What are OSHA Planks
- 1.Glued laminated Lumber (Glulam) The glulam are pine boards with measurements 2×6 that are glued together to come up with a beam measuring around 6×10. Thereafter, three scaffold planks with measurements 2×10 are created from the beam.
- 2. Pinned Planks ...
- 3. Laminated Veneer Lumber
What are OSHA grade planks made of?
OSHA Grade Planks are made of Yellow Southern Pine, Clipped, Rodded and OSHA Stamped. Come in three sizes: 8', 12' and 16' lengths. All planks are 2" high by 10" wide and rod and clipped. If you have any questions on OSHA Planks, you can contact one of are Sales Reps @ 800-776-3595.
What are your scaffold planks made of?
Our scaffold planks are made from No. 1 DI65 pine and are tested by an independent agency to make sure they meet or exceed OSHA’s deflection standards under medium duty (50 lbs./sq. ft.) conditions. What Length Should Your Scaffold Planks Be? 16′ boards will cover two 7′ spans. Use these boards whenever a long work platform is needed.
Do Your scaffold planks meet OSHA’s requirements?
OSHA has strict requirementson how much the boards can deflect under a load. We have taken the guesswork out for you. Our scaffold planks are made from No. 1 DI65 pine and are tested by an independent agency to make sure they meet or exceed OSHA’s deflection standards under medium duty (50 lbs./sq. ft.) conditions.
What are OSHA grade scaffold boards made of?
OSHA Grade - Wood Scaffold Planks. •Bird Ladder & Equipment Co. is a nationwide distributor of premium quality DI65 Solid Sawn Southern Yellow Pine Scaffold Plank. •OSHA Grade Planks are made of Yellow Southern Pine, Clipped, Rodded and OSHA Stamped. •Come in three sizes: 8', 12' and 16' lengths.
What is OSHA plank?
What is the first quality of OSHA planks?
What is glulam lumber?
What is a pinned plank?
Why do planks need to be tested?
Why do manufacturers test and emboss planks?
Is a plank cost effective?
See 2 more
What wood is used for scaffold planks?
Wood, such as fir or pine, is the most common material. High-quality wooden planks, such as Kennison Forest Products solid sawn scaffold planks or sure-lam LVL (laminated veneer lumber) scaffold planks, provide durable, safe planking solutions.
Can you cut OSHA planks?
Cutting them to length is not a problem since there is no special treatment of the end of these planks. Do use reasonable care in cutting and handling the planks to avoid having any separation of the lamination.
What material is acceptable for scaffold planks?
(b) Solid sawn wood used as scaffold planks shall be selected for such use following the grading rules established by a recognized lumber grading association or by an independent lumber grading inspection agency. Such planks shall be identified by the grade stamp of such association or agency.
What is an OSHA board?
Occupational Safety & Health Standards Board (OSHSB) The mission of the Occupational Safety & Health Standards Board is to promote, adopt, and maintain reasonable and enforceable standards that will ensure a safe and healthful workplace for California workers.
How much does a OSHA plank weigh?
Weight: 40.0 lbs. Edges are "Clipped" to reduce end-shearing and ease of handling. Ends are "Pinned", or "Rodded" to reduce end cupping or splitting. Ends are sealed to prevent moisture and chemical entry.
How much weight can an OSHA plank hold?
OSHARated load capacityIntended loadMedium-duty50 pounds per square foot applied uniformly over the entire span area.Heavy-duty75 pounds per square foot applied uniformly over the entire span area.One-person250 pounds placed at the center of the span (total 250 pounds).3 more rows
Are scaffold boards hardwood or softwood?
softwoodScaffolding wood is a safe material to keep in homes. Although it is softwood, scaffolding wood comes in thick planks that make sturdy furniture. If it is not treated with glues, finishes and paints, scaffolding wood can be recycled into engineered wood products or fuel.
How thick the scaffold plank timber should be?
The standard size for a new scaffold board is a thickness of 38mm, a width of 225mm, and lengths going up to 3.9m (13ft). As timber goes, scaffold boards are fairly "chunky", which is what gives them a wonderfully rustic and industrial aesthetic and feel.
Can scaffold boards be used as flooring?
A cheaper option for flooring are used scaffold boards, at a fraction of the cost of reclaimed floorboards you get a lot more coverage for your money. With a bit of DIY knowledge, time and money and elbow grease the results are great.
How much does a 16 OSHA plank weight?
Weight: 64.0 lbs.
What size is an OSHA plank?
OSHA Grade Planks are made of Yellow Southern Pine, Clipped, Rodded and OSHA Stamped. Come in three sizes: 8', 12' and 16' lengths. All planks are 2" high by 10" wide and rod and clipped.
What is scaffold grade lumber?
Scaffold-grade lumber is meant to withstand forces not imposed on ordinary, construction-grade wood (which is only two-thirds the capacity of scaffold-grade). Using construction-grade lumber on a scaffold platform not only violates OSHA standards, but is also an unsafe practice and an invitation to a deadly incident.
