Use the remote control to adjust your pilot lights in these few steps:
- Turn on the pilot lights. The flames should burn blue and not orange.
- The remote control has an up and down button. Press and hold on to it until the fire goes out.
- Now adjust the flames to your liking by using the same controls. You can choose to lower or raise the flames.
How to adjust pilot light flame on gas fireplace?
How to adjust pilot light flame on gas fireplace 1 Turn the screw on the control panel to adjust the size of the flame. Use a screwdriver. A clockwise turn will make the... 2 If you have a lo-hi button on the fireplace – use it! It is designed to adjust the flame size. More ...
How does a gas control valve affect a pilot light?
Most gas control valves will have a screw that will adjust the flow of gas to the pilot light assembly. This can make a dramatic difference to the heat given off by the pilot light assembly.
How do you adjust the pilot light on a pilot light?
How to Adjust a Pilot Light 1 Operation of the Thermocouple. The thermocouple is a heat-sensitive electronic device that generates a small electrical signal when it reaches a certain temperature. 2 Adjusting the Thermocouple. ... 3 Adjusting the Pilot Flame. ... 4 Regulating Air Flow. ...
Why is my pilot light too high on my gas fireplace?
So, if your pilot light flame also tends to be too high, ensure that your fireplace doesn’t have a button to bring the flame up or downward. If there’s no such button, adjust a screw on the fireplace. Turning it clockwise will reduce the fire whilst moving the opposite direction will raise it.
How do you adjust a pilot flame?
0:271:25How To: Adjust the pilot flame - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe pilot flame will become higher. When we turn the screwdriver to the right clockwise. The pilotMoreThe pilot flame will become higher. When we turn the screwdriver to the right clockwise. The pilot flame will become lower.
How Big Should the flame be on a pilot light?
A pilot flame should be blue with a yellow tip and strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and adjusted wrong, it will be loud and cause improper furnace operation.
How high should pilot light be on gas furnace?
about 1/2 inchInspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
Should the flame touch the thermocouple?
The pilot flame should touch the thermocouple at a specific level. If the flame is blue and weak, and barely reaches the thermocouple, it needs to be stronger. If it extends well above the thermocouple, it's too strong.
What happens if pilot light is too high?
The pilot flame won't be able to reach the sensors if the flame is too long. The bright, orange light indicates an error in igniting the system. This kind of light does not produce the required temperature level. There is no enough heat to start up the thermocouple.
Why is my pilot flame yellow?
The most common reason why a pilot light would start to burn yellow is that the air intake valve to the pilot light is clogged with dirt. When this happens, air will be blocked to the flame and it will suffer from incomplete combustion (causing the yellow color).
Can you adjust the flame on a gas furnace?
All you will need to do is to twist the adjustment screw of the flame till the flame goes from one and half inches to two inches, which is about 4 to 5 centimeters high. Look for the adjustment screw on the pilot assembly close to the gas valve if the control valve has this adjustment feature.
How do you fix a weak pilot light?
0:561:39Troubleshooting – Service Code 1 Weak Pilot Signal - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's not uncommon to see oxidation. Or corrosion buildup on the electrode itself we'll want to cleanMoreIt's not uncommon to see oxidation. Or corrosion buildup on the electrode itself we'll want to clean that off at the same time looking at your wire. Making sure there's no kinks or cracks splits.
What color should your furnace flame be?
blueThe burner flames from your natural gas furnace should look blue or almost completely blue. A healthy natural gas furnace flame is characterized by a roaring blue flame with a light blue triangle in its center. There may be a tiny tip of yellow.
What is a pilot light supposed to look like?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don't see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
How far should thermocouple be from pilot?
When working properly in most gas appliances, the pilot flame should hit the upper 1/2 to 3/8 of the thermocouple.
What should a gas fireplace flame look like?
Proper Flame Colour A gas fireplace should burn flames that are blue, perhaps with very small tips in yellow or orange. The flames should be steady and consistent no matter what. Although, there is a small exception.
