Should Shoe Molding Match the Baseboard or the Floor? While there’s no hard and fast rule on this, here’s our thoughts on it: If you are laying quarter round or shoe molding on hardwood floors, you should lay a quarter round or shoe molding that matches the floor wood grain & stain.
Full Answer
Should hardwood floors match the baseboards?
Your hardwood floors and baseboards do not need to match if you will not like the way they look. It might be best to bring some friends over to look at different test samples. This method helps give multiple comparisons so you feel confident in your color or stain choices.
How to finish shoe molding?
Moulding Finishing Guide
- Paint or Stain
- Drop Cloths
- Rags
- Wood Putty, Caulk and Caulk Gun
- Brushes
- 220 Grit Sandpaper
Should your wood floor match your trim?
Should your wood floor match your trim? One of the most common misconceptions that clients have is that you have to match your trim , baseboard and other woodwork to the flooring color. But you can also Paint all the trim in a contrasting color to make the hardwood floors pop.
Which nails should I use for shoe molding installation?
“Traditional” Shoe Molding Installation. Use either your nail gun or your hammer and nails to secure the shoe molding firmly to the wall. Evenly space them apart, they should be no closer than 9 inches to each other. If you’re wondering “Which nails should I use for shoe molding?” the answer is 2″ brad nails for the nail gun. Try to find smaller finishing nails for your hammer so they’re not so noticeable on the shoe molding.
What is shoe molding?
How wide is shoe molding?
How much does shoe molding cost?
Why is shoe molding called shoe molding?
What is the glue used to hold molding in place?
When did shoe molding start?
Does baseboard cover the gap?
See 4 more
About this website
Should shoe molding match trim or floor?
Should Shoe Molding Match the Baseboard or the Floor? While there's no hard and fast rule on this, here's our thoughts on it: If you are laying quarter round or shoe molding on hardwood floors, you should lay a quarter round or shoe molding that matches the floor wood grain & stain.
Should quarter round match baseboard or floor?
They unanimously said quarter round molding should be painted the same color as the baseboard. It should not be stained the same color as the wood floor, as it should look like an extension of the baseboard, not an extension of the floor.
Should floor molding match the floor or wall?
Traditionally it should match the trim.
Should baseboard match hardwood floor or doors and trim?
It is not a requisite for your hardwood floor to match your trims. However, matching your floors with trims can be visually appealing in many cases. Therefore, you will have to understand the visual effects brought about by your painted or stained trims to decide the best option.
Is quarter round or shoe molding better?
Because quarter-round molding is thicker and taller than most shoe moldings, it covers imperfections better than the alternative. So if you're installing molding to hide your home's flaws, quarter-round is the way to go.
Should shoe molding touch the floor?
To ensure a no-gap fit, push down on the base shoe molding using a wood block to keep it against the floor. Using a pneumatic brad nailer, attach the shoe molding to the baseboard. Tip: It is important to remember that shoe molding should always be nailed into the baseboard and never into the floor.
What should baseboards match?
Painting your walls or floor a different color than your baseboard can either make it stand out or create an unwanted visual contrast. But when it comes to identifying the proper color matching for your baseboard to walls or flooring, there is no right or wrong answer.
Should Trim be darker than floor?
It is still possible to maintain consistency and balance by coloring your floor slightly darker or lighter than the trim. Tradition calls for the flooring to be the darkest color in any room, while the ceiling should be the lightest.
How do you deal with shoe molding?
1:405:36How To Cope Molding for Inside Corners - WOOD magazineYouTubeStart of suggested clipEnd of suggested clipCut along the outline. Created by the miter. You want to stay on the waist side of the line you'llMoreCut along the outline. Created by the miter. You want to stay on the waist side of the line you'll be fine tuning the cope after removing the bulk of the lace.
Do you need shoe molding on wood floors?
Using shoe molding gives the floor installer more latitude in their end cuts and also allows you to hide the expansion gaps between the wall and the floor. Due to the small and flexible nature of the shoe molding, it is able to expand and contract along with the floor.
Do door frames and baseboards have to match?
MYTH: Everything should match Similarly, door casings and doors don't have to match. Having a light casing and baseboard contrast a dark door achieves a very modern look. Still, keep in mind that choosing colours that are simple will make it easier to change wall colours in time, if desired.
Do baseboards and trim have to match?
The baseboards do not have to match the trim. As long as the color of the baseboards and the color of the trim complement one another, your room will still look cohesive. If you want to match your baseboards and trim, that is always an option. Below is an example of baseboards and trim that are the same color.
