For overpack and other package markings, such as the Proper Shipping Name and the shipper’s and consignee’s name and address, the minimum sizes are: At least 12 mm in size for packages larger than 30 kg or L. At least 6 mm in size for packages less than or equal to 30 kg or L. [IATA DGR 7.1.4.4]
What is the size of the “overpack” marking?
The lettering on the “OVERPACK” marking must be at least 12 mm (0.5 inches) high. (i) Transitional exception. A marking in conformance with the requirements of this paragraph in effect on December 31, 2014, may continue to be used until December 31, 2016.
What is the legal size of an Overpack in California?
§173.25 (a) (4), the overpack is marked “OVERPACK” in letters at least 12 mm (0.5″) high. §172.332 (b) (1), an identification number for a bulk packaging on an orange panel must be 100 mm (3.9″) high and of black Helvetica Medium numerals.
What is the minimum size for a salvage package?
§173.3 (c), each salvage packaging must be marked “SALVAGE” in letters at least 12 mm (0.5″) high. §173.25 (a) (4), the overpack is marked “OVERPACK” in letters at least 12 mm (0.5″) high. §172.332 (b) (1), an identification number for a bulk packaging on an orange panel must be 100 mm (3.9″) high and of black Helvetica Medium numerals.
What should be shown on the overpack?
If the inner packages contain the Environmentally Hazardous Substance (EHS) mark, then this must also be shown on the overpack. The overpack must also display orientation arrows, on two opposite sides, if the inner packages display them but they are not visible through the outer packaging.
How tall is an overpack container?
What is packaging in shipping?
What is the purpose of packaging receptacles?
What is a package?
Is an overpack a package?
Do 49CFR and TDG require net quantity marks?
See 1 more
What are the minimum dimensions for the limited quantity marking required on the completed shipment package?
The width of the border forming the square-on-point must be at least 2 mm and the minimum dimension of each side, as measured from the outside of the lines forming the border, must be 100 mm unless the package size requires a reduced size marking that must be no less than 50 mm on each side and the width of the border ...
What is the minimum size for most hazard labels?
When hazard is displayed, lettering must be at least 7.6 mm (0.3 inches) in height. For SPONTANEOUSLY COMBUSTIBLE or DANGEROUS WHEN WET labels, the words "Spontaneously" and "When Wet" must be at least 5.1 mm (0.2 inches) in height.
What is an overpack IATA?
While these definitions are all well and good – for those of us in the dangerous goods transportation world the noun “overpack” is nicely defined by IATA as “an enclosure used by a single shipper to contain one or more packages and to form one handling unit for convenience of handling and stowage”.
What is an overpack in hazmat?
US DOT's Hazardous Materials Regulations (HMR) define an overpack as “an enclosure that is used by a single consignor to provide protection or convenience in the handling of a package or to consolidate two or more packages” [49 CFR 171.8].
What is the hazardous materials labeling requirements?
OSHA has updated the requirements for labeling of hazardous chemicals under its Hazard Communication Standard (HCS). All labels are required to have pictograms, a signal word, hazard and precautionary statements, the product identifier, and supplier identification.
What are the regulations for hazmat labels?
49 CFR 172.406 states labels must be printed on or affixed to a surface (other than the bottom) of the package or containment device containing the hazardous material and be located on the same surface of the package and near the proper shipping name marking, if the package dimensions are adequate.
What is considered overpack?
In the broadest definition, an overpack is a device that contains one or more packages. It provides protection and is often used for the shipper's convenience or to consolidate two or more packages. Shrink-wrap and banding are, by this definition, overpacking materials.
What is the main required mark to identify an overpack?
Overpacks must also be marked with the word 'OVERPACK' in the official language of the country of origin. If that language is not English, French or German, then it must be marked in one of those languages also. The overpack text must be at least 12mm high and is usually in red or black.
Is an overpack considered a package?
Many shippers think this means the gross weight of the packages and materials making up the overpack, but this is incorrect because overpacks are not packages. For a shipper's declaration, for the “quantity and type of packing”, similar rules apply.
Is a pallet considered an overpack?
Overpack examples include one or more packages: Placed or stacked onto a load board such as a pallet and secured by strapping, shrink wrapping, stretch wrapping or other suitable means.
What is an overpack container?
