Is it hard to install a new toilet?
Replacing and installing a new toilet isn't as hard as it sounds. All you need are a few hours, a helper and the right tools and toilet parts for the job.
How much does it usually cost to install a new toilet?
On average, the cost to install a toilet ranges between $400 and $800. One-piece toilet labor costs range from $100 to $300. Two-piece toilets cost slightly more to install than one-piece toilets because of the additional labor. A two-piece toilet typically costs $200 to $300 to install.
Is installing a new toilet messy?
As we've alluded to a few times now, replacing an old toilet with a new one can be a very messy job. At the end of it, there is likely going to be a small, contained mess in your bathroom that will need to be cleaned up.
How long should it take to install a new toilet?
The time frame for fitting a toilet varies from one to four hours, depending on your level of DIY experience. Any new toilet installation requires prior preparation and, essentially, working backwards from removing an old toilet.
How much does Home Depot charge to install a toilet?
The Home Depot charges a standard fee of $99 for toilet installation. The charges are inclusive of the cost of the toilet, labor, and materials. However, the total cost will vary depending on the specific model of toilet you choose, as well as any additional features or services you request.
Is replacing a toilet worth it?
The general rule of thumb is that you should replace the toilet if the cost of repairs is more than half the cost of getting a new toilet. Sometimes, the issue is one big problem. Problems like a crack in your toilet bowl can be a major hassle, so they are almost never fixed.
What can go wrong when changing a toilet?
Well, it isn't, and here are five of the most common mistakes that can lead to a disastrous and messy toilet replacement.Forgetting to Drain Water Before Toilet Removal. ... Failing to Measure Your Water Line. ... Letting Your Flange Sit Too Tall. ... Leaving the Tank Lid On During Removal. ... Overtightening Nuts and Bolts.More items...•
How long does it take to remove and fit a new toilet?
Installing a toilet takes between 1 hour and 4 hours depending on the level of experience and type of toilet you're planning to install. Once your toilet installation is complete, you'll want to fit a toilet seat. If you're unsure how to do this then check out our guide to fitting a toilet seat which will help you.
Do I need to caulk around the bottom after installing a new toilet?
Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It's actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?
What do I need to know when replacing a toilet?
0:161:50Things to Consider When Purchasing a New Toilet | The Home DepotYouTubeStart of suggested clipEnd of suggested clipYou'll need rubber gloves a water supply line now you don't have to replace that but it's probablyMoreYou'll need rubber gloves a water supply line now you don't have to replace that but it's probably just as old as the toilet you're replacing.
Should I replace toilet or floor first?
The bathroom fitters are unanimous—if you're looking for a high quality finish, with a better seal against water damage, then always tile the floor first.
How much does it cost to remove and install a toilet?
According to Angi and HomeAdvisor, the cost to replace a toilet ranges from $224 to $532, with a national average of $371.
Is it cheaper to fix a toilet or replace it?
The national average price for repairs is $60 to $200, with most people paying $125 on average to replace a fill valve on a slow-running toilet. This price fluctuates up or down depending on the amount of work and parts involved....Toilet Repair Price.Toilet Repair CostAverage range$60-$200Low-end$50High-end$3,9001 more row•Mar 28, 2022
How often should you replace toilet?
On average, most toilets will have a lifespan of between 10 and 15 years, even with regular use. The lifespan may vary depending on the toilet model and the wear and tear it experiences over the years. Most toilets will start to give you warning signs indicating the time for replacement is near.
How far apart should a toilet be from the wall?
1. Measure the distance from the wall to the floor bolts before removing. Standard toilets have a measurement of 12" from the wall to the floor bolts. If your toilet measures 12", you can expect to buy any standard toilet and install it comfortably in the existing location without much hassle.
What do you do when you flush the toilet?
Flush the toilet to empty the basin and bowl.
What to do if toilet wax seal is cracked?
The wax seal has cracked or broke. All you need to do is remove and reinstall the toilet with a new wax seal.
What does it mean when a toilet ring is leaking?
If it does, that points to a bad seal of the wax ring. Otherwise, one of the drain pipes may not have been glued, allowing water to leak.
How to get rid of water in toilet bowl?
Remove any leftover water in the toilet bowl and toilet basin. You can use a small cup at first, and then switch over to a heavy-duty sponge. Dump the excess water into a bucket and dispose of it somewhere safe. ...
