Preparation Before you Start Papering
- Calculate the Number of Wallpaper Rolls You Need
- Check the Pattern. Before you start to measure and cut, check the pattern on the paper (the label will help here). ...
- Measure the Height of Your Room. ...
- Paper in a Clockwise Direction. ...
- Mixing the Paste. ...
- Getting the Paste on the Paper. ...
- Getting the Paper on the Wall. ...
- Hanging Paper Round an External Corner. ...
How do you hang wallpaper on a corner of a wall?
Pull the paper off the wall enough to cut and then brush it back into place. Brush the paper tightly into the corner and you should have about 25mm overlap on the adjoining wall. This can be trimmed back to about 5 or 10mm and the length of wallpaper (which will be hung later) will overlap it.
Which direction should you wallpapering around the room?
We always suggest you wallpaper round the room in a clockwise direction in a room with no focal point, e.g a fireplace. Where to Begin Wallpapering? If the room has such a prominent point then begin there, especially with large patterned paper, by centering the pattern over the focal point.
How do you stick a pattern to a wall with paper?
Then paste and hang the cut length and fit the paper to the edge of the previous strip, aligning the pattern at eye level. Allow the extra 25mm to stick lightly to the next wall, and use a paper-hanging brush to smooth the paper into the internal corner.
How to install wallpaper on a window wall?
Measure the paper width less 10mm from the edge of the window wall. Start there to help conceal any slight overlaps. Hang the long edge of the wallpaper parallel to the window wall. Choose steps suitable for the ceiling height. Move them around as you work. Don’t lean or overstretch and risk a fall. Cut, paste and soak as before.
Which direction should you wallpaper?
We recommend hanging wallpaper vertically unless the pattern requires it to be hung horizontally. If hanging over lining paper, hanging it in the opposite direction to the lining paper means that the seams won't fall in the same place and create ridges.
Do you wallpaper towards the light or away from it?
Also, it's best to work away from the window, so the paper edges don't cast a shadow if they overlap slightly. And try to avoid having to hang narrow strips against a window or door.
Do you start wallpapering from the middle?
Using a paper hanger's brush, smooth the paper on to the wall, starting at the top and brushing from the middle using gentle strokes. Use the brush to push the paper into the join with the ceiling.
How do you know where to start wallpapering?
0:034:27Hanging Your First Strip of Wallpaper - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen deciding where to begin if hanging wallpaper on all four walls you ideally want to start in theMoreWhen deciding where to begin if hanging wallpaper on all four walls you ideally want to start in the most inconspicuous corner of the room.
Where do you start when wallpapering in a hallway?
Where to start papering the hall, stairs and landing. You should start by hanging the longest sheet first down the stairwell, and working along one way until a corner.
How long does it take to wallpaper 1 wall?
of-course, duration will depend on the size of your wall. Say if there's only 1 roll to be installed, then it would barely take a 1.5-2 hours. 1 roll which is 55-57 sq feet. If you have a column or other design element to that wall, then it take 3-4 hrs max.
How long do you leave paste on wallpaper before hanging?
3 Soak the wallpaper You will now need to let the paste soak into the wallpaper (the time required for this should be stated on the packaging of the paste - usually between 5 and 10 minutes). Fold the pasted wallpaper strip in from the outside edges to the middle point that you marked earlier.
Do you wallpaper around corners?
Never hang a full width wallcovering around an inside corner. Always do it in two pieces. First measure the distance from the edge of the last piece you hung to the corner. Do this at several points between the ceiling and skirting to find the maximum distance.
How do you start wallpapering?
0:507:06How to wallpaper a room with Wickes - YouTubeYouTubeStart of suggested clipEnd of suggested clipFollowing the manufacturer's instructions mix the paste the wall adhesive. Use a roller to apply theMoreFollowing the manufacturer's instructions mix the paste the wall adhesive. Use a roller to apply the adhesive to the section of wall you're about to cover with your first piece of paper.
How do you wallpaper to the edge?
0:371:50Wallpaper corners. How to - Step by step - YouTubeYouTubeStart of suggested clipEnd of suggested clipCut the strip with a paper hanging cutting block and a paper hanging ruler save the part that's leftMoreCut the strip with a paper hanging cutting block and a paper hanging ruler save the part that's left for the next step glue and attach the strip edge to edge and press firmly all the way.