Can you cut scaffold boards?
Cut the scaffold boards to the length you've chosen. If you don't want to use the metal ends, you can cut off the end of the planks beyond the metal trim (don't try to saw through the metal) before measuring and cutting the length.
Should scaffold boards be clipped down?
TG20 recommends boards which are nominally 38mm thick and less than 2.13m long, should not be used unless they are fixed down to prevent tipping. Boards which are less than 1.6m long may be supported on two transoms but should be fixed down at both ends.
How do you cut a plank?
0:190:55How to Measure and Cut Plank and Mill Wood Wall Planks - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a jigsaw make sure your piece is supported. Then cut along the mark using a square as a guideMoreUsing a jigsaw make sure your piece is supported. Then cut along the mark using a square as a guide or for the most professional.
Does scaffold planking need to be approved by OSHA?
OSHA does not require that scaffold planks be graded and stamped by a qualified grading agency. However, employers must ensure that scaffolds are designed, erected, used and maintained in compliance with the provisions of Part 1926 Subpart L? Scaffolds.
Requirements for scaffold plank. | Occupational Safety and Health ...
October 3, 1985. Mr. John Rectenwald General Electric Corporation 1100 West Avenue, Building 16464 Lynn, Massachusetts 01910. Dear Mr. Rectenwald: Mr. Richard B. Starrak, President George McQueston Company, Inc., located in Iron Horse Park, North Billerica, Massachusetts, requested that this office write to you concerning the Occupational Safety and Health Administration's (OSHA) requirements ...
Compliance of Master Plank scaffold planking with OSHA plank strength ...
You have submitted tables showing the maximum loads for specified spans of various widths of your scaffold plank products. These are for medium-duty, heavy-duty, one-person, two-person and three-person.
DI-65 OSHA Scaffold Planks Tough and Safe ⋆ OSHA ScaffPlank
Schedule your delivery 203-376-0036 OSHA ANSI A10.8 standards 16’, 10’, and 8’ OSHA-SCAFFPLANK MSR 2400/DSS
Wood Scaffold Planks | OSHA Boards - Southwest Scaffolding & Supply, LLC
Our Scaffold boards are made from high-quality No. 1 DI65 pine. They are inspected by an independent agency to make sure they meet or exceed OSHA’s board and deflection standards under medium duty (50 lbs./sq. ft.) conditions.
Laminated Scaffold Planks-OSHA&AS1576 LVL Board - Wellmade
Timber Laminated Scaffold Planks. Wellmade laminated scaffold planks are certified by OSHA and AS1577 standards. It is manufactured from high-quality New Zealand pine lumbers.
What happens if you fail to fix planks?
Whenever you fail to follow these guidelines when fixing or operating on the planks, serious disaster may befall the workers or the building under construction. At the end of the day, this will lead to extra expenses in hospital bills and even worse, lawsuits.
How wide should a platform be?
Each walkway and platform should not be less than 46cm wide.
How much weight should a scaffold support?
Scaffold components should support their own weight as well as that of a load weighing around 4 times their weight. Each suspension rope used on suspension scaffolds that are non-adjustable should be able to support 6 times the intended weight applied to the rope.
How far should the front edge of a platform be from the work face?
The front edges of the platforms should not exceed 36cm from the work face. If this is the case then the platforms must have guardrail systems.
How wide should scaffolding be?
Where scaffolds are very narrow that the walkways and platforms cannot be more than 46cm wide, fall arrest systems and or guardrails shall be used for protecting the employees from hazards like falling off the platform. The front edges of the platforms should not exceed 36cm from the work face.
What is scaffolding planking?
The planking portion of OSHA's Scaffolding eTool is intended to address the need for specific and accurate information about arguably the single most critical scaffolding component: The lumber from which platforms are made.
What is the span of a scaffold plank?
The span of a scaffold plank is the distance it runs between supports. The longer the span, the more deflection (bend) it will have, and therefore, the less its load-bearing capacity will be. For 2 x 10 (nominal) or 2 x 9 (rough) solid sawn wood planks, allowable spans for a given load are shown in the table below:
How much deflection can a scaffold have?
To assure that scaffold planking remains within its safe load-bearing capacity, it may not be allowed to deflect more than 1 / 60 th of its span between supports. [ 29 CFR 1926.451 (f) (16)] The table below shows how little deflection that is.
How many inches to the side of a Douglas Fir board?
The slope of the grain (1 inch to the side for every 16 inches along the length of the board for Douglas Fir, 1/14 for Southern Pine).
Is scaffold grade lumber unsafe?
Using construction-grade lumber on a scaffold platform not only violates OSHA standards, but is also an unsafe practice and an invitation to a deadly incident.
Can scaffold planks be left in service?
Scaffold planks that have accumulated layers of paint, plaster, etc. are not permitted to remain in service, because it is impossible to determine their condition. Dangerous splits may be hidden underneath these coatings. [ 29 CFR 1926.451 (b) (9)]
Can a scaffold plank be used as a mudsill?