An overpack drum is a type of protective packaging manufactured to contain non-hazardous or hazardous materials or provide outer protection for another container to prevent or mitigate damage. At its most basic definition, an overpack is simply a large container in which another smaller container can be placed.
What is the difference between overpack and all packed in one?
When different dangerous goods are packed in one outer package we should mention All packed in One on DGD. In All packed in one shipments the inner packages are not ready for transport. Outer package used should be suitable for all the Dangerous goods packed in together. They should not re act each other.
What are the requirements for chemical labels?
Labels for a hazardous chemical must contain: Name, Address and Telephone Number • Product Identifier • Signal Word • Hazard Statement(s) • Precautionary Statement(s) • Pictogram(s) Page 3 3 above, the label could state, “Do not breathe vapors or spray. Get medical attention if you feel unwell.
What is a limited quantity label?
The Limited Quantity Label (or LQ mark) is a diamond shaped symbol that is applied to packages to indicate that the products within the combination packaging are dangerous goods that are packaged in accordance with the Limited Quantity exemption.
What is the correct format for a proper hazmat description?
An easy way to remember this sequence is to refer to the acronym “ISHP”: Identification Number, Shipping Name, Hazard Class or Division, and Packing Group. If a technical name is required, it must be placed in parentheses and listed after the Proper Shipping Name or Basic Description.
What is the hazard statement on a container label?
A hazard statement is a standardized GHS phrase assigned to chemicals that describes the nature and degree of the hazard(s) associated with that chemical. Every applicable hazard statement from the SDS must be included on the container label.
49 CFR § 173.25 - Authorized packagings and overpacks.
(a) Authorized packages containing hazardous materials may be offered for transportation in an overpack as defined in § 171.8 of this subchapter, if all of the following conditions are met: (1) The package meets the requirements of §§ 173.21 and 173.24 of this subchapter. (2) The overpack is marked with the proper shipping name and identification number, when applicable, and is labeled as ...
Q&A: Is this an overpack? - Daniels Training Services
An overpack can be used to facilitate the shipment of a hazardous material. Can you identify an overpack? (815) 821-1550; [email protected]; PO Box 1232 • Freeport, IL 61032; Responsive Menu. Home; Dan’s Insights. Newsletters; Training. RCRA/Hazardous Waste. RCRA Training Options & Pricing;
What is in an Overpack? - Online Dangerous Goods Training
Note: For Air, if more than 1 overpack is being shipped then an ID mark should be displayed along with the total quantity of dangerous goods on the pallet. “Dangerous Goods contained in the Overpack must be properly marked, labelled and in a proper condition as required by the regulations.” MARKING & LABELLING OF PACKAGES. The dangerous goods regulations require that every dangerous goods ...
How high must an overpack be?
The overpack text must be at least 12mm high and is usually in red or black. The UN number of each substance inside the overpack must be shown, and this must be preceded by the capital letters ‘UN’. If the inner packages contain the Environmentally Hazardous Substance (EHS) mark, then this must also be shown on the overpack.
What is an Overpack?
Overpacks are enclosures used by shippers to contain one or more packages of dangerous goods to form a single handling unit. This makes handling and stowage more convenient during transport. Overpacks usually take the shape of several crates or boxes that have been secured to a pallet and shrink-wrapped/strapped, but they can also be single receptacles, such as a gas canister, placed into another protective outer box or other packaging. Overpacks must be marked with the word ‘Overpack’ or an Overpack label.
Why are overpacks important?
Overpacks make the loading of cargo units simpler and quicker and they can add extra protection to ensure that dangerous goods are kept safe during transport.
What language is an overpack?
Overpacks must also be marked with the word ‘OVERPACK’ in the official language of the country of origin. If that language is not English, French or German, then it must be marked in one of those languages also. The overpack text must be at least 12mm high and is usually in red or black.
When you ship an overpack by air, what should the net weight of dangerous goods be displayed?
When you ship overpacks by air the net weight of dangerous goods should be displayed if there is more than one package in the consignment. and in addition to the marks on the exterior of the overpack, you must apply the appropriate hazard labels for the contents, as well as the appropriate handling and shipping labels, ie this way up arrows, magnetized material, cargo aircraft only etc.
Do you need orientation arrows on an overpack?