How high should the flame be on a gas fireplace?
Then, turn the gas on and light the pilot. Turn the burner on and set the flame height to high. Take a reading. This time, you want to see an ideal reading of 3.5 inches or the pressure rating indicated in the manual.
What should a fireplace pilot light look like?
A healthy pilot flame will be much like a blue “blow torch” flame. It will shoot sideways and be directly on your thermocouple and thermopile sensors. An unhealthy yellow pilot flame is more like a “candle”. It will shoot straight up in the air and will not engulf your sensors.
Can you adjust the flame on a gas fireplace?
0:032:47How To Adjust The Height Of The Flame In A Fireplace - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you want the flame higher we'll lower it'll say to increase it or decrease it. Or I'll say highMoreIf you want the flame higher we'll lower it'll say to increase it or decrease it. Or I'll say high and low and you just rotate it around according to what you what you would.
How do you adjust the pilot light on a gas stove?
Follow the pilot tube to the control handle until you see an air chamber, and there is where you'll find the screw. Turn the screw clockwise in small increments to reduce the size of the pilot flame. To increase the flame size, turn it counterclockwise.
What happens if the pilot on a gas heater goes out?
Regulating Air Flow. If the pilot on your gas appliance goes out frequently, there may be a draft in the room. Heater gas controls are frequently at floor level, and air can sweep in under nearby doors and blow out the pilot.
How to fix a faulty thermocouple?
Correcting the first condition is a simple process. Simply shut off the gas, reach under the burner and push or pull the probe to reposition it. If the thermocouple is faulty, remove it by unscrewing it from the burner and pulling it out. Reverse the procedure to install a new one.
How long does it take for a thermocouple to reach critical temperature?
It takes about 20 seconds for the probe to reach this temperature when you light the pilot, so you generally have to hold the valve open manually by pressing a button for this length of time.
Do pilot lights work on gas stoves?
Although they are gradually being replaced by electronic ignition devices, pilot lights still provide the flame that ignites many gas appliances, including water heaters, room heaters and stoves. Pilot lights depend on the electric signal from a thermocouple to stay on, and the thermocouple in turn depends on the heat of ...
How big should the pilot light be on a gas fireplace?
The sensors should be like “wrapped” by the flame The distance between two elements is usually near 1 inch, so this is how big should pilot light be on gas fireplace.
What happens if the pilot flame is too long?
If the pilot flame is too long it will not reach the sensors and they could not ignite the system. Also, the bright orange light does not provide the temperature needed for the thermocouple to work. It probably would not cause any damage to the system, but it may have issues with the ignition.
How does a gas fireplace work?
Gas fireplaces have the system of ignition based on the pilot light stand that provides flame and the thermocouple that sends an electric signal for the gas valve. When the pilot is on, the flame gives the right temperature to the thermocouple sensors and in its turn, the thermocouple gives the signal. These two devices depend on each other’s work.
What to do if your pilot light is too high?
So, if your pilot light flame also tends to be too high, ensure that your fireplace doesn’t have a button to bring the flame up or downward. If there’s no such button, adjust a screw on the fireplace.
What does a blue pilot light mean?
It must also be strong enough to cover about half an inch at the end of the thermocouple tip. An intense blue flame with audible noise means an incorrect setting, leading to incorrect operation of the water heater. How to relight a water heater pilot light.
Why doesn't my pilot light work?
Venting should work properly to provide enough oxygen to the system. Problems with the gas regulator or gas availability. These may be the reasons why the pilot light doesn’t work properly. Try to check each of them by yourself or get professional help for troubleshooting gas fireplace pilot lights.
What does a clockwise turn on a fireplace do?
A clockwise turn will make the flame smaller and the counterclockwise turn will increase it . If you have a lo-hi button on the fireplace – use it! It is designed to adjust the flame size. If it didn’t help you may probably need to clean the pilot assembly or to change it.
