How big of a tractor do you need to run a round baler?
The low horsepower round balers, like the 450E, 450M, and 550M models can be paired with any of the John Deere 5-Series or 6-Series utility tractors. The MegaWide models that require a minimum of 125 PTO HP need to be paired with a more heavy duty tractor like a 4WD or Row Crop tractor.
How much horsepower does a 4x5 baler have?
Now you can bale on your schedule when crop and weather conditions are right450 UtilityTractor RequirementsPTO HP, minimum40 hpPTO Speed540 rpmHydraulic Remotes1 (2 w/hyd. pickup lift)13 more rows
How much horsepower do you need to run a big square baler?
Key SpecsBale80x90 cm 3x3 ftMachine - Width2.76 m 9.1 ftMachine - Height2.7 m 8.9 ftMachine - Weight7,700 kg 16,975 lbMinimum tractor requirement86 kW 115 PTO hp - no Pre-Cutter 97 kW 130 PTO hp - with Pre-Cutter5 more rows
What size Bale does a John Deere 535 round baler make?
The John Deere 535 is a pull-type, 540 rpm PTO driven baler with a variable cylindrical chamber and a drum pickup. The 535 baler produces hard core bales measuring 5.1 ft (1.6 m) wide and 1. 2. 3.
How much HP does a 4x4 round baler need?
PTO horsepower requirements for round balers start at 30 hp and can run up to 120 hp.
What HP tractor do I need to bale hay?
35 horsepowerMost standard square balers on the market require 35 horsepower at your tractor's PTO, and a minimum tractor weight of around 3000 pounds.
What factors should you consider when sizing a tractor to the baler?
Horsepower, Weight and Safety.
How much does a New Holland 590 baler weight?
0.50000 lbsWeight0.50000 lbsDimensions12 × 12 × 3 inModel590 / 590C / 595 / BB940 / BB960 / BB9050 / BB9060 / BB9070 / BB9080 / 230 / 330 / 340BrandNew Holland
How wide is a John Deere 435 baler?
John Deere 435 DimensionsDimensionsWheelbase85 inches 215 cmWidth85.75 inches 217 cmHeight71.5 inches 181 cmShipping weight3,750 lbs 1701 kg1 more row•Jun 13, 2022
How long are the belts on a John Deere 535 baler?
DescriptionBelt QTYBelt WidthBelt Length47”524”47”529”
How do you load the net wrap on a John Deere 535 baler?
0:271:21It over itself roll it over a couple times like you're making a piece of rope. Take your thumb pushMoreIt over itself roll it over a couple times like you're making a piece of rope. Take your thumb push that right up in between the rubber and still roll.
How much PTO HP do I need?
Remember, you need to match the tractor to the job you want to do. If you want to operate a five-foot cutter (shredder), a good rule of thumb is 20 PTO horsepower (not engine horsepower). A six-foot cutter requires roughly 30 PTO horsepower.
How wide is a John Deere 336 square baler?
Call UsKey Specs:Pickup width187.9 cm 74 in.Bale sizeHeight x width 36x46 cm 14x18 in. Length 30.5 to 127 cm 12 to 50 in.Adjustable Hydraulic Bale DensityOptionalPlunger - Strokes/minute80 spm54 more rows
What size round balers are compatible with John Deere?
The low horsepower round balers, like the 450E, 450M, and 550M models can be paired with any of the John Deere 5-Series or 6-Series utility tractors. The MegaWide models that require a minimum of 125 PTO HP need to be paired with a more heavy duty tractor like a 4WD or Row Crop tractor.
Can you match a tractor to a baler?
Matching your tractor to a baler it can power is critical, but there are other important specs to consider. From bale size to wrap compatibility, choosing the right baler for your needs comes down to a number of different factors.
What could make stopping a problem going down hill with a light tractor?
bale in the chamber could make stopping a problem going down hill with a light tractor.
What horse is used for Gehl 1500A?
I ran a Gehl 1500A 5x5 with a 53 horse Oliver 1550 if that helps you. It handled it as well as a larger tractor.
Do hard core dry hay bales take a lot of HP?
Hard core dry hay bales don't take a lot of HP. Making wet haylage bales is a bit of a different story. while climbing hills. And on hilly ground you are also better off using a bigger heavier tractor while. baling on a down hill side, as you will need to stop the tractor and baler to tie and eject the bale.
Can you use a tractor on hilly terrain?
while climbing hills. And on hilly ground you are also better off using a bigger heavier tractor while
Can a JD 635 run with a 185 Allis?
We ran a JD 635 with a 185 Allis with no problem, we have also ran the same baler with a 175 Allis but it was a bit light on hills, worked fine on flat ground. So I would say you need to look at more than just HP but weight of the tractor, type of ground.
Can I use a 3020 gas baler with a 510 round baler?
I baled with my 3020 gas this summer on a JD 510 round baler. It did just fine. Normally I use the 4020 but it was down at the
How much HP does a JD 3366 baler need?
The manual for my JD 3366 baler recommends 35hp minimum. I know my 'Bota m7040 doesn't have any problems with it. (68 net hp, 62 @ the pto per the manual.)
How many horses are on a 6060 baler?
It will for sure teach you how to count strokes. You can feel each stroke. I now pull that same baler with a AC 6060 which has 59 horses on the PTO. The big advantage is it has a deck you sit on not straddle the transmission.
How much horsepower does a 5070 hayliner have?
I run a NH 5070 hayliner with 70 horsepower and you know it's back there on the hills around here.
How much horsepower does a NH 316 have?
My NH 316 manual says minimum horsepower is 35hp. I pull it with a JD 2755 that is around 72 hp on the pto. I can't imagine pulling with anything less. I can feel the plunger on every stroke. Depending on cash flow whether you can afford two tractors, one with a little more hp for the baler and the other for raking and maybe cutting, depending on the mower.
Does a Ford 601 work?
We have ford 601, Works great to Ted, and move wagons around. We did put a new exhaust on it to point up instead of under. Thinking that dry hay and exhaust gathering dry hay wasn't a good combo.
Can you bale with an 8N Ford?
I don't think you would want to bale with an 8n ford because it does not weigh that much and you will Definately feel every stroke of the plunger and will make for a very rough ride. The other thing is a 8n ford does not a live clutch and while it can be done I would certainly not want to bale with a tractor that does not have a live clutch.
What is the best hp for a Deere round baler?
If you are buying a baler first, keep horsepower requirements in mind when pairing with a tractor. The 45-115+ PTO hp range is best suited for pulling Deere round balers.
What to consider when selecting a John Deere baler?
One of the last things to consider when selecting the John Deere baler that’s right for you is the number of available features. It’s important to review the capabilities of each model and decide if you want a low-spec baler with less features or a high-spec baler with more features.
What baler do you need for silage?
If this is going to be the primary type of hay you’re cutting, you may want to consider a Silage Special Round Baler, which includes a number of features to put up high-moisture forage. However, there are other model options available that might better suit operators that work primarily in dry conditions. You will also want to consider if you want your bales pre-cut, as this will help narrow the selection process even further.
Does John Deere balers have B wrap?
One of the most unique options available with John Deere’s balers is B-Wrap compatibility. This technology is dubbed as Deere’s “alternative to indoor storage,” as it allows producers to protect their hay crop from rain and snow, while also reducing ground moisture. Be sure to consider which Deere models are equipped for netwrap in your selection process if this is something you might be interested in having on your farm.