How much does a paved driveway cost in Ontario?
Asphalt / blacktop driveway Asphalt driveway paving costs $3 to $7 per square foot or $1,800 to $4,200 on average for a 600 square foot two-car driveway.
How do you calculate the cost of an asphalt driveway?
For the simplest estimate, you can use this formula.Length x width=Square footage of the driveway.Driveway sq ft x $3= low end cost.Driveway sq ft x 7= high end cost.Driveway sq ft x $2= low end cost.Driveway sq ft x $4= high end cost.When to reseal your driveway:When to repave your driveway:
Which is cheaper a concrete or an asphalt driveway?
The cost of an asphalt driveway is typically cheaper than concrete, costing $2.00 – $4.00 per square foot. Asphalt prices tend to fluctuate with fluctuations in crude oil prices. In contrast, a concrete driveway costs between $4.00 – $6.00 per square foot for a standard installation.
How much does it cost to asphalt a driveway in Canada?
The Basics The costs for asphalt will certainly fluctuate based on a variety of factors such as thickness, type, and consistency. However, asphalt tends to be priced by the square foot, with prices ranging anywhere between $3 and $5 per foot.
How much is a 700 ft driveway?
For a larger driveway or thicker base, the cost will be higher. For example, a driveway 15 feet wide by 700 feet long with a six inch base will need approximately 25 tons of gravel, at a material cost of about $700. With delivery, the total cost will be around $1000.
How much is a ton of asphalt in Ontario?
On average, the asphalt paving costs estimate for materials ranges between $100 to $200 per tonne. One ton covers between 40 to 80 square feet.
Is asphalt the same as blacktop?
Blacktop is heated to approximately 150 degrees celsius, whereas asphalt is only heated to 120 degrees celsius. Asphalt is has a higher bitumen content and for that reason is less porous and more resilient to wear and tear from high traffic and thus is the preferred choice for major highways.
What type of driveway lasts the longest?
ConcreteConcrete is the old standby for driveways. Most suburban homes opt for this material for two big reasons: Concrete is typically the longest-lasting driveway surface, and, if installed properly, it is practically maintenance-free.
What is the cheapest way to do a driveway?
A gravel driveway is by far the cheapest and quickest to install, especially if the existing driveway's sub-base is sound.
Can you put asphalt over concrete driveway?
If the question is "CAN I lay asphalt over concrete?" then the answer is "Yes." This is absolutely possible if elevations allow for it, and we're happy to lay asphalt driveways over concrete if that's what you want. It's also the cheaper option since heavy equipment is required to dig up an existing concrete slab.
Why is asphalt so expensive?
Unfortunately, thanks to the unstable economy, sulphur fuel regulations, trade restrictions and the promise of more tariffs, construction industry experts predict the cost for raw materials like asphalt and concrete will skyrocket in the coming year.
How much does a ton of asphalt cover?
Asphalt cost per ton One ton of asphalt covers 30 to 80 square feet. A 2-car driveway needs 7.5 to 18 tons of asphalt, depending on the thickness.
How much does it cost to install an asphalt driveway?
Most contractors charge between $12.00 to $17.00 per square foot to install an asphalt driveway. However, there are some factors that could increase the asphalt paving labour cost estimate. For example, if the company has to excavate your driveway first, it could cost you up to $5,100.00 more depending on the size of your driveway.
How much does asphalt cost per square foot?
Asphalt paving costs per square foot range between $2.50 to $4.00 per square foot. The bigger your driveway the more materials will be needed. Uniquely shaped driveways require more work to cover than straightforward parking spaces.
What is the best material for a driveway?
There are two main types of driveway material: asphalt and concrete. Many homeowners choose asphalt not only because the finished product looks nice, but the asphalt paving cost estimate is considerably cheaper than a cement driving pad. Other benefits of installing an asphalt driveway include: Ready to use within a few hours after installation.
How many square feet does a ton of asphalt cover?
One ton covers between 40 to 80 square feet. Average driveway requires 7.5 to 15 tonnes of asphalt. Asphalt paving costs per square foot depend on the cost for manufactures to produce asphalt. For example, when petroleum prices increase, it costs manufacturers more to produce asphalt so the price for consumers also increases.
How thick is asphalt?