If a scaffold plank has been used as a mudsill, it should not be returned to service on a platform. Moisture from standing water, as well as point-loading from the scaffold legs, may have weakened it, making it unable to bear the weight that will be placed on it.
What is a scaffold plank made of?
Our scaffold planks are made from No. 1 DI65 pine and are tested by an independent agency to make sure they meet or exceed OSHA’s deflection standards under medium duty (50 lbs./sq. ft.) conditions.
What Length Should Your Scaffold Planks Be?
16′ boards will cover two 7′ spans. Use these boards whenever a long work platform is needed. The extra length ensures these boards stay in place better and allow you to construct the work platform faster.
What size is a 65 plank?
Dense Industrial 65 Scaffold Plank Proper use of 1 -1/2″ x 9 – 1/4″ (S4S) smooth surface scaffold plank under dry use (<19% moisture) that meets the grading rules published by the grading agencies approved by the American Lumber Standards Committee and ANSI safety requirements.
Is compression wood prohibited?
Compression wood – Prohibited if in readily identifiable and damaging form.
What is multi employer OSHA?
Under that policy, a "controlling employer" has safety and health obligations with respect to a subcontractor's employees in certain circumstances. We defined a controlling employer as one "who has general supervisory authority over the work-site, including the power to correct safety and health violations itself or require others to correct them." If the general contractor has this kind of authority, then it would be considered a controlling employer. The act of hiring a grading specialist would not, by itself, make an employer a controlling employer. It may, however, be indicative of general supervisory authority or the ability to detect and correct safety problems at the site.
What is Appendix A to Subpart L?
Appendix A to Subpart L is a non-mandatory guide that may be used to help select lumber for scaffold planks. Under this appendix, when calculating lumber strength for purposes of complying with Subpart L, the qualified person may base his/her calculations using the grading rules established by a recognized lumber grading association, or an independent lumber grading inspection agency, and certified by the Board of Review, American Lumber Standard Committee, as set forth in the American Softwood Lumber Standard (ASLS) of the U.S. Department of Commerce. For your convenience, the current list of certified agencies is enclosed.
What is OSHA interpretation letter?
OSHA requirements are set by statute, standards and regulations. Our interpretation letters explain these requirements and how they apply to particular circumstances, but they cannot create additional employer obligations. This letter constitutes OSHA's interpretation of the requirements discussed. Note that our enforcement guidance may be affected by changes to OSHA rules. Also, from time to time we update our guidance in response to new information. To keep apprised of such developments, you can consult OSHA's website at https://www.osha.gov.
Does OSHA require scaffold planks to be graded?
OSHA does not require that scaffold planks be graded and stamped by a qualified grading agency. However, employers must ensure that scaffolds are designed, erected, used and maintained in compliance with the provisions of Part 1926 Subpart L?Scaffolds. This includes selecting wooden planking that will meet the design specifications of the scaffold and loads imposed on it.
Does marking planks ensure a safe platform?
As you pointed out in your letter, the marking of planks does not, in itself, ensure a safe platform.
Is scaffold grade lumber required in subpart L?
Response: There is no requirement in subpart L that scaffold grade lumber be used. However, if a qualified person makes strength calculations based on lumber being scaffold grade when the lumber is not of that grade, that would raise questions about whether that person meets the definition of a qualified person.
What is OSHA plank?
OSHA planks are very tough and sturdy lumbers. They are used in the construction industry to facilitate builders in accessing the outer portion of tall buildings during construction. They are also very instrumental in helping builders to reach and repair different heights and parts of buildings.
What is the first quality of OSHA planks?
The first quality of the OSHA planks is the stiff and strong nature. They are designed in a way that they can support heavy loads placed on them without breaking. This as a result will minimize the issues of accident occurrence and guarantee long durability.
What is glulam lumber?
1.Glued laminated Lumber (Glulam) The glulam are pine boards with measurements 2×6 that are glued together to come up with a beam measuring around 6×10. Thereafter, three scaffold planks with measurements 2×10 are created from the beam. 2.
What is a pinned plank?
Pinned Planks. The pinned planks consist of three southern yellow pine measuring 2×4 and with dense structural grade pinned together using a steel pin. This helps to do away with issues of damage or accidents that may be as a result of overloading.
Why do planks need to be tested?
The planks usually undergo a series of rigorous tests to ensure they have the best quality and that they can withstand heavy loads. This ensures they have the ability to resist end splits and side splits and can, therefore, guarantee that your workers will not be involved in any accidents.
Why do manufacturers test and emboss planks?
This is to ensure that they are all performing as intended and that they are of the right quality.
Is a plank cost effective?
Basically, the initial cost of these planks is higher than that of the other types of planks. However, looking at the average cost and durability, you will realize that these planks are cost-effective. This is from the point of view that they can be used over and over again without damage. Using them will also ensure that there are no accidents, and, therefore, no additional costs in hospitals.