How do you hang wallpaper without seams showing?
Wallpaper seams on straight walls are butted, not overlapped, but seams are less visible if you place them at the point farthest from where the first panel was installed. Minimize the visibility of seams by starting in the area opposite the most-used entrance to the room.
How do you hang wallpaper with a pattern?
1:342:51Hanging Patterned Wallpaper | DIY Projects - YouTubeYouTubeStart of suggested clipEnd of suggested clipBefore gluing position the second strip next to the first to check that the pattern lines. Up cutMoreBefore gluing position the second strip next to the first to check that the pattern lines. Up cut according to the pattern stick to the wall making sure to keep the strip. Aligned.
How do you wallpaper around a light?
0:001:19How to Hang Wallpaper Around Light Switches and Doors - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing your scissors cut a diagonal line so that the paper will sit back against the wall and frameMoreUsing your scissors cut a diagonal line so that the paper will sit back against the wall and frame gently smooth the paper into the edges. Around the frame and cut with a sharp knife or scissors.
How do you put wall paper on the wall light?
0:202:31How to Hang Wallpaper Part 7- Working around Light FittingsYouTubeStart of suggested clipEnd of suggested clipAnd then trim using a straight edge and a sharp knife most modern fittings have snap-on covers whichMoreAnd then trim using a straight edge and a sharp knife most modern fittings have snap-on covers which makes this job a lot.
How do you wallpaper around awkward shapes?
0:421:41How to Wallpaper those Tricky bits - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo always take your radiators off and paper all the way down unscrew the radiator brackets. And putMoreSo always take your radiators off and paper all the way down unscrew the radiator brackets. And put matchsticks in the screw holes poked. Them through the wallpaper.
How many rolls of wallpaper do I need for a small powder room?
If you have a powder room and you're using my installer, you will need six single (American) rolls, or 3 double (European rolls).
How to lay out a wall?
A. Use a roll to lay out the wall. Use a full roll of paper as a guide to lay out the room. Butt a roll into the corner where you plan to start, and make a pencil mark on the wall at the edge of the roll. Slide the roll down to that mark, and make another pencil mark at the other edge of the roll. Keep doing this until you know where every seam is ...
How to make a corner wall?
You’ll need to create a seam at every inside corner to make the next panel plumb. The first panel installed in a corner should be overlapped onto the adjacent wall at least 1/8 in. When working your way into a corner, measure over from the last panel to the corner at the top, middle and bottom. Then cut the corner panel 1/8 in. longer than the longest of the three measurements. You can use the leftover piece to start the new wall, but you may need to cut it at a slight angle to accommodate a crooked corner. Some wallpaper won’t stick to other wallpaper, so run a small bead of seam adhesive in the corner before overlapping the second piece.
How to keep edges from curling?
Set your edges with a roller. Don’t press too hard and squeeze out too much adhesive. To keep the edges from curling, you need to set them with a roller. But the same rule that applies to the smoother applies to the roller: Don’t press too hard or you’ll squeeze out too much adhesive.
How to get paper straight?
The longer the paper, the easier it is to get straight. Cut a bunch of pieces of paper at once, and book several at the same time. Set each roll in front of the wall where it’s going to be hung. If you’re a beginner, set them in a plastic bag to give you more time to work with them.
How many thirds of paper should you fold?
Fold the paper so that when you unfold it, you’ll be working with two-thirds of the panel.
Why is it important to use wall size?
Using wall size will help the paper adhere to the wall and reduce the chance that the paper will shrink. It also makes it easier to remove the paper when the time comes.
Who is the guy that hangs wallpaper?
Bob Rowland has been hanging wallpaper for more than 44 years. He’s covered hundreds of acres of commercial walls and has worked on everything from modest starter homes up to the governor’s mansion in St. Paul, MN. He’s one of our best resources for learning best practices for how to install wallpaper.
How to make a corner wallpaper?
You need to wallpaper round a corner with two narrow strips to keep both edges vertical. Measure the widest gap between the last drop and the corner. Add about 20mm to that width and use a straight edge to mark it out in pencil on the back of your wallpaper. Cut the drop into two strips vertically.