Other factors that affect pricing include thickness of the asphalt layer installed. Homeowners can get 5 cm (2 inch) or 10 cm (4 inch) of asphalt on their driveways. The thicker driving path requires more materials which also affect the asphalt paving costs estimate.
Is a driveway a necessary part of the outside of a house?
Your home’s driveway is not only a necessary part of the outside of your home, but a beautifully done parking pad improves your home’s curb appeal. Installing an asphalt driveway is cost effective and, with regular care, will last for years. There are two main types of driveway material: asphalt and concrete. ...
Can you repair a crack in a driveway?
Many issues with the driveway can be easily repaired. This will not only extend the life of your driveway but lower the estimated asphalt paving cost per square foot. Many cracks and small holes can be easily patched or resurfaced, significantly lowering the asphalt paving cost estimate.
What is the best company to repair potholes in Toronto?
Main Infrastructure is the best pothole repair company in Toronto that offers all kinds of asphalt repair and maintenance services. To provide you with a durable and resurrected pavement, we retain the material quality and service standard. View all posts by Main Infrastructure
Is it good to have a rough idea of paving?
Well, there are several attributes of an asphalt paving project affecting your budget. Obviously, having a rough idea before you move forward with your project is good. It gives you an approximate idea of expenses and prevents unnecessary expenses.
Can you reuse asphalt?
Well, go for one ensuring durability to your pavement. Also, you can reuse the previous asphalt of your pavement as the base layer. It will reduce the overall Driveway Paving Cost.
How much does it cost to lay asphalt over concrete?
Laying new asphalt over a concrete driveway costs $1 to $3 per square foot. Contractors fill cracks with concrete-repair caulk before paving. Resurfacing concrete with asphalt is cheaper than replacing concrete. However, special preparation is required to stabilize the concrete and prevent cracks.
How much does stamped asphalt cost?
Colored or stamped asphalt costs $5 to $15 per square foot for a new driveway or replacement, or $3 to $8 per square foot for resurfacing the top layer. A 20x20 stamped asphalt driveway costs $2,400 to $6,000. Decorative patterns are sealcoated, which colors and protects the surface.
How thick should a driveway be?
A new residential driveway needs 3 to 5 inches of asphalt over 4 to 8 inches of rock-base foundation to withstand temperature changes and last 20+ years. Some companies recommend a 2" thickness to save $0.50 to $1 per square foot, but won't provide a warranty due to deterioration risks.
How much does it cost to repave an asphalt driveway?
The average cost to repave an asphalt driveway is $4 to $10 per square foot with a new gravel base or $3 to $7 per square foot with an existing base. Repaving a 2-car (20’x20’) asphalt driveway costs $1,600 to $4,000 on average. Repaving includes removing and hauling away the existing asphalt.
How long does asphalt last?
An asphalt driveway lasts 15 to 30 years and requires sealcoating every 3 to 5 years. Boosts curb appeal and resale value. A new asphalt driveway needs an asphalt layer 3" to 5" thick to last. Resurfacing only the top layer or asphalt overlay costs $1 to $3 per square foot.
How much does it cost to pave a road?
Cost to pave an asphalt road. The average cost to pave a private one-lane asphalt road is $35 to $85 per linear foot. Paving a two-lane (24'-wide) asphalt road costs $70 to $170 per linear foot or $370,000 to $900,000 per mile. Blacktop road construction costs more than driveways because roads need 5" to 11" thick asphalt.
How much does it cost to install asphalt curbs?
Asphalt curbing costs $3 to $6 per linear foot to install. Adding asphalt curbing to a 400-square-foot driveway costs $120 to $240. Repairing or replacing asphalt curbs costs $8 to $15 per linear foot on average. Total costs depend on curb thickness, styles, and labor.
How much does it cost to install asphalt?
Asphalt paving material usually costs $40-80 a ton. One ton will cover 30 to 80 square feet. A residential driveway averages 9-24 square feet. Other materials are needed for asphalt driveway installation as well, and will affect the final cost.
How much does a paver driveway cost?
They offer a wide variety of designs, shapes, sizes, and colors. A paver driveway will cost between $13-15 per square foot. A poured concrete driveway ranges from $7-9 per sq ft.
What is the most expensive option to have a driveway removed?
Repaving. Repaving your driveway requires removing the old driveway completely. This is the most expensive option, because you will be paying to have the old driveway removed and a new driveway installed. This is of course the most expensive option, but a paved driveway has a lifespan.
