how much does a commercial beer tap system cost

How much does a commercial beer tap system cost? Overall, these 12-tap systems typically start at $4,000 ($5,500 including glycol) and can cost as much as $12,000 for more deluxe models. As a general rule of thumb, you should expect to pay about $1,000 per beer line. This cost includes a long run, blended gas, and glycol.

Full Answer

How much does a 12-tap beer system cost?

Mar 22, 2020 · How much does a commercial beer tap system cost? Overall, these 12-tap systems typically start at $4,000 ($5,500 including glycol) and can cost as much as $12,000 for more deluxe models. As a general rule of thumb, you should expect to pay about $1,000 per beer line. This cost includes a long run, blended gas, and glycol.

Are foam on beer prevention taps worth it?

Click to see full answer. Regarding this, how much does it cost to install a beer tap? Overall, these 12-tap systems typically start at $4,000 ($5,500 including glycol) and can cost as much as $12,000 for more deluxe models.As a general rule of thumb, you should expect to pay about $1,000 per beer line. This cost includes a long run, blended gas, and glycol.

How much does a beer line cost to run?

Overall, these 12-tap systems typically start at $4,000 ($5,500 including glycol) and can cost as much as $12,000 for more deluxe models. As a general rule of thumb, you should expect to pay about $1,000 per beer line.

How much does it cost to build a beer tower?

Overall, these 12-tap systems typically start at $4,000 ($5,500 including glycol) and can cost as much as $12,000 for more deluxe models. As a general rule of thumb, you should expect to pay about $1,000 per beer line.

How much does it cost to install a tap system?

How much does a beer wall cost?

How much does a glycol system cost?

How much does it cost to install a beer tap at home?

How much does it cost to install a keg?

How do you set up a keg at home?

How is beer kept cold in a glycol draft system?

What is a glycol system for beer?

How does a glycol cooling system work?

Do bars use Kegerators?

How do you keep beer lines cold?

How do bar taps work?

How many taps are needed for a keg?

It takes up a lot of room behind the bar since you’ll need a giant cooler to hold all of your kegs. Typically, 6 taps is the upper end of the capacity for kegerator systems. Smaller kegs are often used instead of standard half-barrel kegs, requiring them to be changed more frequently.

What is an air cooled beer system?

An air-cooled system using kegerators is one of the simpler draft beer system options you can use in your bar. It offers the following advantages: Simple system that is easy to install and operate. You have a shorter run since the beer is kept right below the tap. There are also several drawbacks to using this system:

What is a turbo tap?

Turbo taps – Turbo taps are very long taps that dig deep into the beer glass. When filling a beer, the turbo tap extends all the way to the bottom of the glass, causing the beer to pour onto itself. This allows you to fill a beer much quicker.

What is the best way to keep draft beer cold?

Depending on your bar’s unique needs, you may want to consider purchasing some of the following add-ons to your draft beer system: Glycol-dedicated cooling system – Using a glycol cooling system makes sense in almost all situations since it’s the most effective way to keep your beer cold.

How much does a chiller tower cost?

The tower will cost about $2,000 for 12 taps, and the drip tray will run approximately $200. Glycol chillers start at $1,000 and can cost as much as $5,000 depending on the length of the run of the lines (this is dictated by the distance from the walk-in to the tap handles). A longer run will require more and stronger pumps, which increases the cost of your cooling system.

How much does it cost to buy a coupler and regulator?

Couplers (to attach the line to the keg) Regulators (to regulate the pressure forcing the beer out of the line) If you need to purchase couplers and regulators separately, they’ll cost you approximately $30 per coupler and $50 per regulator. You’ll also need to purchase a tap system to use with your kegerator.

What is a glass rinser?

Glass rinsers – These are used to spray clean water into the glass to ensure it’s properly cleaned and doesn’t have any residual cleaning fluid in it before pouring a beer. These are a common add-on for bars that serve a large selection of craft beers on tap.

What are the three systems that are available for a new tap system?

The three systems we’ll be diving into are: the kegerator, direct draw, and long draw tap systems .

How much does a kegerator cost?

On the lower end, a single faucet, single keg kegerator runs about $600, while an eight-tap prefabbed system will hit its highest price point around $8,000.

How much does a long draw cost?

The long draw will typically run $1,200 per tap, which doesn't account for the cost of the glycol for the lines or the additional charges for line length. With a long draw, your kegs are stored remotely from the bar and run along glycol lines to the taps; the glycol keeps your beer cool throughout the journey. The longer the distance from the cooler to the tap handle, the more the lines will cost at the outset, at a cost of roughly $12 per 60 inches of hose and then $15 per foot for trunk line, which holds everything together.

How much does a direct draw system cost?

With a direct draw system, you’re looking at spending about $1,000 per line , which doesn’t include the price for installation. A tap tower alone can range from $1,000 to $2,500 for an average number of taps (think 7 to 12). And with each additional faucet, the price goes up. A drain tray is also necessary, so you’re looking at another $200 to $800, depending on how fancy you want to get. Before you’ve hired a crew to install, you’re already spending $7,000 to $13,000 on hardware, with the loaded expectation you have a cooler sharing a wall with the bar.

How many venues use Untappd?

More than 20,000 venues around the world use Untappd for Business for menus, analytics, and promotion of their venue. Schedule a demo or start your 30 day free trial – no credit card required.

Can a kegerator hold sixtels?

That limitation is based on the space available inside a particular kegerator. Rather than a half barrel keg, these will likely hold sixtels or pony kegs, so they need to be changed more often. Additionally, these systems often look less professional than direct draw and long draw tap systems.