How long does it take to hang wallpaper?
Watch How do you hang wallpaper for a 90 second overview. The part on pasting starts at about 35 seconds. Ready mixed pastes are usually best. Check the wallpaper label to see which one the manufacturer recommends, and how long you need to let it soak in before you hang the paper.
How to hang wallpaper on a plug socket?
Hang your wallpaper unpasted to match the last drop, and feel through the paper to find the corners of your plug socket. Cut slits in the paper diagonally out from near the middle of the socket to each of the corners. Paste your paper, including the outer corners of the slits, and allow the paste to soak in as usual.
What is the best way to keep wallpaper clean?
A dustsheet on the floor will help keep your wallpaper clean as you work.
How to trim extra off of wallpaper?
You’ll trim the extra off after you’ve hung the wallpaper. Measure out the drop length on the back of your paper. Mark a straight line across the back and make your cut. A dustsheet on the floor will help keep your wallpaper clean as you work. Check your first drop dry against the wall before you paste or cut any more.
How far up do you line up a paste drop?
Line up the edge of your first pasted drop about 5mm inside the pencil line.
Where to start paper join?
Unless you’ve got a bold pattern, start in the least noticable corner. A paper join behind a door will be hidden when the door is open.
How to wallpaper in corners?
How to wallpaper in internal corners. When you're papering in corners, it's much easier to cut a length of paper vertically and position the join at the corner, especially when your wall is slightly crooked or your corner isn't completely square. Measure and cut the paper so that it reaches slightly beyond the corner.
How to hang wallpaper on a fireplace?
If necessary, cut the first length in half vertically along the edge that'll overlap the corner. Last but not least, if your wallpaper has a large pattern, it's a good idea to hang the first length over a fireplace or other focal point. Then work away from it in both directions to make the design central and symmetrical.
How to get rid of wallpaper paste?
Step 1. To position your first length of wallpaper, use a plumb line or spirit level to draw a line from ceiling to skirting board, 480mm out from the corner. This allows a 50mm overlap onto the window wall. Step 2.
How to pierce paper with a matchstick?
As you hang your paper, bring it over the marked position and press the paper onto the matchstick to pierce the paper. Then smooth the paper with a paperhanging brush. When the paper is quite dry, remove the matchstick and replace the fitting.
How to hang a paper skirting board?
Ideally begin at the corner and hang your first length of paper on a wall with no doors or windows. That way, you can hang a full length from the ceiling to the top of the skirting-board. Choose a wall to the right of the window if you're right-handed or to the left if you're left-handed.
How to make a single feature wall?
Step 1. Measure the distance between the edge of the last length you've hung and the corner at the top, bottom and middle of the wall. Use the widest measurement and allow an extra 25mm for turning onto the next wall. Cut a length of paper to this width.
How to make a vertical edge on a wall?
Hang the plumb line on the next wall at a distance from the corner that's either the width of the full paper roll or your offcut (whichever you're using). Make some pencil marks behind the vertical line at intervals down the wall. This will give you a completely vertical edge for starting the next wall.
How to make a corner wallpaper?
You need to wallpaper round a corner with two narrow strips to keep both edges vertical. Measure the widest gap between the last drop and the corner. Add about 20mm to that width and use a straight edge to mark it out in pencil on the back of your wallpaper. Cut the drop into two strips vertically.
How long does it take to hang wallpaper?
Watch How do you hang wallpaper for a 90 second overview. The part on pasting starts at about 35 seconds. Ready mixed pastes are usually best. Check the wallpaper label to see which one the manufacturer recommends, and how long you need to let it soak in before you hang the paper.
What is the best way to keep wallpaper clean?
A dustsheet on the floor will help keep your wallpaper clean as you work.
How to hang wallpaper on a plug socket?
Hang your wallpaper unpasted to match the last drop, and feel through the paper to find the corners of your plug socket. Cut slits in the paper diagonally out from near the middle of the socket to each of the corners. Paste your paper, including the outer corners of the slits, and allow the paste to soak in as usual.
How to trim extra off of wallpaper?
