how much does it cost to install a splash pad

Full Answer

How much does it cost to build a commercial splash pad?

How Much Does It Cost to Build a Commercial Splash Pad? According to experts, depending on the setup you intend to build, the actual cost of installing a commercial splash pad is between $65,000 and $500,000. There are other cheaper options but note that you may end up building and installing the splash pad kit yourself.

Can you rent a splash pad instead of installing?

If you want to save money, you can opt to rent a splash pad instead of having one installed in your home. Check out online sites for areas that offer discounts or promos such as free rentals so that you can save on rental costs. You can also ask some friends around for referrals.

How big should a splash pad be?

A small splash pad is usually 10-20 foot concrete pad with a few spray nozzles. You can keep it simple at that or get fancier by adding size, above ground features and more nozzles. There is also the option to add fiber optic lighting to the water. Increasing the size of the pad gives you more space to add more features.

Why choose a splash pad for your project?

PLANNING AND INSTALLING a properly engineered splash pad will save you time and money in long-term maintenance, operational costs and allow for flexibility when expanding or upgrading your aquatic play solution. Read our 10-Step Guide for planning a Community Splash Pad. Ready to get started on your project?

Do splash pads use a lot of water?

ELLSWORTH — From dawn to dusk, as long as the temperature is above 65 degrees, jets at the Knowlton Park splash pad shoot water high into the air, to the delight of children and adults alike.

How do you install a backyard splash pad?

1:516:04WetDek Backyard Splash Pad Installation (Stand Alone) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSite preparation for a standalone what deck will vary for each installation. But at a minimum willMoreSite preparation for a standalone what deck will vary for each installation. But at a minimum will require some level of excavation. For the wet deck pad. Trenching for the inlet and outlet pipes.

How do you winterize a splash pad?

Clean and empty the water containment reservoir. Empty chemical reservoirs and dispose of chemicals correctly. Remove, clean and properly store chemical probes. Drain and clean sand filter.

What do you need to build a splash pad?

How to Build a Splash PadSplash pad installation kit (including pump, filter, spray heads, drains, holding tank, sanitizer, control boxes)Shovel or backhoe.PVC pipe, fittings, primer, glue.Copper binding wire.UF electrical cable.Level.Tape Measure.PVC saw.More items...

What is the difference between a splash pad and a spray pad?

For starters, while splash pad equipment can include features that spray or pour water on users, there is generally no standing water on the pad to reduce the chance of emergencies. The absence of standing water means that splash pads are more likely to be unsupervised versus a spray park.

How do you keep a splash pad clean?

Clean splashpad of dirt and other debris. To keep your splashpad in good condition, it is important to clear this debris. Give the splashpad a thorough cleaning and make sure drains, pump strainer baskets, and filters are clear to prevent mold or bacteria from growing and water from not draining properly.

Do splash pads use chlorine?

Splash Pads and Germs Explained In other splash pads, the water is recirculated, meaning the pipes drain sprayed water into a tank that is typically underground. Then the water goes through a filter and is disinfected with germ-killing chemicals (chlorine or bromine) before it is sprayed again.

How do you prime a splash pad pump?

0:153:02Pool Pump not working Part 2, Manually prime your pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm going to go ahead and stick it in the skimmer and push it down as far as it'll go in there. AndMoreI'm going to go ahead and stick it in the skimmer and push it down as far as it'll go in there. And then I'm going to turn the hose. Okay.

Can I make a splash pad at home?

This beautiful splash pad is made from a tarp, pool noodles, and a sewing machine. This requires a few sewing skills but if you don't want to sew, it's fine. Use the pool noodles to build the edges of the water area so your kids won't fall out of the splash pad and it is soft, it won't harm your kids.

How do you dry a splash pad?

Turn off the blower, deflate the water slide, and roll it up. Take out the slide on the next day and hose or wash it off. Dry puddles with towels and wipe the Velcro areas. Water drops will air-dry.

How do you winterize an outdoor bathroom?

2:433:38Winterizing Toilets - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just Pat it on the sides. And all that's gonna do this is if you know it's impossible forMoreAnd just Pat it on the sides. And all that's gonna do this is if you know it's impossible for anything to evaporate. If if it can't get to the air so that will that will hold you the whole winter.

How do I winterize my outdoor shower?

How To Winterize An Outdoor ShowerTurn the Water Off. ... Turn the Water On (Drain the Shower) ... Keep the Faucet Handles to the 'On' Position. ... Remove the Shower Head. ... Safely Store the Shower Head. ... Remove the Valve Cartridge. ... Dry Out the Shower Area. ... Close Off the Shower Area.

How do you winterize a building?

7 Ways to Winterize a BuildingAn unpleasant fact of life is that a lot of the energy in your structure or commercial structure spent on heating is wasted due to failing insulation and lack thereof. ... Use weather strips. ... Use draft blockers. ... Install Storm windows. ... Install Heat reflectors. ... Using reflective window film.More items...•

How much does it cost to run a splash pad?

The average cost per month to run a splash pad system for about 6-8 hours a day ranges between $20-$40 per month, depending on electric rates in your area. With our custom control box, you can set a timer for how long you want the water to run in increments (15 or 30 min), and simply restarting it by waving your hand or foot, in front of the motion sensor to easily reactivate the water.

How much does a splash pad cost?