The overpack must also display orientation arrows, on two opposite sides, if the inner packages display them but they are not visible through the outer packaging. If the packages contain liquids then orientation arrows are always advised on the overpack.
Do overpacks have hazard labels?
Generally, for road and rail, overpacks must show the hazard labels (warning diamonds – primary and subsidiary, if they are required) for each dangerous goods package contained in the overpack and any additional handling markings appearing on the packages.
What is the capacity of an overpack?
The word “Overpack” or “Suremballage” on at least one side of the overpack; The information required by subsection (3) on one side of the overpack, if its capacity is less than 1.8 cubic metres (64 cubic feet); and.
What information must be displayed on the overpack?
The following information must be displayed on the overpack: The primary class label and each subsidiary class label for each of the dangerous goods contained in the overpack, except that only one label is required for dangerous goods that are included in the same class; and. The shipping name and UN number of the dangerous goods.
What is the meaning of the word "overpack" in the TDG?
49 CFR regulations and IMDG regulations are similar with this statement, the overpack is marked with the word “overpack”, the proper shipping name and UN number and is labeled as required for each dangerous goods contained therein, unless markings and labels representative of each hazardous material in the overpack are visible. Only the TDG Regulations requires the use of an “overpack” mark whenever an overpack is used, regardless of the visibility of the Dangerous Goods Marks.
What are some examples of overpacks?
Examples of overpacks include: A pallet on which are placed or stacked one or more small means of containment that are secured by strap, shrink wrap, stretch wrap, nets or other similar means. A disposable box, crate or bin in which one or more small means of containment are placed.
Do you have to put the word "overpack" on an overpack?
(so you still have to put the word “overpack” on all overpacks even if all the safety marks are visible!)
Do you need an overpack mark?
Only the TDG Regulations requires the use of an “overpack” mark whenever an overpack is used, regardless of the visibility of the Dangerous Goods Marks . The upright/orientations arrows are required on the overpack for liquids on all modes of transport except for the TDG Regulations.
What is the minimum size of salvage packaging?
Many other markings have minimum size requirements as well, including but not limited to the following: §173.3 (c), each salvage packaging must be marked “SALVAGE” in letters at least 12 mm (0.5″) high.
What is packaging marked with?
Packaging manufactured prior to January 1, 2017. Packaging is permanently marked with the identification number marking. Examples of an acceptable permanent marking include embossing or a heat stamp process.
Where is the identification number on a package?
The four-digit identification number (preceded by “UN”, “NA”, or “ID” as appropriate) is found in column four of the Hazardous Material Table. Other package markings, not to mention HazMat labels, will be required as well but I don’t intend to get into that here. The purpose of this article is to bring to your attention a new (as of January 1, 2017) minimum size requirement for the height of the identification number marking on a non-bulk packaging.
How tall is an overpack container?
By the way, any time the word overpack is required on the outside of the overpack container, be sure it is 12 millimeters (~0.5 inches) tall.
What is packaging in shipping?
What is all of that in reality? Packagings are the pieces and parts that work together to make a final package. These are things like bottles, boxes, absorbent materials and even tape that make up combination packaging kits. Packagings also include things like drums, jerricans, and IBCs. Depending on the parts and how they are put together, they may have to be tested under the UN Packaging Standards. Many also have specific instructions for use and closure. A Package then is the final box, drum, etc. filled with a dangerous good that will be picked up and shipped. It is simply waiting around for a carrier to come and get it.
What is the purpose of packaging receptacles?
Packaging: One or more receptacles and any other components or materials necessary for the receptacles to perform their containment and other safety functions and to ensure compliance with the minimum packing requirements of these Regulations.
What is a package?
Package: The complete product of the packing operation consisting of the packaging and contents prepared for transport.
Is an overpack a package?
Many shippers think this means the gross weight of the packages and materials making up the overpack, but this is incorrect because overpacks are not packages. For a shipper’s declaration, for the “quantity and type of packing”, similar rules apply.
Do 49CFR and TDG require net quantity marks?
Now as a side note, none of the regulations of 49CFR, TDG and IMDG require net quantity marks to be placed on packages. Now, the paperwork for each of them does require the total net quantity of dangerous goods in the shipment. Again, not package weights and overpacks have no bearing here.