You’ll trim the extra off after you’ve hung the wallpaper. Measure out the drop length on the back of your paper. Mark a straight line across the back and make your cut. A dustsheet on the floor will help keep your wallpaper clean as you work. Check your first drop dry against the wall before you paste or cut any more.
How to hide a paper join behind a door?
A paper join behind a door will be hidden when the door is open. Make a mark about 25mm less than the width of your wallpaper away from the corner. Use a plumb line or a spirit level to pencil a long vertical line down the wall. Line up the edge of your first pasted drop about 5mm inside the pencil line.
How to make a paper drop?
Line up the edge of your first pasted drop about 5mm inside the pencil line. Brush in towards the corner and take the last 25mm around it, then brush out from the centre to the edges all the way down. Use scissors to gently crease the paper, then peel back and trim along the crease. Repeat at the bottom of the drop.
How to hang a strip in a corner?
Hang a strip in the corner. Overlap the existing piece on the adjacent wall by 1/8 inch. Measure to the plumb line and adjust the paper to keep the distance equal. Smooth the paper. Trim at the ceiling and trim the corner.
How to hang a book on a wall?
Start in a corner near a door. If the door is far from the corner, draw a reference line parallel to the door near the corner. Unfold the top of the booked paper and hang it on the wall. Overlap about 2 inches at the ceiling and 1/8 inch in the corner. Lightly press it in place.
How to get air bubbles out of paper?
Tip: Push air bubbles out by sweeping the paper smoother from the center out to the edges. Wipe off paste on the surface with a sponge.
How to lock a paper seam?
Unfold the bottom of the sheet and finish matching and closing the seam. Then tightly roll down the entire seam, working a full 3 inches in from the edge. This locks the seam, keeping it from opening as you smooth the paper.
How to get rid of curling wallpaper?
As you do, check for defects and drag the paper against the edge of your worktable to take away the curl. Cut the paper into sheets 4 inches longer than the height of your walls. Cut in the same place on the repeat so patterns on adjacent sheets will line up. Lay a cut sheet on the table, face down.
Where to press cut edge in molding?
Press the cut edge tight in the joint between the molding and the wall.
Is it bad to hang paper straight?
5 Moderate Not bad for someone with patience and precision, which are ket to hanging paper straight, plumb, and perfectly aligned.
Which way should wallpaper be placed in a room with no focal point?
We always suggest you wallpaper round the room in a clockwise direction in a room with no focal point, e.g a fireplace.
How to measure for wallpaper?
Try and start the papering on a wall where no window or item of a similar exists then (Its important to remember that the corners of your room are extremely unlikely to be absolutely vertical or square so you need to make sure the very first strip of paper you put up is plumb) measure along the wall, from one corner of the room, the width of your wallpaper less 25mm and mark a vertical line from ceiling to skirting board with a spirit level.
How to cut a skirting board with paper?
Brush the paper up to the crease between ceiling and wall and also the crease between skirting board and wall. Then double check the edge of the paper is on the line you drew on the wall and press the paper into both the creases with the back edge of your paperhanging scissors. This should give you a line to cut along.
How to keep wallpaper from curling back up?
The ends can be prevented from curling back up into a roll by tying a piece of string, across the table, to the legs.
How to paste on paper?
Getting the Paste on the Paper. Paste the paper by working from the middle of each length to the outside and store by folding the wet sides together as shown. If you are careful and by lining up the lengths you have cut with the top edge of the table you should be able to paste 3 or 4 lengths at the same “sitting”.
How to get air bubbles out of paper?
Unfold the paper gently onto the wall using your hanging brush to brush down the middle and out towards both edges. This brushing makes sure that the paper makes contact with the wall and at the same time brushes out any air bubbles which may have got trapped under the paper.
What is the standard size of wallpaper?
Most wallpapers come in a standard size of 530mm wide and 10.5m long. Woodchip paper and lining paper along with a few other “specials” come in longer or differing width rolls. Measure round the room for the number of rolls you need using the chart below.
1. Start with the walls
Wondering if you should wallpaper walls or windows first? The answer is to start with the walls. The first length of wallpaper in a room should be hung on the wall next to the wall with the main window.
2. Overlap the window frame
As you reach a window recess, hang a full length drop of wallpaper overlapping the opening.