Now you’re asking… will this cost me a fortune and will it affect my electric and water bill? The splash pad cost ranges from $65,000- $500,000 for a commercial grade, and the splash pad cost for a residence is around $15,000-$35,000 depending on what’s best for you. There are some other options that can be cheaper but you’ll end up building a splash pad kit and install it yourself. There is an initial cost when filling the tank and depending on what water filtration system you choose, will affect the amount of water that is used.

How big is a splash pad?

A small splash pad is usually 10-20 foot concrete pad with a few spray nozzles. You can keep it simple at that or get fancier by adding size, above ground features and more nozzles. There is also the option to add fiber optic lighting to the water. Increasing the size of the pad gives you more space to add more features. With more features means more water & with more water means more SMILES! Your splash pad cost will be something you won’t regret!

Where is water held in a splash pad?

The flow through, or fresh water system, water is held in an underground tank, sprayed onto the splash pad and then drains out as waste water.

How much does it cost to install a splash pad?

Depending on the setup that you want, the costs to install a residential splash pad can vary anywhere from $4,000 to as much as $35,000. However, most residential splash pads can cost around $6,000 to $12,000. The costs depend on the size, surfaces, options, and other provisions such as electric work and excavation.

How much does a splash pad cost?

According to SplashPadLLC.com, most residential splash pads can range anywhere from $8,000 to $20,000, while a small commercial splash pad can cost around $30,000.

What are the extra costs?

The average costs, if you were to run it six hours per day, would be about an extra $30 per month in electricity.

What is a ground nozzle splash pad?

Ground nozzles, on most splash pads, will spray either freshwater or treated water upwards out of the rain deck. The nozzles are controlled by sensors or can be run on timers. Some splash pads have moveable nozzles and may also include different types of showers and other features. “ Solo Gibbs Splash Pad ” ( CC BY 2.0 ) by BCRP.

Why are splash pads used in playgrounds?

Splash pads are basically playgrounds that incorporate water to create a fun and wet atmosphere, making water play safer since there is less of a risk for accidents like drowning.

How big is a splash pad?

There are play pads which are generally bigger than landscape pads. Residential splash pads are around 150 square feet.

Why are there separate splash pads?

At some splash pads, there are separate areas for toddlers so that they are safe from the bigger kids running around.

Why is it important to have a splash pad?

PLANNING AND INSTALLING a properly engineered splash pad will save you time and money in long-term maintenance, operational costs and allow for flexibility when expanding or upgrading your aquatic play solution.

How is an aquatic project contracted?

In some cases, the equipment and services needed for an aquatic project will be contracted through a competitive bidding process, whereby a request for proposal (RFP) is extended to potential suppliers and aquatics manufacturers. Through this procurement process, the contract is awarded to the most preferable proposal.

Is aquatic play a success?

Your aquatic play project is a great success and will be enjoyed for years and years to come!

How much did the Hamtramck Recreation Department spend to build a splash pad?

Last fall, the Hamtramck Recreation Department spent $115,853 to build a 900 square foot pad.

Does Hamtramck's cost increase?

Hamtramck’s cost may increase if the DEQ requires modifications.

How much does it cost to run a spray park?

The cost to operate a flow through spray park is between $5,000 to $30,000 per year in water costs, depending on the flow rate and overall size of the park. A recirculating spray park has a range of $5000 to $10,000 and has a much lower yearly cost to operate as it reuses the water. We can do an operating costs estimate that will factor in things like size of your spray park and cost of your utilities.

How much water does a spray park use?

Many flow though spray park are designed for a flow rate of about 70 to 150 gallons per minute (GPM) when operating. The largest flow through spray parks can use up to 250 GPM however this is rare. This flow only happens when the spray park is activated by someone touching the activator and setting off a 3 minutes sequence before it needs to be reactivated. A recirculating spray park only uses water to initially fill the holding tank (typically a 1500 to 3000 gallon underground tank) and then water to make up for losses due to evaporation and bather carry off. We recommend installing a 1 ½” water service to supply a recirculating spray park.

How does a spray park work?

The park will start and go through a set spray sequence and then shut down again until the activator is pressed again. For a recirculating spray park the water treatment system operates continuously 24/7 during the season but the computer system will only allow water to be supplied to the features during the operating hours that have been chosen by the operating staff.

How to commission a flow through spray park?

Commissioning a flow through spray park in spring requires removing the winterizing nozzle covers on the spray park features that are flush with the concrete and installing the spray nozzles. Then the water system will need to be turned on, this usually requires reinstalling the water meter that was removed for winter, closing the drain valves located on each of the feature water supply lines, and checking to make sure each feature solenoid valve operates properly. This typically takes an experienced person ½ day. Commissioning a recirculating system is a bit more involved and requires everything that is done for a flow through spray park plus starting up the water treatment equipment. An experienced person typically completed this in 1 day.

What is a recirculating spray park?

A recirculating spray park requires a connection to the sanitary system to direct backwash water and drain the system.

How to winterize spray park?

To winterize a flow through spray park the water supply is shut off and drained back to a self- draining shut off valve that is below the frost line and the water meter is removed. Then the drains on each of the feature lines are opened to drain any water out of the feature lines.

When do spray parks open?

Many spray parks open at the end of May or early in June and run until the Labour Day weekend. Some operate until the end of September.

Splash Pad Details

• Splash pads can be integrated into any location of your choosing, from a small backyard to an expansive area in the park. Residential play areas are around 150 square feet and include sprayers for kids’ delight. Splash pads are a great way to make your backyard an aquatic playground for ki…

See more on thepricer.org

Any Additional Expenses to Consider?

Is There Any Way to Spend Less?