overnight.
Can you replace a gas auger?
The idea is a good one for those looking for an auger to punch a limited number of holes. They’ll never replace gas augers but there is a market for this type of product. From what I’ve seen there’s some serious R&D yet to be done before I’d consider a Li powered auger ready for wide spread use.
Can you remove a battery and stow it?
As for the battery issue you can always remove it and stow it somehow to keep it warm. Maybe use a thermal bag and heated hand packs?
Do you have to push a switch before you can depress the trigger?
There is a switch that you have to push in before you can depress the trigger. It also has a delay before it starts.
How to determine if a drill is good?
There are two parts to the drill equation. First, it has to generate enough torque to spin the auger blades at an RPM that the drill likes. Not enough torque and it slows down and generates heat in the motor. That's how they burn up. Second, and likely most important, you need a battery with enough Amp/Hour capacity to keep the drill working under load and drilling holes. Amp/Hours are a measure of reserve energy and the more the better. Some of the newer drills are generating over 700 inch lbs of torque and come with 5 Amp/Hour batteries.
How to keep ice auger from dropping down hole?
Just Google ice auger drill adaptor and you will find them. Be sure to use a lanyard or some other protection to keep the auger from dropping down the hole if it comes out of the chuck. Let the auger blades do the work and do not push down.
How much torque does a Nils 6" have?
With a regular Nils 6" I'd feel better having 600 in ft of torque.
Can bobcats move through oak leaves?
Yup! That even though they’ll bark occasionally at me, they’re really NOT worried! 😄 And that a bobcat can move through oak leaves without making hardly ANY noise. That was impressive.
Do you need moderator approval for a post?
Note: Your post will require moderator approval before it will be visible.
Do you need to sign up for FM?
If You want access to member only forums on FM, You will need to Sign-in or Sign-Up now .
Who makes the adapter for Nils?
Ice Master makes an adapter for Nils.
What is the best auger for ice fishing?
Trophy Strike’s 107309 ice auger is one of the best augers for ice fishing out there. It has plenty of features and comes with a battery large enough to keep them running. Trophy Strike claims that this little power machine can drill up to 96 holes in 20-inch thick ice on a single battery life, which is way more than what you need on a single ice fishing trip.
How many holes do you drill in ice fishing?
Most anglers drill up to 20 holes per day averagely. If your requirement is less than this number, then even a manual auger would be good enough.
What is an auger powerhead?
Landwork’s electric auger powerhead is an exceptional machine that is powerful and strong. Buying this powerhead allows the users to choose a custom auger bit according to their needs, making it a flexible choice to be used on both land and ice. Moreover, the powerhead offers plenty of features that make drilling anywhere effortless.
What is a strikemaster auger?
The StrikeMaster Lithium 24V Lite-Flite auger features an electric DC brushless motor that powers this lightweight auger. It ignites more quickly than other tools and allows for reduced battery drain.
What is an ion 33405?
Ion 33405 is a compact battery-powered ice auger that is not just lightweight and easy to use but is also powerful and highly reliable. One can easily make a hole as large as needed and can then simply put the machine away. Ion 33405 greatly simplifies your digging process so that you can focus more on ice fishing and not on holes.
How many inches of drilling power does the R1 Auger have?
The new R1 Auger gives you a 5 Ah Gen 1 Battery (better than the old ION) that gives you 1600 inches of drilling power.
How many inches of ice can an auger cut?
This electric auger comes with a high power 40V Max Lithium-Ion battery that can cut through 1000 inches of ice on a single charge, and Ion reverse feature that flushes the excess slush down the hole, removing the need for a skimmer.