How do you match quarter round?
2:475:18How To Cut Quarter Rounds For A 90 Degree Angle - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd a larger edge this larger edge is the one that goes on the bottom. So literally a corner roundMoreAnd a larger edge this larger edge is the one that goes on the bottom. So literally a corner round is literally going to be sitting exactly. Like.
Why is quarter round used on baseboards?
Quarter round is another moulding style typically paired with baseboards to cover up gaps and imperfections between the base and the floor. As such, it essentially has the same purpose as shoe moulding.
Can you use quarter round without baseboard?
While quarter rounds can jazz up a baseboard, they can also be used in lieu of baseboards. These pieces of wood will still join the gap between the floor and the wall, and they are usually a bit more flexible, allowing for pleasing visuals at a fraction of the cost.
Do you need quarter round with vinyl plank flooring?
No you never need to use quarterround.
Shoe Molding vs. Quarter Round: What’s the Real Difference?
While both pieces of molding are applied to the baseboard, quarter round is 1/4″ round circle and shoe molding is 1/8″ in a round circle. Shoe molding doesn’t come out as far from the wall.
5 Types Of Shoe Molding (With Photos) – Upgraded Home
Unlike similar materials such as polystyrene, you are unlikely to bend and damage PVC shoe molding. PVC can withstand knocks, tears, and foot traffic that would otherwise be harmful to other materials.
8 Base shoe ideas | moldings and trim, baseboard styles, baseboards
Feb 8, 2019 - Explore A Bentz's board "Base shoe" on Pinterest. See more ideas about moldings and trim, baseboard styles, baseboards.
Which nails should I use for shoe molding installation?
I'm about to install shoe molding all over my house. The baseboards are hung for carpet, but we're replacing the carpet with vinyl. So I have a pretty good sized gap to cover. I'll probably use 11/16
How much does shoe molding cost?
Wood is the most common type of shoe molding, and you can buy inexpensive (paintable) pine shoe molding for $5 to $6 per eight-foot section. Hardwood shoe molding, including oak, ash, and walnut, which can be stained to match your trim, runs $6 to $10 per eight-foot section. Medium-density fiberboard (MDF) shoe molding is made from a combination ...
What is quarter round trim?
If you’ve been looking at baseboard finishing trim, you’ve probably discovered quarter-round, too. As the name implies, this type of molding is one-quarter of a round dowel (split a dowel down the middle, then further split the halves, and you’ll have quarter-round). While quarter-round can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding , which is taller and narrower than its curved counterpart.
What is mitering corners?
Mitering corners means to cut the ends of the two pieces of baseboard at 45-degree angles that meet to form a corner. Before nailing the molding in place, put a small dab of construction glue on each end. While the nails hold the molding in place, the glue acts as extra insurance to keep the corners snug.
What is shoe molding?
Paired with baseboard and stained or painted to match your trim, shoe molding (also known as “base shoe”) is a small, thin strip of molding that gives your room a finished look. Shoe molding adds a decorative touch while covering any gaps that might lie between the bottom of baseboard and the floor. Not all types of baseboard are suitable ...
Why is shoe molding called shoe molding?
Shoe molding, so called because it’s located at “shoe level,” caught on because it looked good and also helped seal out insects and dirt. Today, the main goal of both baseboard and shoe molding is to conceal the less-than-appealing transition between the bottom of the wall and the floor. Baseboard alone covers most of the gap, ...
How much does polystyrene cost?
Polystyrene shoe molding is the least expensive option, running $2 to $3 per eight-foot section, and it’s meant to be painted. Polystyrene is not as durable, however, as either MDF or wood, and it tends to dent if bumped. Photo: istockphoto.com.
What is the glue used to hold molding in place?
While the nails hold the molding in place, the glue acts as extra insurance to keep the corners snug. Cope inside corner joints. Most corners in a room will be inside corners, and while you might be tempted to create another miter joint for them, mitered joints in inside corners tend to gap.
What to do with molding to match hardwood floor?
Stain the molding to match the hardwood floor
Why is the shoe mold painted?
The reason for this is the shoe mold is actually considered to be part of the “base” trim assembly.
What is the most common trim color?
The most common trim color is white, and so this most often will lead to a white quarter round trim. One exception to this rule is when a ceramic or vinyl floor sits next to a room with hardwood and the quarter round continues from a hardwood area to a tiled area.
What color should I paint a kitchen with walnut floors?