Do kegerators work for cold storage?

The kegerators and long draws can essentially work for any location, but you’ll need to weigh the pros and cons of each. The direct draw will only work for select locations where the cold storage lines up to the bar just right.

WHAT ARE THE ADVANTAGES OF GLYCOL SYSTEMS?

The primary advantage of glycol systems is that they offer a very reliable method of delivering beer. From the walk-in cooler to the dispensing faucet, glycol draft beer systems are capable of impeccably controlling the quality of the beer over long distances.

A WORD ABOUT WALK-IN COOLERS

To ensure profitable draft beer, a dedicated walk-in cooler is mandatory. As I detailed in another post (reference below), don’t make the mistake of placing case beer and keg beer in the same walk-in cooler.

HOW MUCH DO GLYCOL DRAFT BEER SYSTEMS COST?

You can’t enjoy all the above benefits with any other type of draft beer system. Of course, glycol systems are a little more expensive.

What is the trunk line of a draft beer?

If the power pack is the heart of the draft beer glycol system, then the trunk line is its blood vessel. The trunk line itself is a bunch of beer lines (usually, from 4 to 10) sandwiched around a pair of glycol refrigeration lines all of which are wrapped in foil and bound together with some insulation on top.

Where is the glycol line in a beer tower?

One glycol line is outbound extending from the power pack to the beer tower while the other returns from the beer tower back to the glycol power pack.

How does a power pack work?

The power pack pushes refrigeration (glycol) through the center of the trunk line. The trunk line contains up to four glycol lines: 1 outbound glycol line (s) (runs from the power pack to the tower) 2 return glycol line (s) (enables the refrigerant to complete the cycle and become re-chilled)

Why do draft beer systems use propylene glycol?

This is done mainly to prevent the foam buildup as the beer travels from point A (storage) to point B (draft tower). Glycol draft beer systems use propylene glycol as the cooling agent (hence, the name). Glycol itself is a colorless, odorless, slightly syrupy chemical compound that is a bit thicker than water.

How hot is a draft beer cooler?

The ultimate goal of the whole glycol draft beer cooling system is to transport the beer from the walk-in cooler over a significant distance to the beer tower while maintaining a constant beer temperature of 36-38 degrees Fahrenheit (2-3 degrees Celsius).

What is the lever on a glycol chiller?

The easiest-to-explain part of the glycol beer chiller system since it’s the only element that’s “on the surface”. Beer lines are attached to a shank or faucet that’s inside the beer tower. All you have to do then is pull the lever called “tap handle” and pour some fresh, cold beer.

How does a beer tap system work?

This system works by using a beer trunk line that connects the beer tower to where kegs are being stored, which can be anywhere on the property. Remember beer can be dispensed up to 800'. The downside with this type of beer system is that it's usually more expensive overall. However, it allows the owner to dispense beer anywhere and as much as they want.

How much beer can you dispense?

Remember beer can be dispensed up to 800'. The downside with this type of beer system is that it's usually more expensive overall. However, it allows the owner to dispense beer anywhere and as much as they want.

What is the best material for beer dispensing equipment?

I'll save you the frustration and spending money on inferior products by sticking with stainless steel. This goes for all parts that are in contact with beer. Equipment such as beer couplers, beer shanks, faucets, and hose fittings. Stainless is more sanitary and the equipment will last a lot longer. So do yourself a favor and stick with all stainless steel dispensing equipment.

What is direct draw beer?

A direct draw system is the most common beer tap system that you will find in a bar. This is because it has many different benefits and can be changed to suit any business needs. When this type of system is used, all kegs are stored inside a beer cooler. This is also one of the most popular beer systems to work with.

Why do establishments have less than 20 beers?

Offer a good choice of options. When you have less than 20 beers on tap, it's usually because the establishment has a very specific beer menu. There are many factors that go into determining how much beer to serve. The number of seats, the size of your establishment, ...

Why do you clean beer lines?

This ensures the beer being poured from the beer taps is nice and clean. Another benefit of cleaning your beer lines is it will actually help the beer pour better. This is not something to cut corners on because if you neglect your beer system it will result in pour tasting beer and cost you money.

Can you tap 2 kegs in a keg stacker?

Keg Stackers allow owners to tap 2 kegs in the place of one, and are ideal for smaller spaces where keg racks would take up too much space. Keg stackers are also a much cheaper alternative to keg racks.

What to consider when choosing a beer system?

Consider your space and the role beer plays on property. This will help determine which system is best for you.

What is remote beer delivery?

Remote systems deliver beer through chilled lines and are common in bigger facilities, restaurants, and breweries. Usually these properties will have one main beer cooler or a few and need to send beer to different bars on property.

What is craft beer?

Craft beer's exactly that—a craft. Having the right temperature, level of carbonation, and restriction set up in the system will make beer pour perfectly.

What is the best mix for nitro beers?

It’s a mixture of Nitrogen and C02. For Nitro beers, a proper mix of 70 percent Nitrogen to 30 percent C02 is ideal for Nitros, draft wines, and coffee.

Why is draft beer important?

A quality draft beer setup's enough reason for folks to return to an establishment . Having a quality draft beer system keeps you competitive with other beer serving businesses. While offering customers a great experience.

How far away can you pour beer?

I’ve personally installed beer systems pouring beer over 600 feet away and worked on one approaching almost 800 feet.

Is commercial beer a good investment?

Commercial draft beer systems are a smart investment in your business.

Cost of A Simple 6-Tap Air-Cooled System Using Kegerators

See more on blog.bar-i.com

Cost of A 12-Tap System

Optional Add-ons to Your Draft Beer System