3. Cut the wallpaper at the top and bottom of the recess
Using the scissors, make a horizontal cut level with the top edge of the recess. Make a parallel cut level with top of the windowsill. These cuts will allow the wallpaper to cover the side of the recess.
4. Smooth the wallpaper into the reveal
If there is sufficient wallpaper to fit the depth of reveal, crease it around the corner using a paper-hanging brush.
5. Trim the wallpaper
Run the scissors along the crease to create a cutting line. Gently peel back the wallpaper and trim to fit. Use the brush to smooth the paper into place.
6. Work from the top of the wall
Cut a piece of wallpaper large enough to extend from the ceiling above the window to the window and into the recess as far as the window frame, allowing some extra for trimming.
7. Wallpaper under the windowsill
Measure from the top of the baseboard to the windowsill and add an extra 2 inches (50mm) for trimming. Cut the strips of wallpaper to this length to cover the area below the window.
1. Start with the walls
Wondering if you should wallpaper walls or windows first? The answer is to start with the walls. The first length of wallpaper in a room should be hung on the wall next to the wall with the main window.
2. Overlap the window frame
As you reach a window recess, hang a full length drop of wallpaper overlapping the opening.
3. Cut the wallpaper at the top and bottom of the recess
Using the scissors, make a horizontal cut level with the top edge of the recess. Make a parallel cut level with top of the windowsill. These cuts will allow the wallpaper to cover the side of the recess.
4. Smooth the wallpaper into the reveal
If there is sufficient wallpaper to fit the depth of reveal, crease it around the corner using a paper-hanging brush.
5. Trim the wallpaper
Run the scissors along the crease to create a cutting line. Gently peel back the wallpaper and trim to fit. Use the brush to smooth the paper into place.
6. Work from the top of the wall
Cut a piece of wallpaper large enough to extend from the ceiling above the window to the window and into the recess as far as the window frame, allowing some extra for trimming.
7. Wallpaper under the windowsill
Measure from the top of the baseboard to the windowsill and add an extra 2 inches (50mm) for trimming. Cut the strips of wallpaper to this length to cover the area below the window.
How to apply a border to a wall?
Each border strip should extend to the full width of wall plus 1/2" to extend around corners. Submerge border in water tray for prescribed time from the directions, book by loosely folding in an accordion fashion, and apply to the wall. If the border is being applied over wallcovering, do not wet border. You would use a vinyl to vinyl adhesive to hang the border. Wrapping corners by about 1/4" and smooth the surface. Make sure you wipe excess pasted off of the surface with a clean sponge.
Why do we reverse hang wallpaper?
Reverse hanging is done to mitigate shading variances that can occur on a run of paper. It is only done when the wallpaper has no pattern.
What does reverse wallpaper mean?
A: Answer Reverse hanging wallpaper means that every other strip of paper is installed in the opposite direction from how it comes off the roll. If the first strip is hung as it comes off the roll, the second strip would be rotated 180° and hung "upside down.".
How long does it take to shave wallpaper?
When soaking the surface with a stripper allow time for the solution to soften the paste. Usually a 15 to 20 minute period is enough. Apply more solution prior to beginning to scrape.
Can you use a paste activator on wallpaper?
A: Answer At times the soaking process can be somewhat messy. For those wanting to avoid this, we do offer a paste activator. The paste activator can be brushed onto the back of the wallpaper in the same manner as paste. Once applied, book the segment of paper and set to one side so that the paste can become completely activated prior to hanging.
Can you use a wallpaper shaver to remove plaster?
A: Answer Sometime papers can simply be peeled off. If not a wallpaper shaver can sometimes be used to remove the paper from plaster walls without the need of liquid stripper. If these options do not work a chemical stripper may be needed.Many papers today are either solid vinyl or have a vinyl coating. This makes it difficult for stripper solutions applied to the surface to act on the adhesive. There are tools that can be used to perforate the surface of the wallpaper. Perforating the paper will save you time and effort in the stripping process. Using the right tool to scrape will also save time. A wallpaper shaver has a sharp edge and will actually minimize the damage to the wall. When soaking the surface with a stripper allow time for the solution to soften the paste. Usually a 15 to 20 minute period is enough. Apply more solution prior to beginning to scrape. If you do these things you should find that project just got a lot easier.