If your kitchen has walnut floors I would paint the quarter-round white to match the baseboard rather than highlight one stain over the other.
What is a quarter round?
Painted quarter round is a PIA, it shows dust, dirt knicks and knocks. If you have laminate or wood floor it’s hard to paint it without getting some on the floor. Wood stained quarter round doesn’t show dirt or dust as ez. If you ding it, a little touch up stain on a paper towel does it.
What color is pine baseboard?
Bought pine and painted it the color of the baseboard which is a very pale yellow.
Is staining cheap pine wood uniform?
6. Hardwoods have different colors with each piece due to the grain and cut of wood, so if you merely stain cheap PINE wood, each length is uniform in color, and while you might get CLOSE to matching, it screams CHEAP more than a finely painted piece of shoe molding 🙂
What was the rough shape of the hardwood floors?
The hardwood floors were actually in pretty rough shape. Not structurally, mind you. The tops were rough from 40 years of having one carpet on them. They were a product of the old way of installing carpet. Imagine a 1 inch thick pad of dense sponge that is charcoal colored. Now imagine it sticks like clue to everything. That is what used to be under older carpets. The stuff is nearly impossible to get off in one pass.
What is a quarter round?
Quarter round comes in many lengths and resembled a very long cylindrical wood dowel that has had three quarters of it removed , from end to end. Hence the name, quarter round. A quarter of it is all that is left. So, instead of ripping out all that pristine baseboard and replacing it with much, much thicker stock, I just tacked in quarter round throughout the house.
How many different stains can you get for each hardwood floor?
Get 3 different stains, one for each hardwood floor type.
What is a swatch?
Swatches are little pieces of plastic that have a color printed on them and a name so you know what it is called. You place them on the floor and flip through them until you find your closest match. Then you take that back to the hardware store to get the stain you desire.
Do hardwood floors and baseboards need to match?
Do my hardwood floors and baseboards need to match? Your hardwood floors and baseboards do not need to match if you will not like the way they look. It might be best to bring some friends over to look at different test samples. This method helps give multiple comparisons so you feel confident in your color or stain choices.
Is refinishing hardwood floors expensive?
Refinishing hardwood floors and installing baseboards can be a time consuming, and expensive project. One that will leave your body sore and the kind you really only want to have to do from scratch one time.
Is baseboard cheap?
This actually created a pretty substantial cost savings in the end. Baseboard is not cheap. Once you include an uncommon thickness your price will get out of control quickly. In the end, I was given some stain “swatches” from the hardware store to take home and I matched it all.
What is shoe molding?
Paired with baseboard and stained or painted to match your trim, shoe molding (also known as “base shoe”) is a small, thin strip of molding that gives your room a finished look. Shoe molding adds a decorative touch while covering any gaps that might lie between the bottom of baseboard and the floor. Not all types of baseboard are suitable ...
How wide is shoe molding?
Standard shoe molding, available at home improvement centers and lumberyards, comes in widths of 7/16-inch to ½-inch and ranges from ¾-inch to 1-inch in height. It’s also made in a variety of material options to match the different types of baseboard.
How much does shoe molding cost?
Wood is the most common type of shoe molding, and you can buy inexpensive (paintable) pine shoe molding for $5 to $6 per eight-foot section. Hardwood shoe molding, including oak, ash, and walnut, which can be stained to match your trim, runs $6 to $10 per eight-foot section. Medium-density fiberboard (MDF) shoe molding is made from a combination ...
Why is shoe molding called shoe molding?
Shoe molding, so called because it’s located at “shoe level,” caught on because it looked good and also helped seal out insects and dirt. Today, the main goal of both baseboard and shoe molding is to conceal the less-than-appealing transition between the bottom of the wall and the floor. Baseboard alone covers most of the gap, ...
What is the glue used to hold molding in place?
While the nails hold the molding in place, the glue acts as extra insurance to keep the corners snug. Cope inside corner joints. Most corners in a room will be inside corners, and while you might be tempted to create another miter joint for them, mitered joints in inside corners tend to gap.
When did shoe molding start?
Tall baseboards were popular during the Greek Revival period in the early-to-mid 1800s, but the idea of adding shoe molding to baseboards began in Europe and the United States during the Victorian era of the late 1800s.
Does baseboard cover the gap?
Baseboard alone covers most of the gap, but because it’s larger than shoe molding, it’s relatively stiff and doesn’t conform well to an uneven floor. Even after baseboard has been installed, you will often see small gaps here and there between the baseboard and the floor. That’s where shoe molding comes in.