What is resurfacing a driveway?
Resurfacing is the middle ground of driveway repair. It’s also known as asphalt overlay. In many cases, this can repair significant asphalt cracks. Existing asphalt is covered with a new layer of asphalt, in a process similar to the original driveway.
Why does asphalt crack?
Over time, the heat from the sun’s rays will begin to break down the materials in the asphalt and remove moisture. As the asphalt weakens due to the sun, cracks begin to form.
How long can you drive on a driveway after it's installed?
You won’t be able to drive on our driveway for 3-5 days after it’s installed. You’ll need to avoid parking on the driveway for the first 14 days, particularly in the hot part of the day.
What is the cheapest driveway?
A gravel driveway is the cheapest option if you need a new driveway, at $1-3 per sq ft. It matches with any style of home. Classic gray gravel is well suited to a winding country drive. White gravel provides a modern look.
How long does a concrete driveway last?
Your concrete driveway will last between 50 to 100% longer than its asphalt counterpart.
What is the width of a driveway?
The recommended standard width of a residential driveway construction is between 10 feet and 12 feet. If you have larger vehicles such as a camper, large pickup truck, RV or work van, the proper minimum width is 12 feet.
What is the best material for a driveway?
Gravel or aggregate is one of the most durable and cheapest materials for your driveway construction. It is easy to install and requires no great skill. Nonetheless, it is very durable, only requiring periodic filling and spreading to reduce bumps and rutting once it has settled.
How wide should a double car driveway be?
The recommended width of a double car driveway is between 20 and 24 feet. This will ensure that there is enough space for the drivers to open their doors without touching landscaping features or the other car even if parked side by side.
How much does a home roof installation cost?
The average cost ranges from $2500 and $10,000 depending on the materials used. The higher costs are usually related to the costs of installation including materials and labour and do not necessarily correlate to the long-term durability of the installation.
Is paving stone good for driveways?
Paving stones are beautiful but also one of the most expensive components to use in your driveway construction project. The great thing about paving stones is that they often blend in well with landscape elements such as fountains and walkways. In addition to having high aesthetic appeal, paving stones are highly durable and can last for many years.
Is asphalt a good material for driveways?
Asphalt is a highly functional and top quality material for driveway construction. The good thing about it is that it is cheaper than concrete or paving stones, which are its biggest competitors. The only downside to asphalt is it requires professional installation.
How much does asphalt driveway sealer cost?
Asphalt driveway sealer alone costs between $0.06–$0.11 per square foot on average, while additional modifiers or colors may add another $0.60 per square foot. Coverage rate also depends on the condition and texture of the asphalt. The sealer can also be mixed with sand, which helps add traction back to an asphalt surface.
How much does it cost to seal a 1,000 square foot driveway?
For a larger 1,000 square foot driveway, contractors typically charge between $170 and $240 for sealcoating. Prices depend on whether you get one or two coats and most will charge a minimum fee of $100 to $200 for the project. Blacktop driveway sealer not only helps protect it from natural elements, machine leaks, and other spills, ...
How much does it cost to seal a 20x24 driveway?
The average cost to seal a 20′x24′ two-car driveway is between $100 and $190 depending upon the extent of cracks and holes, the size and layout of your driveway, and the type of sealer used. Contractors typically charge a minimum fee of $100 to $200 regardless of project size and add 50% more to your total cost if two coats are required.
Why was asphalt sealer created?
Created because of the diminishing availability of coal. An asphalt sealer. Quality depends on the type of crude oil used in its manufacturing process and the refinery’s preferred method of blending.
How much does it cost to seal asphalt?
In the United States, the average cost for materials and labor to sealcoat asphalt is $0.17 to $0.24 per square foot. For a basic 480 square foot driveway, you can expect to pay $80 to $115 for sealing. For a larger 1,000 square foot driveway, contractors typically charge between $170 and $240 for sealcoating.
How much does it cost to repair a concrete driveway?
Fixing holes, cracks, and spalling is required before sealing concrete. Concrete driveway repair costs $3 to $8 per square foot on average.
How many square feet is a 2 car driveway?
The average two-car driveway is between 480 and 650 square feet which will help calculate the cost. Depending on the current condition and age of your driveway, you may pay extra for patching holes or other common repairs.
