Hot tub pump replacement cost falls between $200 and $1,200. There are two types of pumps—circulation and two-speed. Circulation pumps cost between $200 and $500 (not including installation) and two-speed pumps cost from $750 to $1,200 to replace.
Full Answer
How much does it cost to replace hot tub pump?
between $200 and $1,200Hot Tub Pump Replacement Replacing a hot tub motor and pump costs between $200 and $1,200, depending on the type. Circulation models run $200 to $500, not including installation. A hot tub pump costs $750 to $1,200 to replace (two-speed pump).
How long should a hot tub pump last?
7-10 yearsMost hot tub pumps and heaters will be able to last for a minimum of 7-10 years in well-maintained, well-balanced water. In poorly balanced water, however, their lifespan can be drastically reduced as key components break down. In hot tub pumps this is commonly the seal that protects the motor from water.
How do I know if my hot tub pump is bad?
Symptoms of Spa Pump Failure There are several signs of hot tub pump failure: Humming noise from motor not turning, frozen shaft, bearings or impeller, or defective starting capacitor. Whining noise from worn bearings. Leaks under the pump from a failure of the pump seals.
What kind of pump do I need for a hot tub?
Hot tubs and spas use high-volume pumps. In a high-volume pump, a large volume of water flows at low pressure. This kind of pump is rated in GPM (gallons per minute). Some people get high volume pumps confused with high pressure pumps which are rated in PSI (pounds per square inch).
Do I have to drain hot tub to replace pump?
You can drain the spa to make the repair, if you need to drain anyway, but it's not necessary. The hoses can be plugged using wine corks or stoppers, or pinched using large needle nose locking pliers (Vice-Grip type). Or you can do a quick swap, described below, and spill a few gallons.
Is it worth fixing an old hot tub?
A hot tub is still worth fixing unless the shell or frame is cracked. Replacing a heater element, control pack, pump or blower is relatively easy and significantly less expensive than buying a new hot tub.
How do I reset my hot tub pump?
1:112:01Go over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs thatMoreGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs that have two breakers. And some hot tubs that have one breaker.
Why is my hot tub pump not working?
Check that your power is on, the breaker or GFCI test button are not tripped, all valves are in the open position. Follow the circ pump plumbing, and look for any kinks in the hose. Pull out the cartridge filter to see if flow improves and the circulation pump is doing better.
Should my hot tub pump run all the time?
The answer to this is… yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they'll need to be drained regularly but for the most part, they are left on 24/7.
How many pumps does a hot tub need?
Most Jacuzzi® Hot Tubs have two separate pumps, for circulation and jet power, and select models even have up to three jet pumps! These power the jets by pulling water through a filter and then pushing it out the jets in our signature 50/50 air-to-water ratio.
What is the difference between a pool pump and a spa pump?
3:567:24So the main difference here is that this pump is able to suck. Air so it can actually draw the waterMoreSo the main difference here is that this pump is able to suck. Air so it can actually draw the water from your hot tub or your pool. Up into the pump. And then it can put it back through the jets.
What does the pump do in a hot tub?
When it comes to hot tub systems, no piece of equipment works harder or is depended on more than your pump. Pumps are responsible for water circulation throughout your tub and the entire system. Pumps draw water from the hot tub and pushes it through the heater and filter and back out through the jets.
Should I leave hot tub pump run all the time?
The answer to this is… yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they'll need to be drained regularly but for the most part, they are left on 24/7.
How long should a spa pump run per day?
Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.
How do I know if my hot tub circulation pump is working?
One of the best things about a hot tub circulation pump is quiet operation; they make almost no noise. Gurgling, humming or grinding noises on a spa circulation pump are good indicators of a problem.
Should I leave my hot tub running all the time?
Yes, you should leave your hot tub on all of the time. Hot tubs are designed to always be switched on and it's more economical to keep the water hot than it is to heat it up from cold each time you want to use it.
How much does a two speed pump cost?
On low speed these pumps use as little as 150-170 watts and cost only $5-6 per month.
What is the phone number for GN hot tubs?
Hot Tub and Spa Pumps know what you are buying - GN Hot Tubs. Give Us a Call: (763) 566-3623 (Central) (763) 566-3623.
How many HP does a jet pump need?
In general, large jets (15-20 GPM) require 1/4 Hp per jet. Some jets are so small you can have a 1 Hp pump drive eight to ten of them. At the other extreme, some small swim spa jets require 1 Hp per jet.
Why do manufacturers use two or more pumps?
Manufacturers often use two or more pumps to power individual groups of jets if the total jet area is extremely large. This practice generally saves money for everybody. We match pumps to the size and number of jets they are expected to run.
Do hot tubs have a pump?
Today most hot tubs and spas use two-speed pumps; the same pump circulates water and powers the jets.
Can you use a big pump in a spa?
Our Advice: Don't specify a big pump for your spa just because it's bigger. If you want more vigorous hydrotherapy action, ask for large volume jets and an appropriately sized pump. If you're still in doubt, call us.
Is a spa pump energy efficient?
Although it's difficult for the consumer to tell the difference, there are high and low energy efficient pumps. Unfortunately for the spa industry, pump manufacturers have moved to inexpensive, inefficient pumps. The result is a higher operational cost for consumers.
How much does a hot tub pump cost?
Hot tub pumps range in horsepower (hp), from 1 hp ( $200) to 5 hp ( $400 to $500 ). If you’d like more water pressure to really work out those knots in your shoulders—or because you can handle the pressure—ask your technician if you can go up. Just be warned: There’s a big difference between 1 and 5 hp.
How much does it cost to get a hot tub pump working again?
The cost of getting your hot tub pump working again depends on what the problem is and where the pump is located. Expect to spend $200 to $1,000 for labor in addition to the cost of replacement parts.
How Much Does It Cost to Repair a Hot Tub Pump Yourself?
A new hot tub pump costs between $200 and $1,200. Hot tub work can be complex, so you might want to save the hassle and guesswork and have a pro diagnose the problem and fix it.
What factors affect the cost of a hot tub pump?
Factors in the cost to fix a hot tub pump include what needs replacing and where the pump is located.
How much does it cost to fix a pump?
If the whole pump needs replacing, though, you’ll likely pay closer to $1,200 for a pro to repair.
Can you fix a pump hidden in a wall?
Pumps hidden in walls or floorboards are more difficult to fix
Can a hot tub pump be installed out of sight?
In addition, many pumps are installed out-of-sight. The contractor might have to open up your wall or floor to get a look at the problem. Expect to pay more for labor if the technician has to contort their body around plumbing fixtures and floorboards to reach the pump’s location. If that’s the case, consider these tips for installing a hot tub.