How to keep sewage fumes from wafting into bathroom?
Plug the drain opening with an old rag or another implement. This will keep the sewage fumes from wafting into your bathroom before you install the new toilet.
Where to put wax ring on toilet?
Fit a new wax ring around the bottom of the toilet bowl, just around its drainage hole. Wax rings come either plain or with a funneled inside edge.
How long does it take to install a toilet?
Here, we asked This Old House plumbing and heating expert Richard Trethewey to show how to install a toilet. The time required varies, but give yourself half a day if you’ve got a lot of experience with plumbing jobs, and a full day if you’re a novice.
What to do if your toilet leaks?
If your trusty toilet has developed cracks or leaks, uses far too much water per flush, or is simply a shade of baby blue not seen in 20 years, it may be time to replace it. You might consider this a good time to put in a call to the plumber, but it can be all in a day's work for a reasonably handy DIY-er. It's not for the weak, since toilets are heavy and unwieldy, but if you have a strong back (or a sturdy assistant) you can save yourself the cost of a house call by installing it yourself.
How to tighten a closet bolt?
Tighten the nuts with a wrench one quarter turn at a time, alternating between the two. Stop when the wrench meets firm resistance; overtightening will crack the bowl. With a hacksaw, trim the closet bolts at a point two threads above the top of the nut. Snap the plastic bolt covers into place.
How to tighten a plastic tank supply line?
Hand-tighten the supply line's plastic nut under the tank. Then tighten the compression nut with a wrench.
How to clean a valve inlet?
Dry the pipe inside and out with a rag. Clean the inside and outside of the pipe and the inside of the valve's inlet using a wire-brush pipe cleaner. Apply flux to both areas.
How to lower a tank?
Gently lower the tank onto the back of the bowl, guiding the ends of the tank bolts into the holes.
How to fit a tank supply line?
Using a tubing bender, curve the supply line to fit between the stop-valve outlet and the tank-supply fitting. Then hold the pipe, flared-end-up, between these two points and mark it half an inch below the outlet. This will leave enough line to sit inside the outlet.
How to make a toilet easier to install?
That means you have to cut off the protruding ends later with a hacksaw. But first connect the water line, flush the toilet a couple of times and check for leaks. Leaving the bolts uncut until you’ve done these final checks lets you easily remove and reset the toilet if you find any problems.
How to measure for a new toilet?
from the wall. But with a few models, that measurement is 10 in. or 14 in. To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models. If you have to special-order a toilet, be prepared to spend much more. If there’s a door near the toilet, also measure how far the bowl protrudes from the wall. If you are replacing a toilet with a standard bowl with an “elongated” model, the door may not close. Read on to learn how to install a toilet.
What does a toilet bolt look like?
Some metal toilet bolts have a yellowish zinc coating that makes them look like brass. So check the label and make sure you’re getting brass bolts and nuts. They won’t rust away and they’re easier to cut off later. If you need to reanchor the toilet flange, buy stainless steel screws. They won’t corrode like steel or break off like brass while you’re driving them.
Why does my toilet rock?
If the flange is loose or damaged , the toilet will rock. And a rocking toilet will distort the wax ring and cause leaks. So be sure to scrape off the old wax ring and inspect the flange. Here are some solutions for broken, corroded or loose flanges.
How to fix rot under toilet flange?
The best solution depends on the extent of the rot. If the rot is only under the flange, use an ear-type repair ring. The ears let you drive screws into firm wood farther away from the flange. Before you install this kind of ring, hold it up to the drain horn on the underside of the toilet.
How to check rough in on a toilet?
To check the rough-in, just measure from the wall to the toilet’s hold-down bolts. If that measurement (plus the thickness of the baseboard) isn’t approximately 12 in., toilet shopping will be a bit harder. Most home centers carry only one or two 10-in. models and no 14-in. models.
Can you weld toilet bolts?
Don’t be surprised if the old nuts that hold the toilet in place won’t budge. Years of corrosion can weld them to their bolts. In that case, a hacksaw blade is the solution. You can buy a “close quarters” blade holder at home centers and hardware stores, or just wrap a bare blade with a rag or duct tape. Most toilet bolts and nuts are brass, so they’re easy to cut. If the bolt spins, grab it with locking pliers as you cut.
